JAI, Oxford
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
PAMELA (Particle Accelerator for MEdicaL Applications) employs novel non-scaling Fixed Field Alternating Gradient (NS-FFAG) technology in the development of a proton and C6+ particle therapy facility. One of the challenges of this design is the acceleration of high energy C6+ in a lattice which enables high flexibility and reliability for treatments, yet remains minimal in size and complexity. Discussed here is the Carbon 6+ lattice solution in terms of both design and performance.
Muons, Inc, Batavia
JLAB, Newport News, Virginia
ODU, Norfolk, Virginia
Parametric-resonance Ionization Cooling (PIC) is envisioned as the final 6D cooling stage of a high-luminosity muon collider. Implementing PIC imposes stringent constraints on the cooling channel's magnetic optics design. This paper presents a linear optics solution compatible with PIC. Our solution consists of a superposition of two opposite-helicity equal-period and equal-strength helical dipole harmonics and a straight normal quadrupole. We demonstrate that such a system can be adjusted to meet all of the PIC linear optics requirements while retaining large acceptance.
CNAO Foundation, Milan
CERN, Geneva
LPSC, Grenoble
INFN/LNF, Frascati (Roma)
CNAO is a synchrotron accelerator presently under commissioning in Pavia. The aim of this accelerator is to treat tumors with hadrons and to perform advanced clinical and radiobiological research. The CNAO will start treating patients with protons (60-250 MeV range) and carbon ions (120-400 MeV/u range) in three treatment rooms with four beam lines. Future upgrade with gantries is foreseen. This paper describes the design, magnetic measurements and sorting criterion used for the sixteen synchrotron main dipoles and twenty-four quadrupoles. The magnetic measurements results are compared with magnetic simulation.
RCNP, Osaka
KT Science Ltd., Akashi
NIRS, Chiba-shi
CYRIC, Sendai
A scanning magnet using high-temperature superconductor (HTS) wire was designed, fabricated, and tested for its suitability as beam scanner. After successful cooling tests, the magnet performance was studied using DC and AC currents. With DC current the magnet was successfully operated to generate designed field distributions and effective length. In AC mode, the magnet was operated at frequencies of 30-59 Hz and a temperature of 77 K as well as 10-20 Hz and 20K. The power loss dissipated in the coils was measured and compared with the model calculations. The observed loss per cycle was independent of the frequency and the scaling law of the excitation current was consistent with theoretical predictions for hysteretic losses in HTS wires.
Fermilab, Batavia
Synchro-betatron resonances can lead to emittance growth and the loss of luminosity. We consider the detailed dynamics of a bunch near such a low order resonance driven by crossing angles at the collision points. We characterize the nature of diffusion and find that it is anomalous and sub-diffusive. This affects both the shape of the beam distribution and the time scales for growth. Predictions of a simplified anomalous diffusion model are compared with direct simulations.
BNL, Upton, Long Island, New York
In this report we present recent experimental data from the Relativistic Heavy ion Collider (RHIC) illustrating effects resulting from of ~ 10 Hz vibrations of the triplet quadrupole magnets in the interactions regions and evaluate the impact of these vibrations on RHIC collider performance. Measurements revealed modulation of the betatron tunes of appreciable magnitude relative to the beam-beam parameter. Comparison of the discrete frequencies in the spectra of the measured beam positions and betatron tunes confirmed a common source. The tune modulations were shown to result from feed-down in the sextupole magnets in the interaction regions. In addition we show that the distortions to the closed orbit of the two counter-rotating beams produced a modulated crossing angle at the interaction point(s).
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
JAI, Oxford
A novel nonlinear, nonscaling FFAG ring has been designed for proton and ion acceleration [1]. It can be used for proton and carbon therapy as well as a proton driver for various facilities such as a high intensity neutrino factory. The machine has novel features including variable energy extraction and a high repetition rate of about 1 kHz. Taking as an example the PAMELA proton ring, under study at the John Adams Institute in Oxford, we present results of an error study. A calculation of alignment tolerance is made, in which the effects of translational misalignments of the triplet magnets are included. The effect of misalignments on the dynamic aperture of the machine is investigated.
[1] S. L. Sheehy, K. J. Peach, H. Witte, D. J. Kelliher and S. Machida, Phys. Rev. ST Accel. Beams, 13 (2010) 040101
PSI, Villigen
A new current monitor (MHC5) based on a re-entrant cavity tuned at the 2nd RF harmonic (101.26 MHz) has been in operation since April 2009 at PSI. It monitors the current of the high intensity 590 MeV proton beam at 8 m downstream of the graphite meson production target (TgE). The scattered particles and their secondaries from TgE introduce a heavy thermal load approximately of 230 W on MHC5 at 2 mA beam intensity, which is carried away by active water cooling. The inhomogeneous temperature profile in MHC5 results in thermomechanical deformations which leads to a change in its HF electromagnetic characteristics. Indeed, an anomalous RF drifts were observed during initial operations, which had to be compensated for, to obtain correct beam current monitoring. In this paper, the physics of the observed RF drift is analyzed by using advanced multiphysics simulation technologies.
ORNL, Oak Ridge, Tennessee
The Spallation Neutron Source accelerator complex consists of a 2.5 MeV H- front-end injector system, a 186 MeV normal-conducting linear accelerator, a 1 GeV superconducting linear accelerator, an accumulator ring, and associated beam transport lines. Since initial operation began in 2006, the beam power has been steadily increasing toward the design goal of 1.4 MW. In September 2009 the power surpassed 1 MW for the first time, and operation at the 1 MW level is now routine. The status of the beam power ramp-up program and present operational limitations will be described.
CEA, Gif-sur-Yvette
BNL, Upton, Long Island, New York
To preserve proton polarization through acceleration, it is important to have a correct model of the process. It has been known that with the insertion of the two helical partial Siberian snakes in the Alternating Gradient Synchrotron (AGS), the MAD model of AGS can not deal with a field map with offset orbit. The stepwise ray-tracing code Zgoubi provides a tool to represent the real electro-magnetic fields in the modeling of the optics and spin dynamics for the AGS. Numerical experiments of resonance crossing, including spin dynamics in presence of the snakes and Q-jump, have been performed in AGS lattice models, using Zgoubi. This contribution reports on various results so obtained.
JINR, Dubna, Moscow Region
Cockcroft Institute, Warrington, Cheshire
The Ultra-Low energy Storage Ring (USR) within the future Facility for Low-energy Antiproton and Ion Research (FLAIR) will decelerate antiproton beams from 300 keV to energies of only 20 keV. Cooled beams will then be extracted and provided to external experiments. The large variety of planned experiments requires a highly flexible longitudinal time structure of the extracted bunches, ranging from ultra-short pulses in the nanosecond regime to quasi DC beams. This requires fast as well as slow extraction in order to cover whole range of envisaged beam parameters. A particular challenge was to combine elements for fast and slow extraction in one straight section of this electrostatic ring. In this contribution we present the results of beam dynamic simulations and describe the overall extraction scheme in detail.
IAP, Frankfurt am Main
Kress GmbH, Biebergemuend
NSCL, East Lansing, Michigan
A new reaccelerator facility ReA3 is currently under construction for National Superconducting Cyclotron Laboratory (NSCL) at Michigan State University (MSU). As part of that project a new 3.5 m long 4-rod Radio Frequency Quadrupole (RFQ) has been build. This RFQ accelerates ions with a Q/A ratio of 0.2 up to 0.5 from an input energy of 12 keV/u to the final energy of 600 keV/u. We have designed the 80.5 MHz-RFQ with a square cavity cross section. It was build and tuned in Frankfurt and has been delivered to MSU. The design and the tuning process of the ReA3-RFQ will be discribed in this paper.
Kyoto ICR, Uji, Kyoto
MPI-K, Heidelberg
Kyoto IAE, Kyoto
HU/AdSM, Higashi-Hiroshima
NIRS, Chiba-shi
JINR, Dubna, Moscow Region
Transverse laser cooling with the use of a synchro-betatron coupling is experimentally demonstrated at the ion storage/cooler ring S-LSR. Bunched 40keV 24Mg+ beams are cooled by a co-propagating laser with a wavelength of 280nm. Synchrotron oscillation and horizontal betatron oscillation are coupled by an RF drifttube at a finite dispersive section (D = 1.1m) in order to transmit longitudinal cooling force to the horizontal degree of freedom*. Time evolution of horizontal beam size during laser cooling was measured by a CCD camera**. Horizontal beam sizes were reduced by 0.13mm within 1.5s after injection when the tune values satisfy a difference resonance condition, νs - νh = integer, at the operating tunes of (νh, νv, νs)=(2.067, 1.104, 0.067) and (2.058, 1.101, 0.058). Without resonance condition, the size reduction was negligibly small. The momentum spread was 1.7x10-4 on the resonance otherwise 1.2x10-4. These results show that the horizontal heats are transferred to the longitudinal direction through the synchro-betatron coupling with the resonance condition and are cooled down by a usual longitudinal bunched beam laser cooling.
* H. Okamoto, Phys. Rev. E 50, 4982 (1994).
** M. Nakao et. al., contribution to this conference.
Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Berlin
Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Elektronen-Speicherring BESSY II, Berlin
With a 7T wiggler in operation any attempts to detect the resonant depolarization of the electron spins were unsuccessful at BESSY II. This was attributed to the severely reduced final degree of spin polarization in the alternating fields of the strong wiggler which on the other hand nearly double the radiation loss per turn. The key to a clear detection of the depolarization were the improvement of the sensitivity of the polarimeter based on the spin dependent Touschek scattering cross section and the more effective and thus full depolarization of the beam. In the paper the steps taken will be presented in detail. With these improvements in place the high precision energy determination of the stored beam can be performed once again in parallel to the normal user operation and without any noticeable perturbations to the beam.
HU/AdSM, Higashi-Hiroshima
The University of Tokyo, Institute of Physics, Tokyo
MPQ, Garching, Munich
RIKEN, Wako, Saitama
Hiroshima University, Graduate School of Advanced Sciences of Matter, Higashi-Hiroshima
Tokyo University of Science, Tokyo
In Antiproton Decelerator (AD) at CERN, unique low energy antiproton beams of 5.6 MeV have been delivered for physics experiments. Furthermore, the RFQ decelerator (RFQD) dedicated for Atomic Spectroscopy And Collisions Using Slow Antiprotons (ASACUSA) collaboration enables the use of 100 keV pulsed antiproton beams for experiments. What is more, Mono-energetic Ultra Slow Antiproton Source for High-precision Investigations (MUSASHI) in ASACUSA can produce antiproton beams with the energy of 100 ~ 1000 eV. Since the successful extraction of 250 eV antiproton beams reported in 2005, continuous improvements on beam quality and equipments have been conducted. Here, the basic properties of a tank circuit attached to MUSASHI trap are reported. Signals from a tank circuit provide information on the trapped antiprotons, as Shottky signals do for high energy beams in accelerators. In fact, it is known that this kind of trap-based beams are physically equivalent with those in a FODO lattice. Monitoring the tank circuit signals will be useful for on-line handling of the low energy antiproton beams from MUSASHI.
CERN, Geneva
The beta function has a fundamental impact on the LHC performance and on the functioning of its machine protection and collimation systems. A new beta-beat diagnostic system, prototyped at the SPS, has been used to verify the time-dependent variations of the LHC lattice with unprecedented 1% beta-beta resolution and at a measurement bandwidth of about 1 Hz.
PSI, Villigen
For high intensity beam operation (3mA, 1.8MW) in the PSI cyclotron, a new current monitor for proton beams has been installed during the 2009 maintenance period. This current monitor is an actively cooled re-entrant cavity with its resonance tuned at the 2nd RF harmonic (101 MHz). Operating this system presents several challenges due to the heavy shower of energetic particles, the resonator being placed 8 m behind a graphite target. The resonator is actively cooled with water, its external surface was blackened to improve the radiation cooling and its mechanical structure was optimized for good heat conduction. The resonance characteristics are extremely sensitive to structural changes of the resonator. Because of non-uniform temperature distribution and dynamical changes the observed gain drift during operation is of the order of 10%. To correct these drifts 2 tests signals 50 kHz off the RF frequency are measured on-line during beam operation. They provide an innovative mean to estimate and to correct on-line the resonator gain. This paper will present the measurement method and the achieved performances.
BNL, Upton, Long Island, New York
CEA, Gif-sur-Yvette
Commissioning of spin flipper in the RHIC (Relativistic Heavy Ion Collider) Blue ring during the 2009 RHIC polarized proton run showed significant global vertical coherent betatron oscillations induced by a two AC dipole plus four DC dipole configuration. These global orbital coherent oscillations affected collision rates and Yellow beam polarization when beams were in collision. The measured depolarizing strength of of the two AC dipoles at a phase difference of 180 degrees at injection with a different spin tune also confirmed that a single isolated spin resonance can not be induced in the presence of this global vertical coherent betatron oscillation. Hence, a new design was proposed to eliminate the coherent orbital oscillation outside the spin flipper with three additional AC dipoles. This paper presents the new design and supporting numerical simulations. In the RHIC 2010 Au run, only one AC dipole was inserted between the two original AC dipoles; and the measured closure of this AC dipole bump is also presented.
This work is under the auspices of the US Department of Energy
J-PARC, KEK & JAEA, Ibaraki-ken
The J-PARC accelerator facility consists of a 400 MeV H- linac, a 3-GeV RCS, a 50-GeV MR (Main Ring) and related experimental facilities. Beam commissioning of the facility is started from the upstream accelerators while construction of the downstream accelerators and experimental facilities is in progress. The beam commissioning of MR, MLF(Materials and Life science experimental Facility) and Hadron experimental facility started in JFY 2008. In this presentation, we present an overview of the J-PARC commissioning status. Recent progress of MR commissioning will be described in more detail. The talk will focus on the issues, challenges, solutions, and lessons learned during the commissioning and early operations of J-PARC.
HU/AdSM, Higashi-Hiroshima
Hiroshima University, Higashi-Hiroshima
LLNL, Livermore, California
S-POD (Simulator for Particle Orbit Dynamics) is a tabletop, non-neutral plasma trap system developed at Hiroshima University for fundamental beam physics studies. The main components of S-POD include a compact radio-frequency quadrupole trap, various AC and DC power supplies, a vacuum system, a laser cooler, several diagnostics, and a comprehensive computer control system. A large number of ions, produced through the electron bombardment process, are captured and confined in the RFQ trap to emulate collective phenomena in space-charge-dominated beams traveling in periodic linear focusing lattices. This unique experiment is based on the isomorphism between a one-component plasma in the laboratory frame and a charged-particle beam in the center-of-mass frame. We here employ S-POD to explore the coherent betatron resonance instability which is an important issue in modern high-power accelerators. Ion loss behaviors and transverse plasma profiles are measured under various conditions to identify the parameter-dependence of resonance stopbands. Experimental observations are compared with PIC simulation results obtained with the WARP code.
RIKEN/SPring-8, Hyogo
The pulse width of an X-ray laser at XFEL/SPring-8 is several tens femto-seconds, which requires reference rf signals to have the same time-stability. The reference signals with a low phase-noise oscillator are sent to instruments in 19" racks developed along an accelerator by an optical fiber system. The temperature drift of the fiber makes phase shifts of the reference signals. Therefore, the fiber is put in a thermal-insulated duct. By feeding temperature-controlled water (26.1 ± 0.1 deg. C) in a pipe attached to the duct, the fiber temperature was kept to be 26.2 ± 0.08 deg. C at the ambient temperature change of 29.1 ± 1.7 deg. C. From this temperature controllability, the phase shifts of the signals through a 400 m fiber of a thermal coefficient of 5 ps/km/K are 160 fs. Further reduction of the shifts is required and will be achieved by a fiber-length feedback control in a future plan. Vibration of the fiber also degrades the quality of the signals. The fiber is embedded on a vibration buffer material. A test to evaluate the effect of the vibration to the transmitted signal phase was carried out. The test result will be also shown in this paper.
DESY, Hamburg
The Free Electron Laser in Hamburg (FLASH) is a user facility providing high brilliant laser light for experiments. It is also a unique facility for testing the superconducting accelerator technologies. FLASH cavities are operating at pulsed mode. There is a filling stage to build the RF voltage in the cavities and then follow a flattop for beam operation. By the limitation of the klystron pulse length the filling time of the cavities is limited to several hundred microseconds. In order to fill the cavities to the dedicated voltage usually large RF power is required for the filling stage. For European XFEL during RF operation the klystrons will be working quite near the saturation point for better efficiency. So lowering the unnecessary klystron peak power under closed loop operation is very important for close-limitation operation. The paper will present the method which allows decreasing the required klystron peak power as well as the reflected power by filling the cavity in resonance. Simulation results will be presented as well as experimental demonstrations at FLASH.
INFN-Pisa, Pisa
University of Pisa and INFN, Pisa
Active devices based on piezoelectric actuators are widely used to dump unwanted vibrations in a variety of applications; for instance fast tuners for superconducting RF cavities. In another poster, we describe a low cost modular system of drivers for piezoelectric actuators developed at INFN-Pisa; we show here that the same system can easily be extended, with the inclusion of a simple plug-in board, to include sufficient I/O and computing capability to allow control of the device up to frequencies in the kHz range. This implementation is extremely cost effective and can be used in all situations where a high granularity distributed control system is desirable. We also show our first test results obtained using this system to control a warm single cell 1.3 GHz cavity. The cavity is perturbed using a piezoelectric actuator to generate random noise, while another piezo is used in the control loop to stabilize the resonance frequency. We use the phase of the RF pickup from the cavity as a measure of the deviation from the resonance caused by the perturbation. This simple setup allows to easily test various control algorithms without the need to work at large complex facilities.
JAEA/J-PARC, Tokai-mura
KEK/JAEA, Ibaraki-Ken
J-PARC, KEK & JAEA, Ibaraki-ken
KEK, Ibaraki
Applying narrow band longitudinal noise to the beam in J-PARC Main Ring in flattop, while the acceleration voltage is off might help to counteract the effect of ripple on the slow extraction. For this purpose, a complex noise sequence output by DSP modulates a custom made DDS synthesizer to create single side spectra without carrier. The noise is calculated starting from a description in frequency domain. Then an algorithm creates narrow band spectra with optimized behavior in time domain. Frequency domain data is transformed to time domain, and the amplitude is smoothed. The smoothed data is transformed back to frequency domain, and the spectral shape is restored. This process repeats until the amplitude in time domain has converged, while the desired spectrum shape is preserved. Noise generated in this way can be tailored for different requirements. We show the signal properties, the hardware, and preliminary beam test results, when the noise is applied to the MR RF system.
USTC/PMPI, Hefei, Anhui
USTC/NSRL, Hefei, Anhui
Collinear load is a substitute for waveguide load to miniaturize irradiation accelerators and make the system compact. The key technology is to design coaxial cavities coated inside with attenuating materials which will terminate the remnant power, meanwhile the operation frequency of 2856 MHz retains. For lossy materials such as Kanthal (25%Cr-5%Al-Fe) alloy, CST is used to simulate the effect of the coating on the load cavity properties like the operation frequency and attenuation. The frequency shifts caused by the coatings would be compensated by the strategy of cavity dimensions adjustment. Simulations revealed the compensation rules of the cavity inner radius b. Meanwhile the relationship between the attenuation and the coating area was also resolved. Based on a specified power allocation, a 15 kW collinear load consisting of six cavities at 2π/3 mode was designed with one-way attenuation of -18.8 dB. Two sets of prototype cavities have been manufactured and the experiment results are presented, compared with the CST simulations.
USTC/PMPI, Hefei, Anhui
USTC/NSRL, Hefei, Anhui
Microwave-absorbing material is an essential part of LINAC collinear load. It is coated on the inner walls of several trailing accelerating cavities to transform the remnant microwave power into heat. Fe-85%Si-9.6%Al-5.4% alloy, which reveals low outgassing rate and high attenuation, is selected for collinear load R&D. To measure the permittivity and permeability of FeSiAl at 2856 MHz, the coaxial transmission-reflection method is adopted. The system is firstly examined by testing the hollow coaxial fixture and comparing the results with the electromagnetic parameters of the air. Measurements of two PTFE rings show that the air gaps between the fixture and samples influence the test results seriously. CST is utilized to simulate the effects on the FeSiAl measure-ments. Eventually a scheme of molding the samples of FeSiAl powder mixed with paraffin to form a wax mold is proposed and the permittivity and permeability of FeSiAl are derived from the electromagnetic parameters equivalent formulas of mixed medium.
CERN, Geneva
DESY, Hamburg
The Super Proton Synchrotron (SPS) at CERN with a peak energy of 450GeV is at the top of the LHC preaccelerator-complex. Apart from the LHC, SPS is with Tevatron the accelerator with the largest stored beam energy of up to 2.5MJ. The SPS has a known vulnerability to fast equipment failures that led to an uncontrolled loss of a high intensity beam in 2008, which resulted in major damage of a main dipole. The beam loss was caused by a fast tune decrease towards an integer resonance. Simulations and distinct experimental studies provide clear understanding of the beam dynamics at different SPS tune resonances. Diverging closed orbit oscillations, dispersion explosion and increased beta-beating are the driving effects that lead to a complete beam loss in as little as 3 turns (70μs). Dedicated experiments of fast failures of the main power converters reveal that the current interlock systems are much too slow for an adequate machine protection. To counteract the vulnerability of the SPS, current research focuses on a new fast position interlock system which is planned to become operational in 2010.
GSI, Darmstadt
CERN, Geneva
The presence of an electron cloud in an accelerator generates a number of interesting phenomena. In addition to electron-driven beam instabilities, the electron "pinch" occurring during a beam-bunch passage gives rise to a highly nonlinear force experienced by individual beam particles. A simple 1-dimensional model for the effect of the electron pinch on the beam reveals a surprisingly rich dynamics. We present the model and discuss simulation results.
SLAC, Menlo Park, California
The Phase II upgrade to the LHC collimation system calls for complementing the 30 high robust Phase I graphite secondary collimators with 30 high Z Phase II collimators. This paper reports on BPM and impedance considerations and measurements of the integrated BPMs in the prototype rotatable collimator to be installed in the Super Proton Synchrotron (SPS) at CERN. The BPMs are necessary to align the jaws with the beam. Without careful design the beam impedance can result in unacceptable heating of the chamber wall or beam instabilities. The impedance measurements involve utilizing both a single displaced wire and two wires excited in opposite phase to disentangle the driving and detuning transverse impedances. Trapped mode resonances and longitudinal impedance are to also be measured and compared with simulations. These measurements, when completed, will demonstrate the device is fully operational and has the impedance characteristics and BPM performance acceptable for installation in the SPS.
Muroran Institute of Technology, Department of Electrical and Electronic Engineering, Muroran
TEMF, TU Darmstadt, Darmstadt
A Time Domain Boundary Element Method (TDBEM) has advantages of grid dispersion free property, treatment of electron bunch with curved trajectory, etc. in wake field analysis. On the other hand, the TDBEM has also serious problems of heavy calculation cost and large required memory which are main reasons why the TDBEM can not be widely used yet. For the large memory problem, moving window scheme was introduced into the TDBEM and it was shown that the TDBEM can be applied to very long accelerator structures*. This paper presents a new formulation of the TDBEM, an initial value problem formulation. To use the initial value problem formulation of the TDBEM, a new type of moving window scheme, which can be applied to curved trajectory or electron motion with smaller velocity than the speed of light, will be introduced.
* K.Fujita, H.Kawaguchi, R.Hampel, W.F.O.Muller, T.Weiland, S.Tomioka,"Time Domain Boundary Element Analysis of Wake Fields in Long Accelerator Structures,"IEEE Trans. Nucl. Sci.,55[5](2008),pp.2584-2591.
PSI, Villigen
IFH, Zurich
Laser induced field emission has become an enabling technology for building ultra-low emittance electron sources for particle accelerators, such as the x-ray free-electron laser (SwissFEL) under development at the Paul Scherrer Institut (PSI). One approach consists of a sharp pyramidal tip with lateral dimensions of a few nanometers, illuminated by a laser to increase the extracted electron current. Another approaches uses conventional cathodes. In both cases, there are structural details on the nanometer scale, that determine the interaction between the laser and the cathode and thus directly the quantum efficiency of the emitter. We use a 3-d full-wave finite element time domain electromagnetic approach* to understand the nano-optical interaction between structure and laser pulse. For example, the lightning rod effect of sharp tips enhances the electric field in the vicinity. Also, optical antenna concepts have been proposed to enhance the electric field at the field emitter's tip so that higher currents can be extracted. We use dispersive material models for the metals in the optical region of the electromagnetic spectrum.
*Benedikt Oswald and Patrick Leidenberger, Journal of Computational and Theoretical Nanoscience, Vol 6(3), 2009, pp. 784-794. doi 10.1166/jctn.2009.1109
CASA, newport news
JLAB, Newport News, Virginia
One key limiting factor to a collider luminosity is bean-beam interactions which usually can cause serious emittance growth of colliding beams and fast reduction of luminosity. Such nonlinear collective beam effect can be a very serious design challenge when the machine parameters are pushed into a new regime. In this paper, we present simulation studies of the beam-beam effect for a medium energy ring-ring electron-ion collider based on CEBAF.
KEK, Ibaraki
J-PARC, KEK & JAEA, Ibaraki-ken
During the early J-PARC Main Ring commissioning and the machine operation with the moderate beam power the 'fast extraction' bare working point has been chosen to provide the machine operation in the safe regime. We discuss main experimental results obtained so far and compare with the results of the computational model of the machine, including the first experimental approach to minimize the effect of the 'sum' linear coupling resonance. The strategy to increase the beam power without changing the operational working point is presented by keeping the moderate space-charge detuning. The advantage of the second harmonic MR RF cavity, including the estimation of the beam losses during the injection and acceleration processes, is discussed.
Northern Illinois University, DeKalb, Illinois
ANL, Argonne
This research involves a method for combining the intricate diagnostic tools for calculating quantities of interest such as tunes, dispersion and resonances from the single particle map of the system, with an accurate approximation of space charge effects on the beam. The space charge calculation involves a novel method of potential integration which allows for rapid Taylor expansion around singularities. This will allow for an accurate computation of space charge induced tune shifts and resonances, as well as allowing for experimental setups to discriminate between space charge caused issues, and lattice caused issues. The code used was COSY Infinity 9.0 which uses Differential Algebras to determine numerical derivatives to arbitrary order, and Normal Form methods to extract information from the map. The effects of space charge are added to the map using Strang splitting. External confounding factors such as the earths magnetic field are also addressed.
CLASSE, Ithaca, New York
Cornell University, Ithaca, New York
LBNL, Berkeley, California
ANL, Argonne
Retarding field analyzers (RFAs) provide an effective measure of the local electron cloud density and energy distribution. Proper interpretation of RFA data can yield information about the behavior of the cloud, as well as the surface properties of the instrumented vacuum chamber. However, due to the complex interaction of the cloud with the RFA, particularly in regions of high magnetic field, understanding these measurements can be nontrivial. This paper will examine different methods for interpreting RFA data via cloud simulation programs. Possible techniques include postprocessing the output of a simulation code to predict the RFA response, and incorporating an RFA model into the program itself.
ELETTRA, Basovizza
FERMI@ELETTRA is a single pass FEL Facility in construction at the ELETTRA Laboratory in Trieste. To linearize the beam longitudinal phase space, it is planned to use a short X-band accelerating structure installed before the first bunch compressor. Since both the end tubes of the structure have a reduced radius of 5.0 mm, much smaller than the 13.5 mm radius of the beam pipes before and after the structure, a transition, either stepped or tapered, will be necessary between the two components. Using the ABCI code, we have investigated the short range wake fields at the step-out and taper-out transitions and we have compared them with some conventional analytical models. We have developed specific ABCI-based analytical models that simulate accurately the short range wake field for a wide range of rms bunch lengths (σ: 100 - 1000μm).
EPFL, Lausanne
CERN, Geneva
INFN/LNF, Frascati (Roma)
Honorary CERN Staff Member, Grand-Saconnex
The beam coupling impedance of the CERN SPS is expected to be one of the limitations to an intensity upgrade of the LHC complex. In order to be able to reduce the SPS impedance, its main contributors need to be identified. An impedance model for the SPS has been gathered from theoretical calculations, electromagnetic simulations and bench measurements of single SPS elements. The current model accounts for the longitudinal and transverse impedance of the kickers, the horizontal and vertical electrostatic beam position monitors, the RF cavities and the 6.7 km beam pipe. In order to assess the validity of this model, macroparticle simulations of a bunch interacting with this updated SPS impedance model are compared to measurements performed with the SPS beam.
GSI, Darmstadt
CERN, Geneva
The measurement of synchrotron nonlinear components is an essential step for devising an effective compensation scheme for improving machine performances. A validation test of a recently proposed method called nonlinear tune response matrix (NTRM) for measuring circular accelerator nonlinear components is undergoing in a CERN-GSI joint effort. The test consists in the attempt of reconstructing few controlled octupolar components in the SPS synchrotron. In this proceeding we report on the SPS benchmarking experiment and discuss the performances the NTRM method applied to this measurements.
Monash University, Faculty of Science, Victoria
ASCo, Clayton, Victoria
The Australian Synchrotron booster synchrotron accelerates electrons from 100 MeV to 3 GeV in 600 ms. The fractional tune components that were measured are presented in two graphical formats showing the time-resolved measurement of the horizontal and vertical tunes. This experiment demonstrated that the current in the booster was extremely sensitive to the ratio of BF to BD combined-function magnets. Large variations of the fractional tunes were found to follow the differences in the gradients of the BD and BF combined-function magnet ramping curves and with this knowledge, alterations were made to the ramping table increasing the efficiency of the booster by on average 40%. Rapid fluctuation of the tunes meant that it could not be distinguished during the first 80ms of the ramp. Multiple side bands to the revolution harmonic were visible during a minimal sweep time of 2.5ms, during this first 80ms.
SOLEIL, Gif-sur-Yvette
SOLEIL is the French 2.75 GeV high brilliance third generation synchrotron light source delivering photons to 20 beamlines with a current of 400 mA in multibunch or hybrid modes, and 60 mA in 8 bunch mode. There are already 17 insertion devices installed and 9 others are planned in the next 2 coming years. Among them, two canted in vacuum insertion devices are planned, for the Nanoscopium and Tomography beamlines, and will be accommodated in a 12 m long straight section, with a 6.5 mrad separation angle. These ~150 m long beamlines will exploit the high brilliance and coherence characteristics of the X-ray (5-20 keV) beam both for diffraction limited focusing and for contrast formation. To provide low vertical beta functions at each undulator, an extra triplet of quadrupoles was added in the middle of the section. We present here the lattice implementation footprint, the different working point under investigations as well as the first results of the measurements on the machine performances.
DESY, Hamburg
JAI, Oxford
PETRA III is a 3rd generation synchrotron radiation light source which started commissioning in April 2009. Turn-by-turn capabilities are available for all 227 BPMs installed in the storage ring thus providing a powerful diagnostic tool for the characterization of the linear and nonlinear motion of the stored beam. We report on first results of beam dynamics studies using multiturn data acquired at PETRA III and first steps towards a calibration of the linear and nonlinear lattice model of the storage ring.
Diamond, Oxfordshire
Diamond Light Source has delivered beam for users exclusively in top-up mode since the end of October 2008. In this mode, a small number of single bunches are injected into specific buckets of the storage ring every ten minutes in order to maintain a constant beam current and fill pattern. During top-up the storage ring current is held within a window of approximately 1.5mA around the target current, generally 250mA, for a variety of fill patterns, including a two-thirds storage ring fill and a hybrid fill in which an intense single bunch is added to the normal fill pattern. Top-up has run continuously for several days on many occasions, with injection efficiency into the storage ring of typically 60%-95% even with 10 in-vacuum insertion device in operation with a permitted minimum gap of 5 mm. The effect of insertion devices, pulsed magnet stability and storage ring beam optics on top-up reliability and performance is examined, and the development of tools for the control of top-up and storage ring fill is detailed.
BNL, Upton, Long Island, New York
Chromaticity is usually set to non-zero value at the third generation light sources to cure the intensity induced instabilities. It is effective in suppressing the beam centroid oscillation; however, it is repeatedly reported that the beam lifetime decreases significantly when chromaticity goes up. This is probably due to the crossing of resonance lines by the enlarged tune footprint. In this paper we optimize the NSLS-II lattice at different positive chromaticity settings. The tune footprint is adjusted to fit in the stable region divided by the strong resonance lines. Tracking results show that we can maintain a lifetime similar to that of the zero-chromaticity lattice solutions.
J-PARC, KEK & JAEA, Ibaraki-ken
JAEA/J-PARC, Tokai-mura
KEK, Ibaraki
In the J-PARC Main Ring (MR), the bending, quadrupole, sextupole, and steering magnets can be controlled on the operating interfaces (OPI). The optics parameters for all magnets are calculated by using SAD, and are converted to BL tables (ex: 2000 points for a steering magnet) for each power supplies. The BL tables are made from the parameters of optics, pattern timing, and beam energy at flat bottom and flat top. For MR beam studies, the BL tables are adjustable with offset and factor. This system is useful for COD correction, beta function measurement, aperture survey, and slow extraction. In this proceeding, the structure of the magnet control system and OPIs for beam studies will be shown.
CERN, Geneva
A prerequisite for a successful nanometre level magnet stabilization and pointing system is a low background vibration level. This paper will summarize and compare the ground motion measurements made recently in different accelerator environments at e.g. CERN, CESRTA and PSI. Furthermore the paper will give the beginning of an inventory and characterization of some technical noise sources, and their propagation and influence in an accelerator environment. The importance of the magnet support is also mentioned. Finally, some advances in the characterization of the nanometre vibration measurement techniques will be given.
MPI-K, Heidelberg
UMD, College Park, Maryland
Cockcroft Institute, Warrington, Cheshire
Beam halo can have severe effects on the performance of high energy accelerators. It reduces the experimental throughput, may lead to noise in the experiments, or even damaging of accelerator components. In order to understand and ideally control the formation and evolution of beam halo, detailed simulation studies are required. In this contribution halo generation mechanisms and the underlying physical principles are first presented, before the particular case of the CLIC Test Facility (CTF3) is discussed in detail. Analytical, numerical and simulation studies are combined to estimate the relevant sources of halo formation and to study halo propagation in the different CTF3 sections.
Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Elektronen-Speicherring BESSY II, Berlin
The HoBiCaT facility has been has been set-up and operated at the Helmholtz-Zentrum-Berlin and BESSY since 2005. Its purpose is testing superconducting cavities horizontally in CW mode of operation and it was successfully demonstrated, that TESLA pulsed technology can be used for CW mode of operation with only minor changes. A specific topic is addressed in this paper: elevated dynamic thermal losses in the cavity walls due to trapped magnetic flux.
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock
Beam energy deposited in Higher-Order-Modes may affect both beam stability and cryo power requirements of the planned CERN Superconducting Proton Linac SPL. We report on numerical studies of the high-beta cavity type, analyzing it's HOM spectrum. The most dangerous modes are identified and different possibilities of appropriate damping are discussed.
KEK, Ibaraki
ISSP/SRL, Chiba
JAEA/ERL, Ibaraki
We started to develop an input power coupler for a 1.3GHz ERL superconducting cavity for ERL main linac. Required input power is about 20kW for the cavity acceleration field of 20MV/m and the beam current of 100mA in energy recovery operation. The input coupler is designed based on the STF-BL input coupler, especially choke-mode type ceramic window was applied. After that some modifications are applied for the CW 20kW power operation. We fabricated input coupler components such as ceramic windows and bellows and carried out the high-power test of the components by using a 30kW IOT power source and a test stand constructed.
KEK, Ibaraki
JAEA/ERL, Ibaraki
ISSP/SRL, Chiba
The coaxial-type input couplers are frequently used for accelerators, since it can successfully propagate high power of RF. Thus we have been developing the coaxial-type input coupler for ERL main linac, operated at 1.3 GHz. When performing high power test of its component, however, we suffered from the heat load due to unexpected loss. A resonance just around 1.3 GHz was found from the low-level measurement. In order to investigate the cause of that resonance, precise calculation was done with MW-studio and HFSS codes. Both codes showed one of dipole modes exists at around 1.3 GHz, near coaxial ceramic window. Details of the mode were further investigated. It showed that the resonant frequency of it depends on, for example, the thickness of the ceramic, the permittivity of the ceramic, and the sizes of inner and outer conductors. In this report, we summarize the experimental observations and the some results from the calculations.
PKU/IHIP, Beijing
Peking University, School of Physics, Beijing
Spoke cavities have been developed and have apparent advantages for high current proton accelerator based on superconductivity at low and medium energy region. As the research and the technical reserve, Peking University has started the R&D program of single spoke cavity (SSC). The work is proposed to do beam load experiment on the HI-13 Tandem at CIAE. The maximum kinetic energy of proton beam is 26MeV, and the frequency of the chopper for superconducting is 150MHz. It leads us to the choice of a 450MHz and β=0.2 single spoke cavity. In this paper, the RF design, mechanical study, fabrication arts, tolerance analysis, and room temperature RF test is presented.
CLASSE, Ithaca, New York
The high magnetic and electric radio-frequency fields in superconducting microwave cavities cause heating of the inner cavity surface and generate Lorentz-forces, which deform the shape of the cavity and thereby result in a shift of the fundamental mode frequency. 3-dimensional numerical codes can create complex coupled simulations of the electromagnetic fields excited in a cavity, of heat dissipation and heat transfer, as well as of mechanical effects. In this paper we summarize our simulation results using the engineering simulation package ANSYS.
NSRRC, Hsinchu
The purpose of this paper is to estimate the conductive Electromagnetic Interference (EMI) from magnet power supply in NSRRC. A LISN system was conducted to measure the EMI spectrum of power supply. The different frequency range of conductive EMI was measured. For the future TPS(Taiwan Photon Source) power supply design, the EMI signals must be lower than TLS kicker. Therefore reducing and eliminating the interference of electromagnetic waves will be a very important issue. A filter and shielding method were used to test the effects of reducing EMI. The EMI prevention scheme will be used in the future.
Fermilab, Batavia
Muons, Inc, Batavia
IIT, Chicago, Illinois
ANL, Argonne
University of Chicago, Chicago, Illinois
Voss Scientific, Albuquerque, New Mexico
A high pressurizing hydrogen gas filled RF cavity has a great potential to apply for muon colliders. It generates high electric field gradients in strong magnetic fields with various conditions. As the remaining demonstration, it must work under high radiation conditions. A high intensity muon beam will generate a beam-induced electron swarm via the ionization process in the cavity. A large amount of RF power will be consumed into the swarm. We show the recent non-beam test and discuss the electron swarm dynamics which plays a key role to develop a high pressure RF cavity.
STFC/RAL, Chilton, Didcot, Oxon
EMMA is the world's first non-scaling fixed field alternating gradient accelerator and is being constructed at the STFC Daresbury Laboratory. Experience from the initial commissioning phases (from early 2010) will be reported and lessons for future machines of a similar type will be discussed. The present experimental status and future plans will also be reported.
CERN, Geneva
ESRF, Grenoble
Following the analysis of the results obtained during the first year of beam commissioning of the CERN multi-turn extraction, a number of changes have been introduced in the beam manipulations performed in the CERN Proton Synchrotron. This includes a different control of the linear chromaticity, the setting of the non-linear magnets used to split the beam, and the longitudinal structure in the PS. The results obtained during the 2009 run are presented and discussed in detail, including the beam performance in both the PS and the SPS, as well as the optics measurements in the transfer line between the two circular machines.
BNL, Upton, Long Island, New York
High energy polarized proton beams are desired for exploring the proton spin structure as well as other spin dependent measurements. However, depolarizing mechanisms due to the interaction between the spin motion and the magnetic fields challenges accelerating polarized protons to high energy in circular accelerators. Several decades of efforts in developing techniques to preserve polarization to high energy have finally led to the success of the polarized proton program at the Brookhaven Relativistic Heavy Ion Collider (RHIC). Designed to provide polarized proton collisions up to 250GeV, RHIC is equipped with two Siberian snakes to avoid both intrinsic and imperfection depolarizing resonances. Currently, polarization has been preserved up to 100 GeV at RHIC with precise control of orbit and betatron tunes. The polarized protons were first brought into collisions at 250GeV in RHIC in 2009, and depolarizations were observed between 100 GeV to 250 GeV. This presentation reports the progress of RHIC polarized proton program. Strategies of how to preserve the polarization through the RHIC injectors are also presented.
CERN, Geneva
I will briefly describe CERN's colliders starting with the ISR, going through LEP, and finishing with the LHC. The common threads will be discussed in terms of people and techniques. I will start by describing the incredible impact on accelerator physics of the almost forgotten, first ever hadron collider, the ISR. I will then present the construction and 12 years of operation of LEP. Finally I will also provide the first results of beam operation in the LHC as well as the plans for the near and far future.
KEK, Ibaraki
JAEA/J-PARC, Tokai-mura
The RF cavity using Magnetic Alloy (MA) cores has been developed for achieving the high field gradient in J-PARC. For reducing the beam loading effects, the Q-value of the RF cavities in the Main Ring (MR) is controlled by using the cut-core configuration. In order to check the effect of HOMs between the cut-core gap, a simulation method of MA cores was studied and electromagnetic fields of excitation modes have been calculated by HFSS. We present the detail of the simulation method of MA cores and the HOM analysis of the cavity with the cut-cores.
KEK, Ibaraki
A waveguide vacuum valve for WR90 waveguide was designed, fabricated and tested. The valve consists of a modified commercial gate valve sandwitched with smooth tapers. The TE10 traveling wave in WR90 waveguide is "transmoded" into TE11+TM11 mode in the taper, going through the gate valve and is tapered back to the normal mode in WR90. The test has been successfully done. The valve stably trasmitted 40MW peak power with 500ns pulse width and this is limited by available RF power source.
KEK, Ibaraki
BNL, Upton, Long Island, New York
An RF system using Magnetic Alloy is considered as an option to study the beam dynamics of a linear non-scaling FFAG. Such an FFAG may have many resonances, which affect the beam more when the beam crosses them slowly. The RF system aims at ordinary RF bucket acceleration with an RF frequency sweep of 3 % in 100 turns. The cavity has only 10 cm length to fit in a short straight section. The required RF voltage is 100 kV per turn and each of the three cavities is designed to generate 50 kV.
BINP SB RAS, Novosibirsk
ICKC, Novosibirsk
ICKC SB RAS, Novosibirsk
The prototype of parallel coupled accelerating structure is developed. It consists of five accelerating cavities, common excitation cavity and RF power waveguide feeder. The excitation cavity is a segment of rectangular waveguide loaded by resonance copper pins. The excitation cavity operate mode is T 105. Connection between excitation cavity and accelerating cavities is performed by magnetic field. The theoretical model of the parallel coupled accelerating structure is developed. According to model the tuning and matching of the structure are performed. The electrodynamics characteristics are measured. In storage energy regime the accelerated electron beam is obtained.
ANL, Argonne
Euclid TechLabs, LLC, Solon, Ohio
As the dimensions of accelerating structures become smaller and beam intensities higher, the transverse wakefields driven by the beam become quite large with even a slight misalignment of the beam. These deflection modes can cause inter-bunch beam breakup and intra-bunch head-tail instabilities along the beam path. We propose a built-in tunable absorption mechanism for damping the parasitic transverse modes without affecting the operational modes in dielectric loaded accelerating (DLA) structures and wakefield power extractors. The new principle for HOM absorption is based on electron paramagnetic resonance. The dielectric tube of the DLA has to be doped with a material exhibiting high EPR, for example ruby, Al2O3 overdoped ~1% with Cr3+. The absorption frequency can be tuned by an external DC magnetic field to match the frequency of the transverse mode. At the resonance imaginary part of permeability becomes significant and the dielectric tube acts as an absorber for the transverse modes. The external DC magnetic field is solenoidal and has to have a magnitude of about 3 kG. This configuration in fact is desirable to focus the beam and provide additional control of beam break up.
SLAC, Menlo Park, California
SLAC participates in the U.S. High Gradient collaboration whose charter includes basic studies of rf breakdown properties in accelerating structures. These studies include experiments with different materials and construction methods for single cell standing wave accelerating structures. The most commonly used method of joining cells of such structures is the high temperature bonding and/or brazing in hydrogen and/or vacuum. These high temperature processes may not be suitable for some of the new materials that are under consideration. We propose to build structures from cells with an rf choke, taking the cell-to-cell junction out of the electromagnetic field region. These cells will be clamped together in a vacuum enclosure, the choke joint ensuring continuity of rf currents. Next, we propose a structure with a choke joint in a high gradient cell and a view port which may allow us microscopic, in-situ observation of the metal surface during high power tests. And third, we describe the design of a TM01 choke flange for these structures.
GSI, Darmstadt
ITEP, Moscow
The heavy ion synchrotron SIS-100 will play a key role within the future FAIR project underway at GSI. Although this synchrotron is optimized for fast extraction, also slow extraction will be used. Slow extraction is based on beam excitation due to a third order resonance. The spread in the particle momenta generating a tune spread causes particle loss leading to an irradiation of the machine especially in a high-current operation. A major part of the losses is assumed to occur at the electro-static separator. In the present study we apply a tracking method to model the extraction process to predict the losses, where, in a first step, high current effects are not taken into account.
GSI, Darmstadt
IAP, Frankfurt am Main
With the ability to accelerate heavy ions up to an energy of 32 GeV/u, the SIS300 superconducting (sc) synchrotron is a central part of the new FAIR facility at GSI-Darmstadt. SIS300 will provide beams with a 20-fold increase in energy and, by means of a stretcher mode or a fast ramped mode (1 T/s), 100-10000 times higher average intensity. The beam from SIS300 will be extracted towards the experiments using resonant slow extraction, thus SIS300 becomes the first superconducting synchrotron worldwide with this feature. Coupling and persistent currents are the main practical limitation for operation of sc magnets at high ramping rates and long slow extraction plateaus. The effect of the persistent currents, which are time dependent and depend as well on the magnet's history, is especially critical for slow extraction at low energies. These effects determine the tolerances on magnetic components. In order to address this issue, detailed simulations of beam dynamics at slow extraction have been performed. In particular, the optimization of the lattice and its optical parameters for a low-loss extraction in the presence of steady and time-dependent field components will be presented.
NIRS, Chiba-shi
The betatron tune fluctuation due to the current ripple of power supplies brings the beam spill ripple through the stable area variation in resonant slow extraction. The effect becomes dominant especially in the case of the low beam rate extraction. The RF-knockout slow extraction method is insensitive to the tune ripple compared to the ordinary one because it uses the diffusion with the transverse RF field. However, the ripple effect appears even in the beam spill extracted by it. The amount of the separatrix fluctuation due to the tune ripple depends on the difference between the bare and the resonant tune, and the sextupole magnetic strength. We measured the correlation between the beam spill and the tune ripple which was the artificially generated with low and high frequency components of 67 Hz and 1167 Hz near those of the real current ripple. We confirmed the reduction of the beam spill ripple by setting the tune away from the resonance while keeping the separatrix area. The comparison between the experimental results, the analytical calculation and the simulation will be reported.
Fermilab, Batavia
Muons, Inc, Batavia
Typically, high power sources for accelerator applications are multi-megawatt microwave tubes that may be combined together to form ultra-high-power localized power stations. The RF power is then distributed to multiple strings of cavities through high power waveguide systems which are problematic in terms of expense, efficiency, and reliability. Magnetrons are the lowest cost microwave source in dollars/kW, and they have the highest efficiency (typically greater than 85%). However, the frequency stability and phase stability of magnetrons are not adequate, when magnetrons are used as power sources for accelerators. Novel variable frequency cavity techniques have been developed which will be utilized to phase and frequency lock magnetrons, allowing their use for either individual cavities, or cavity strings. Ferrite or YIG (Yttrium Iron Garnet) materials will be attached in the regions of high magnetic field of radial-vaned, π−mode structures of a selected ordinary magnetron. A variable external magnetic field that is orthogonal to the magnetic RF field of the magnetron will surround the magnetron to vary the permeability of the ferrite or YIG material.
Siemens AG, Healthcare Technology and Concepts, Erlangen
The concept of a compact particle accelerator capable of delivering accelerating fields upto 100MV/m using a direct drive RF LINAC is explored. Such a machine consists of a succession of RF cavities with the RF power being supplied from a ring of solid state RF transistors placed around the cavity circumference. To achieve the required accelerating fields 3 core technologies are presented. (i) The solid-state transistors are used to drive the wall currents in the cavities so achieving a direct drive of the cavity. This allows unprecedented powers to be reached (>GW class) as well as enabling independent phase control of the individual cavities. Central to the implementation is the design of the RF drive consisting of distributed SiC vJFET modules delivering 750kA at 800V per cavity. (ii) A High Gradient Insulator structure is required to hold an electric field of >100MV/m. In contrast to a conventional HGI, the concept utilizes a vacuum insulated grading layer structure. (iii) A chopper and injection system allow the formation of proton bunches with a spatial emissivity <3ns and an injection field of up to 100MV/m.
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
JAI, Oxford
EMMA - the Electron Model of Many Applications - is to be built at the STFC Daresbury Laboratory in the UK and will be the first non-scaling FFAG ever constructed. The purpose of EMMA is to study beam dynamics in such an accelerator. The EMMA orbit correction scheme must deal with two characteristics of a non-scaling FFAG: i.e. the lack of a well defined reference orbit and the variation with momentum of the phase advance between lattice elements. In this study we present a novel orbit correction scheme that avoids the former problem by instead aiming to maximise both the symmetry of the orbit and the physical aperture of the beam. The latter problem is dealt with by optimising the corrector strengths over the energy range.
UCLA, Los Angeles
PBPL, Los Angeles
Manhattanville College, Purchase, New York
This paper extends the physics of the Micro-Accelerator Platform (MAP), which is in development as an optical structure for laser acceleration of relativistic electrons. The MAP is a resonant, optical-scale, slab-symmetric device that is fabricated from dielectric materials using layer-deposition techniques. For stand-alone applications, low-energy electrons (beta ~ 0.3) must be synchronously accelerated to relativistic speeds for injection into the MAP. Even lower energies are desired for other particle species (e.g. protons or muons). In this paper, we present design and simulation studies on a tapered geometry and associated coupling scheme that can produce synchronous acceleration at beta < 1 within a MAP-like structure.
USTC/NSRL, Hefei, Anhui
A brief, but clear, review of beam polarization theory is given in the paper. Particularly, the algorithm of spin linear transfer matrix (SLIM) is applied to remark the situation of beam in storage ring, specific to HLS (Hefei Light Source). Theoretical analysis indicates that the beam in HLS, working at 800MeV and 2.58/3.58 transverse tunes, could keep away from a variety of spin resonances, and should be able to build up high polarization.
Kyungpook National University, Daegu
Proton Engineering Frontier Project (PEFP) Linac has a plan of the addition of 1 GeV RCS ring. The lattice of the rapid cycling synchrotron is affected by a non-linear beam dynamics. In this study, we investigated about non-linear dynamics due to sextupoles in PEFP RCS. Notably, we investigated about 3rd integer resonance due to sextupoles. To slowly and continuously extract the proton beam, we utilize the 3rd integer resonance. For the reason, we investigated non linear beam dynamics due to 3rd integer resonance and slow extraction system by using of MAD8.
PAL, Pohang, Kyungbuk
SINAP, Shanghai
The measurement and the control of the coupling is essential to maximize synchrotron performance. Small coupling is required for small vertical size and high brightness. The Pohang Light Source has a 2.5 GeV storage ring and its coupling constant is measured as about 1%. In addition to errors at quadrupole or sextupole, the condition varying of the insertion device affects the coupling. The coupling for various condition is measured by the resonance and the response matrix and compared with the beam size and the lifetime. The correction and the control of the coupling is presented.
CERN, Geneva
FZJ, Jülich
The PS2 ring is designed with negative momentum compaction arc cells and doublet straights. In this paper, different lattice geometries are considered. In particular, a two-fold symmetric lattice with dispersion suppressors and a 3-fold symmetric one with resonant arc cells are compared with respect to their optics properties, and ability to satisfy space and magnet constraints. The tuning flexibility of rings based on these two options is presented. Finally, the impact of different geometries on resonance excitation and dynamic aperture is evaluated.
CERN, Geneva
BNL, Upton, Long Island, New York
Consolidation of the coupling correction scheme in the LHC is motivated due to a missing skew quadrupole family in Sector 3-4 at the start-up in 2009. Simultaneous coupling and vertical dispersion correction using vertical orbit bumps at the sextupoles, was studied by analyzing turn-by-turn data. This scheme was tested in SPS where the optical structure of arc cells is quite similar to the LHC. In SPS, horizontal and vertical beam positions are measured separately with single plane BPMs, thus a technique to construct "pseudo double plane BPM" is also discussed.
CERN, Geneva
BNL, Upton, Long Island, New York
After the incident in the LHC in 2008, few skew quadrupoles were damaged and subsequently removed from the tunnel. This could limit the correction of local coupling in the LHC. In order to increase the flexibility in the coupling correction it has been proposed to use of vertical orbit bumps at the sextupoles is studied. Moreover a simultaneous coupling and vertical dispersion can be implemented. Various studies are presented addressing the optimal approach for the correction of the vertical dispersion and the sum and difference coupling resonances.
CERN, Geneva
BNL, Upton, Long Island, New York
A software package has been developed for the LHC on-line optics measurement and correction. This package includes several different algorithms to measure phase advance, beta functions, dispersion, coupling parameters and even some non-linear terms. A Graphical User Interface provides visualization tools to compare measurements to model predictions, fit analytical formula, localize error sources and compute and send corrections to the hardware.
CLASSE, Ithaca, New York
We are developing techniques for measuring and correcting emittance diluting optical and alignment errors in the CesrTA storage ring. Our principle measurement method is to resonantly excite the beam at all three normal mode frequencies and then to extract the amplitude and phase of each mode at all 100 beam position monitors. We reconstruct beta-functions, betatron phase advance, coupling parameters, dispersion, and BPM tilts from the data. A complete characterization including data collection and analysis can be done in a few minutes. To measure the emittance, an x-ray beam size monitor capable of measuring the size of a single bunch on a turn by turn basis provides a real time measure with a resolution on the order of a few microns. This resolution corresponds to a few pm emittance. Our ability to identify alignment and optical errors is limited by systematic measurement errors. We report on the status of our efforts to understand and eliminate systematic errors, the accuracy of our characterization of the machine optics, and our success at reducing sources of emittance dilution.
BNL, Upton, Long Island, New York
Polarized proton beams are accelerated in RHIC to 250 GeV energy with the help of Siberian Snakes. The pair of Siberian Snakes in each RHIC ring holds the design spin tune at 1/2 to avoid polarization loss during acceleration. However, in the presence of closed orbit errors, the actual spin tune can be shifted from the exact 1/2 value. It leads to corresponding shift of locations of higher-order ("Snake") resonances and limits available betatron tune space. The largest closed orbit effect on the spin tune comes from the horizontal orbit angle between the two snakes. During RHIC Run in 2009 dedicated measurements with polarized proton beams were taken to verify the dependence of the spin tune on the local orbits at the Snakes. The experimental results are presented along with the comparison with analytical predictions.
SOLEIL, Gif-sur-Yvette
SOLEIL, the French 2.75 GeV high brilliance third generation synchrotron light source is delivering photons to 20 beam lines and is presently equipped with 17 insertion devices. Significant reduction of injection efficiency and beam lifetime are observed when using some undulator configurations in daily operation. Measurements on electron beam, such as beam lifetime versus RF voltage, have shown that the energy acceptance is strongly reduced by the combined non linear effects of the four U20 in-vacuum undulators and the HU640 10m long undulator used in linear vertical polarization mode. This paper will present the on and off momentum frequency map measurements that have been performed in order to investigate such effects. The reduction of the on momentum dynamic aperture in the presence of the U20 undulators is confirmed. The off momentum frequency map measurements confirm that the energy acceptance of the bare machine is very large as predicted by tracking calculations, and clearly exhibit the strong energy acceptance reduction due to undulators.
FZJ, Jülich
The High-Energy Storage Ring (HESR) is part of the upcoming Facility for Antiproton and Ion Research (FAIR). The HESR will provide antiprotons in the momentum range from 1.5 to 15 GeV/c for the internal target experiment PANDA. The demanding requirements of PANDA in terms of beam quality and luminosity together with a limited production rate of antiprotons call for a long beam life time and a minimum of beam loss. Thus, a sufficiently large dynamic aperture of the HESR is crucial. To provide this, a chromaticity correction scheme for the HESR has been developed to reduce tune spread and thus to minimize the emittance growth caused by betatron resonances. The chromaticity correction scheme has been optimized through dynamic aperture calculations. The estimated field errors of the HESR dipole and quadrupole magnets have been included in the non-linear beam dynamics studies. The ion optical settings of the HESR have been improved using dynamic aperture calculations and frequency map analysis technique. In this presentation comprehensive beam simulations are presented and predictions of long-term stability based on short-term particle tracking and orbit diffusion discussed.
HU/AdSM, Higashi-Hiroshima
LLNL, Livermore, California
Resonant instabilities of ion plasmas confined in a linear Paul trap are studied using the particle-in-cell code WARP. Transverse two-dimensional model is employed to save computing time and perform systematic investigations. Both applied and self-field forces are calculated with a boundary condition assuming a quadrupole electrode structure. A large number of simulations were carried out with rms matched plasmas to clarify characteristics of the instability caused by linear and nonlinear coherent resonances. Stop band distributions produced by the simulation runs are consistent with theoretical prediction. These results are also compared to experimental results obtained from Hiroshima University Paul trap that is developed to study beam dynamics. It is shown that the stop band distributions of both numerical and experimental results are good agreement each other. We confirmed from these results that coherent resonances are excited when one of the coherent tunes is close to a half integer.
KEK, Ibaraki
J-PARC, KEK & JAEA, Ibaraki-ken
During the early J-PARC Main Ring commissioning the emittance growth at the injection energy, caused by the field leakage of the slow extraction septums, has been observed. By using the measured field data in the J-PARC Main Ring computational model we perform the analysis of the resonance excitation for the 'bare' working points around the 3rd order horizontal resonance, used for the slow extraction of the accelerated beam. The space charge effects of the low energy beam with the moderate beam power are taken into this analysis. Some possible ways to reduce the transverse emittance dilution and the particle losses during the machine operation for the 'hadron' experiments are discussed.
KEK, Ibaraki
Synchro-beta resonances enhance beam sizes dynamically. For accelerators aimed for high luminosity, the effect can be more serious since a difference between vertical emittance and longitudinal emittance tends to be larger. Therefore, it is necessary to estimate a tune spread of the synchro-beta resonances properly. Synchro-beta effect is caused by chromatic aberrations, which characterize how optics parameters, including tune, Twiss parameter, X-Y coupling parameter, and other parameters, depend on the momentum deviation. The chromatic aberrations are actually defined by coefficients of an optics parameter in is expansion in terms of momentum deviation. The synchro-beta resonances caused by chromatic aberrations are discussed in this conference. We use 6-dimensional symplectic map which is obtained from measured optics parameters in order to simulate beam motion precisely*.
* Y. Seimiya and K. Ohmi, TH6PFP020, Particle Accelerator Conference PAC09, 4-8 May 2009, Vancouver, Canada.
PAL, Pohang, Kyungbuk
A superconducting RF cavity is used in the storage ring of the Pohang Light Source (PLS) upgrade project (PLS-II) at Pohang Accelerator Laboratory (PAL) for increasing the electron beam current and energy from 2.5GeV/200mA to 3.0GeV/400mA. In order to meet the requirement of lower beam emittance and higher photon energies, as well as more straight sections for insertion devices, the vacuum chambers in the storage ring need to be reconstructed. To control the spurious harmonic resonances' effect to beam position monitors (BPMs) in the PLS and PLS-II storage ring vacuum chamber, the TE mode distribution in vacuum chambers has been analyzed by both numerical simulation and experiment. Based on this analysis, the proper method to control the strength of TE mode at the position of BPMs is suggested.
BINP SB RAS, Novosibirsk
We applied Frequency Map Analysis (FMA) - a method that is widely used to explore dynamics of Hamiltonian systems - to beam-beam effects study. The method turned out to be rather informative and illustrative in case of a novel Crab Waist collision approach, when "crab" focusing of colliding beams results in significant suppression of betatron coupling resonances. Application of FMA provides visible information about all the working resonances, their widths and locations in the planes of betatron tunes and betatron amplitudes, so the process of resonances suppression due to the beams crabbing is clearly seen.
CERN, Geneva
ESRF, Grenoble
Recently, a novel multi-turn injection technique was proposed. It is based on beam merging via resonance crossing. The various beamlets are successively injected and merged back by crossing a stable resonance generated by non-linear magnetic fields. Space charge is usually a crucial effect at injection in a circular machine and it could have an adverse impact on the phase space topology required for merging the various beamlets. Numerical simulations were performed to assess the stability of the merging process as a function of injected beam charge. The results are presented and discussed in this paper.
Diamond, Oxfordshire
JAI, Oxford
Diamond operates with 10 in-vacuum insertion devices at 5 mm gap, two Apple-II, two superconducting and two normal conducting wigglers. We report here the correction of the linear optics of wigglers and measurements of nonlinear effects such as dynamic aperture and frequency maps and their impacts on injection efficiency, lifetime and loss distribution in operation of the storage ring.
MIT/PSFC, Cambridge, Massachusetts
The dynamics of charged particles in a recently-discovered adiabatic thermal beam equilibrium* are studied. In particular, test particle motion is analyzed numerically, assuming the beam equilibrium fields are in a periodic solenoidal focusing channel. Poincare surface-of-section maps are generated to examine the behavior of the test particles in phase space such as nonlinear resonances and chaotic regions. Comparisons are made between the adiabatic thermal and rigid-rotor Vlasov beam equilibria**.
* J. Zhou, K.R. Samokhvalova, and C. Chen, Phys. Plasmas 15, 023102 (2008)
** C. Chen, R. Pakter and R.C. Davidson, Phys. Rev. Lett. 79, 225 (1997)
BNL, Upton, Long Island, New York
In this article, based on the contributions of the chromatic sextupole families to the half-integer resonance driving terms, we discuss how to sort the chromatic sextupoles in the arcs of the Relativistic Heavy Ion Collider (RHIC) to easily and effectively correct the second order chromaticities. We propose an online method with 4 knobs or 4 pairs of chromatic sextupole families to correct second order chromaticities. Numerical simulations support this method and shows that it improves the balance of correction strengths among the sextupole families and avoids reversal of sextupole polarities, as well as yielding larger dynamic apertures for the 2009 RHIC 100 GeV polarized proton run.