JASRI/SPring-8, Hyogo-ken
KEK, Ibaraki
MHI, Tokyo
Mitsubishi Heavy Industries Ltd. (MHI), Takasago
We have been developing a system to generate a short pulse X-ray using crab cavities at SPring-8 Storage Ring. The ring holds 30-m long straight sections and the vertical beam size at the center of the straight sections is 6.5 micrometers in standard deviation. If we install four superconducting crab cavities and a mini-pole undulator in one of the straight sections, we can convert the time distribution of the electron bunch into the spatial distribution. After slicing the emitted photons with vertical slits, we can obtain a sub-picosecond X-ray pulse. In this scheme, the maximum repetition rate of the short pulse X-ray is the same as the acceleration frequency of the ring (508MHz) and user experiments at other beam-lines are not disturbed by this short pulse generation. We are planning to install KEKB type crab cavities as vertical deflectors. Phase fluctuation among crab cavities must be reduced less than 14 mdeg in order to avoid residual deflection in the vertical direction. In this paper, we report an overview of the short pulse generation scheme and topics of hardware development for stabilization of the RF phase fluctuation.
Siemens Med, Erlangen
Siemens DK, Jyllinge
FRIB, East Lansing, Michigan
Siemens has earned three contracts to deliver IONTRIS Particle Therapy accelerator systems* to be operated in Marburg and Kiel, both in Germany, and in Shanghai, China. The accelerator part consists of an injector (7 MeV/u protons and light ions) and a compact synchrotron able to accelerate proton beams up to 250 MeV and carbon ions up to 430 MeV/u. These beams can be slowly extracted and delivered to a choice of fixed-angle horizontal, semi-vertical and vertical beam-ports. An overview of the design will be given and the status of the installation and commissioning work for the first two projects will be shown.
*Particle Therapy is a work in progress and requires country-specific regulatory approval prior to clinical use.
NIRS, Chiba-shi
AEC, Chiba
Tumor therapy using energetic carbon ions, as provided by the HIMAC, has been performed since June 1994, and more than 5000 patients were treated until now. With the successful clinical results over more than ten years, we are constructing a new treatment facility. The new facility would have three treatment rooms; two of them have both horizontal and vertical fixed-irradiation-ports, and the other has a rotating-gantry-port. For all the ports, a scanning irradiation method is applied. The new facility is constructed in conjunction with the HIMAC, and heavy-ion beams will be provided by the HIMAC accelerators. To fulfill requirements for the scanning irradiation, we proposed multiple-energy operation with the quasi-DC extension of a flat top. With this operation, the beam energy can be successively varied within a single synchrotron-cycle, and therefore no energy degrader or the range shifter is required. The beam acceleration and extraction tests of the multiple-energy operation were successfully made. We will present the development of this operation as well as results of the beam acceleration tests.
SNU, Seoul
NCC, Korea, Kyonggi
Chung-Ang University, Seoul
Accelerator mass spectrometry (AMS) using a cyclotron has been studied because the system can be more compact and economical compared to the widespread commercial Tandem AMS. However, the previous efforts to build such a system showed that it has weakness in stability and transmission efficiency. To increase transmission efficiency it is important for the injection system to match not only the transverse phase space of a beam but also the longitudinal phase space with cyclotron acceptance. We plan to adopt a sawtooth RF buncher to increase transmission efficiency in the acceleration region of the cyclotron and a radial injection beam line. A goal in designing the injection line is to minimize the number of beam line elements to keep the system compact. The design of the injection system was carried out using the codes such as TRANSPORT and TRACE-3D. A prototype of the injection system is being constructed, and some results will be presented.
JAI, Oxford
Imperial College of Science and Technology, Department of Physics, London
UMAN, Manchester
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire
STFC/DL, Daresbury, Warrington, Cheshire
STFC/RAL, Chilton, Didcot, Oxon
Brunel University, Middlesex
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
GIROB, Oxford
Fermilab, Batavia
Gray Institute for Radiation Oncology and Biology, Oxford
Cockcroft Institute, Lancaster University, Lancaster
The status of PAMELA (Particle Accelerator for MEdicaL Applications) ' an accelerator for proton and light ion therapy using a non-scaling FFAG (ns-FFAG) accelerator ' is reviewed and discussed.
CERN, Geneva
Fermilab, Batavia
At each interconnection between LHC main magnets, a low-resistance solder joint must be made between superconducting cables to provide a continuous current path through the superconductor, and between the surrounding copper stabilizer to provide a current path in case the cable quenches. About 10,000 such joints exist in the LHC. An extensive campaign has been undertaken to characterize and map the resistances of both types of joints. All of the superconducting cable splices were measured using the enhanced protection system of the LHC superconducting circuits. No high-resistance superconductor splices were found above 3 nano-Ohms. Non-invasive measurements of the stabilizer joints were made at 300K in 5 of the 8 sectors, and at 80K in 3 sectors. More precise local measurements were made on suspect interconnects that were opened up, and poor joints were repaired. However, it is likely that additional imperfect stabilizer joints still exist in the LHC. A statistical analysis is used to place bounds on the remaining worst-case resistances. This sets limits on the maximum operating energy of the LHC, prior to a more extensive intervention.
CERN, Geneva
On 19th September 2008 the Large Hadron Collider (LHC) experienced a serious incident, caused by a bad electrical joint, which stopped beam operation just a few days after its beginning. During the following 14 months the damage was repaired, additional protection systems were installed and the measures to avoid a similar incident were taken (i.e. new layer of the Magnet Quench Protection System [nQPS], more efficient He release valves). As a consequence, a large number of powering tests had to be repeated or carried out for the first time. The re-commissioning of the already existing systems as well as the commissioning of the new ones has been carefully studied, then performed taking into account the history of each of the eight LHC sectors (warm-up, left at floating temperature,'). Moreover, a campaign of measurements of the bus-bar splice resistances has been carried out with the nQPS in order to spot out non conformities, thus assessing the risk of the LHC operation for the initial energy level. This paper discusses how the guidelines for the LHC 2009 re-commissioning were defined, providing a general principle to be used for the future re-commissioning.
W.C. Heraeus GmbH, Materials Technology Dept., Hanau
Plansee Metall GmbH, Reutte
TU Darmstadt, Darmstadt
DESY, Hamburg
The RRR value of high pure Nb is showing strong relations to the individual production steps. Mainly the different kind of internal stresses caused by the several production steps are resulting in the variation of the RRR value. This work shows the RRR values along the complete production chain from the molten Ingot till to the finished cavity. The influence of the RRR value caused by stresses and the release of that stresses by vacuum annealing is shown.
CERN, Geneva
EPFL, Lausanne
The control of the high intensity beams of the CERN Large Hadron Collider (LHC) is particular challenging and requires a precise knowledge of the critical beam and machine parameters. In recent years efforts were devoted to the design of a software infrastructure aimed at mimicking the behavior of the LHC. An online model of the machine, based on the accelerator design tool MADX, has been developed to support the commissioning and the operation of the LHC. This model is integrated into the JAVA-based LHC software framework and provides the full computing power of MADX, including the best knowledge of the machine aperture and magnetic models. The MADX implementation is server-based and provides various facilities for optics computation to other application clients. In this paper, we present the status of the MADX online application and illustrate how it has been used during the LHC commissioning. Possible future implementations are also discussed.
Kyushu University, Center for Accelerator and Beam Applied Science, Fukuoka
Kyushu University, Department of Applied Quantum Physics and Nuclear Engineering, Fukuoka
Kyushu University, Fukuoka
KURRI, Osaka
KEK, Ibaraki
SAGA, Tosu
150 MeV FFAG accelerator is under construction at Center for Accelerator and Beam Applied Science on Ito Campus to promote activities in all related scientific, medical, engineering and educational field at Kyushu University. In this paper, status of the development of hardware and the results of the beam commissioning of the injector are described.
JAI, Oxford
PAMELA (Particle Accelerator for MEdicaL Application) aims to design a particle therapy facility using Non-scaling FFAG (Fixed Field Alternating Gradient) accelerator. In the beam extraction in PAMELA, the biggest challenge is the flexible energy variability, which is desirable for better dose field formation. The feature is a unique feature of PAMELA for a fixed field accelerator. To realize energy variable beam extraction, PAMELA employs vertical extraction using large a aperture kicker magnet. In the paper, the detail of the extraction scheme, hardware specifications are discussed.
KEK, Ibaraki
The J-PARC accelerator complex consists of a linear accelerator (330 m long, 181 MeV), a rapid cycling synchrotron (3 GeV RCS, 350 m circumference, 25 Hz) and a slow cycling synchrotron (MR, 30 GeV as a first step energy, 1600 m circumference, typically with 3.5 sec cycle). The RCS provides high intensity proton beam to the materials and life science facility and the MR. The MR has two beam extraction lines. One is a slow extraction system for the hadron physics, and other a fast extraction system for neutrino science. We have to challenge many issues to complete construction of the J-PARC accelerator facility on-schedule in 2008 despite all the hardships, such as the problems included in the original design, technology choices and fabrication procedure of the machine components, and construction of conventional facilities. As a first step of operation, we could commission all accelerator facilities and provide beam to all experimental facilities in 2009 successfully. We will report about analysis of these issues and how to solve them, which is a necessary step to realize the design beam power as a next step, and to challenge the future upgrade beyond the original design.
JAEA/J-PARC, Tokai-mura
The J-PARC 3-GeV rapid cycling synchrotron (RCS) has been operated for the neutron and MLF users program from December 23rd, 2008. The RCS operations not only in support of the MLF but also were providing beam to support commissioning of the MR. In parallel we are challenging to realize higher beam power operations with better stability. Before scheduled maintenance last summer beam power was limited by the front end of about 20 kW, after that maintenance the RCS has been operated the beam power of more than 100 kW for MLF users. After beam deliver operation to the MR and MLF, while the priority has been given to their beam tuning, the RCS also continues further beam studies toward higher beam intensity. On December 7th, 2009, the RCS achieved the beam power of more than 300kW to the neutron production target with 25Hz. This presentation will concentrate itself on the outcome of the J-PARC RCS commissioning program, including the discussion on the issues of the high-power operation.
IHEP Beijing, Beijing
The accelerator of China Spallation Neutron Source (CSNS) consists of a low energy linac and a Rapid Cycling Synchrotron (RCS). The opimization of beam dynamics design for RCS and two beam transport line are introduced, and the details design and some simulation results are presented.
Kyoto ICR, Uji, Kyoto
We aim to develop a small and high intensity proton source for a compact accelerator based neutron source. Because this proton source shall be located close to RFQ for simplification, ratio of H+ to molecular ions such as H2+ or H3+ must be large. Therefore, we selected an ECR ion source with permanent magnets as small and high intensity ion source. ECR ion sources can provide high H+ ratio because of their high plasma temperature. Using permanent magnets makes the ion source small and running cost low. Because there is no hot cathode, longer MTBF is expected. Usually, gas is fed into ion sources continuously, even if ion sources run in pulse operation mode. But, continuous gas flow doesn't make vacuum in good level. So, we decided to install pulse gas valve directly to the plasma chamber. Feeding the gas only when the ion source is in operation reduces the gas load to the evacuation system and the vacuum level can be kept high. Up to now, we developed the first and second model of the ion source. And the research is being conducted using the second model. Recent experimental results will be presented.
GSI, Darmstadt
The engineering design, including the specifications for the accelerator components of the FAIR synchrotron SIS100 has been summarized in the Technical Design Report. The final stage of technical planning shall approach production readiness for the major technical systems in 2010. Significant progress has been achieved in the design of the cryomagnetic system with its main dipole and quadrupole modules, enabling the production of the first pre-series dipole magnet. Slight modifications of the lattice have been implemented to equalize most of the cryostat interconnections, leading to a simplified design and installation effort, and a reduced variety of components and spar parts. The new parallel tunnel allows optimal short interconnections between the supply units and power converters and the accelerator components. The status of the engineering design of SIS100 will be reported.
HIT, Heidelberg
While ramping the magnets in a synchrotron the magnetic fields deviate from their set values. Especially the field errors in dipole and quadrupole magnets result in different problems during operation. At the Heidelberg Ion Therapy Center HIT a measuring system with extremely high precision has been developed. It can measure in real time integral magnetic fields with a precision of better than 5*10-5 in a reproducible way. A feed-back control system for the magnetic fields is being installed and will be operational in May 2010. This control loop lets the magnets reach the nominal field much faster and thus shortens the dead time in a synchrotron cycle. The cycle can be reduced by 30% and more patients can be treated.
KAERI, Daejon
BNL, Upton, Long Island, New York
As a feasible extension plan of the proton engineering frontier project (PEFP) 100-MeV proton linac, the conceptual design of an rapid cycling synchrotron (RCS) is under progress. The main purpose of the synchrotron is a spallation neutron source and it also includes the slow extraction option for basic and applied science research. In the initial stage, the beam power is 60 kW by using a scheme of 100-MeV injection and 1-GeV extraction. There is a scheme to increase power to 500 kW through a 3-stage upgrade. The injection and extraction energies will be 200-MeV and 2-GeV respectively after the final upgrade. This article summarizes the present status of the RCS design. It includes the physics design including injection and acceleration, and conceptual design of some magnets and RF cavity.
CERN, Geneva
Fermilab, Batavia
Two events, occurring in 2008 during commissioning of the LHC circuits, lead to fundamental changes to the scope of circuit protection. The discovery of aperture-symmetric quenches and the accidental rupture at 9kA of an interconnecting busbar resulted in an emergency program for development and implementation of new protection facilities. The new scheme comprises a distributed busbar supervision system with early warning capabilities based on high-precision splice resistance measurements and system interlocks for rapid de-excitation of the circuit in case of a sudden splice resistance increase. The developed symmetric quench detectors are digital systems with radiation-resistant FPGA logic controllers, having magnet heater firing capabilities. This program successfully allowed a safe re-powering of the collider. The concept of the new electronics boards and the powering modules will be described. More than 14'600 extra cables and 6'000 new detector and control cards were added to the existing QPS system. A first evaluation of the system performance as well as a number of interesting discoveries made during the commissioning will be presented.
CERN, Geneva
Since the CERN PS Booster cannot simultaneously provide the beam brightness and intensity required, the nominal (25ns bunch spacing) proton beam for the LHC involves double-batch filling of the PS machine. Linac 4, which is under construction, will eventually remove this restriction. In the meantime, the request for 50 and 75ns bunch spacings to mitigate electron cloud effects has lowered the intensity demand such that the Booster can meet this in a single batch without compromising beam brightness. Single-batch transfer means providing two bunches from each of three Booster rings and, in turn, that the bunch spacing is modified by the addition of an h=1 rf component to the h=2 in the Booster in order to fit the h=7 rf buckets waiting in the PS (whilst leaving one bucket empty for kicker purposes). Following the first experiments performed in 2008, the rf manipulations in the Booster have been refined and those in the PS have been modified to cope with single-batch beams. This latest work is presented for both the 50 and 75ns variants.
SLAC, Menlo Park, California
CERN, Geneva
In order for the LHC to reach an ultimate luminosity goal of 1035, CERN is considering upgrade options for the LHC injector chain, including a new 50 GeV synchrotron of about 1.3 km length for protons and heavy ions, to be called the PS2. In this ring the proton energy is ramped from 4 GeV in 1.2 s, and the design (proton) current is 2.7 A. The present baseline of the vacuum system considers elliptical stainless steel chambers bakeable up to 300°C, various coatings to mitigate electron cloud are under study. For a bare stainless steel or Inconel chamber, the resistive wall wake alone will lead to multi-bunch instability, whereas for transverse mode coupling (TMCI), the threshold is above the design beam current, though this instability may become an issue once other impedance contributions are taken into account. A copper layer of varying thickness is shown to raise the TMCI threshold but to have relatively little effect on the multi-bunch resistive-wall growth rate unless the coating is very thick. We are also studying the effect of the copper coating on the penetration of the guide field during the energy ramp, which sets an upper limit on the allowable thickness.
JINR, Dubna, Moscow Region
Cockcroft Institute, Warrington, Cheshire
The Ultra-Low energy Storage Ring (USR) within the future Facility for Low-energy Antiproton and Ion Research (FLAIR) will decelerate antiproton beams from 300 keV to energies of only 20 keV. Cooled beams will then be extracted and provided to external experiments. The large variety of planned experiments requires a highly flexible longitudinal time structure of the extracted bunches, ranging from ultra-short pulses in the nanosecond regime to quasi DC beams. This requires fast as well as slow extraction in order to cover whole range of envisaged beam parameters. A particular challenge was to combine elements for fast and slow extraction in one straight section of this electrostatic ring. In this contribution we present the results of beam dynamic simulations and describe the overall extraction scheme in detail.
STFC/RAL/ISIS, Chilton, Didcot, Oxon
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
Imperial College of Science and Technology, Department of Physics, London
The front end test stand (FETS) [1] is entering the next stage of construction and commissioning, with the three-solenoid magnetic low energy beam transport (LEBT) line being installed. A thorough characterization of the beam leaving the Penning H- ion source has been performed. This includes measurements of the beam current using toroids and of the transverse emittance using slit-slit scanners. These measurements are performed over a wide range of source discharge and extraction parameters in order to understand how the transmission may be improved. Comments on the quality of the beam to be injected into the FETS radio frequency quadrupole (RFQ) are given.
ORNL, Oak Ridge, Tennessee
The chopper system for the Spallation Neutron Source (SNS) provides a gap in the beam for clean extraction from the accumulator ring. It consists of a pre-chopper in the low energy beam transport and a faster chopper in the medium energy beam transport (MEBT). It took several iterations to develop a working design with the required parameters. In this paper we describe the latest design of the MEBT chopper deflector and give results of the experimental verification of the chopper effectiveness, the gap cleanness and the rise time measured with high resolution using the SNS laser wire. The effect on the losses will be discussed as well.
HIP, University of Helsinki
Comenius University in Bratislava, Faculty of Mathematics Physics and Informatics, Bratislava
Helsinki University, Department of Physics, University of Helsinki
The Super-FRS is a superconducting fragment separator that will be built as part of the FAIR facility. For the slow-extraction part of the beam diagnostics system a total of 32 detectors are needed for beam monitoring and for tracking and characterization of the produced ions. Since GEM-TPC detectors can perform over wide dynamic range without disturbing the beam, they are suitable for this kind of in-beam detection. We have studied the performance of a prototype GEM-TPC. The current status of the prototype detector and the measurement results are shown.
KEK, Ibaraki
MELCO SC, Tsukuba
J-PARC, KEK & JAEA, Ibaraki-ken
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken
Experiences of operating BPM's during beam commissioning at the J-PARC MR are reported. The subjects are: (1) bug report, statistics and especially the effect of a beam duct step, (2) position resolution estimation (<30 micrometers with 1 sec averaging), (3) beam based alignment.
Kyungpook National University, Daegu
Royal Holloway, University of London, Surrey
KEK, Ibaraki
SLAC, Menlo Park, California
Nanometer resolution Beam Position Monitors have been developed to measure and control beam position stability at the interaction point region of ATF2. The position of the beam focused has to be measured within a few nanometer resolution at the interaction point. In order to achieve this performance, electronics for this BPM was developed. Every component of the electronics have been simulated and checked by local test and using beam signal. We will explain each component and define their working range. Then, we will show the performance of the electronics measured with beam signal.
IFIC, Valencia
A set of 16 Inductive Pick-Ups (IPU) for Beam Position Monitoring (BPM) with its associated electronics were designed, constructed and characterized at IFIC for the Test Beam Line (TBL) of the 3rd CLIC Test Facility (CTF3) at CERN. In October 2009 the full set of IPUs, (BPS) was successfully installed in the TBL line. In this paper, we describe the prototyping and series production phases of the BPSs development, focusing in the implementation and the results analysis derived from their characterization tests. Two special test benches were designed and built to perform the characterization tests at low and high frequencies. The low frequency set up based on a wire-method test bench for emulating the beam position variations helped us to determine the BPS performance parameters at beam pulse time scale from 100μs/10kHz to 10ns/100MHz. On the other hand, the high frequency test setup, based on an adapted coaxial transmission line, was dedicated to obtain the BPS longitudinal coupling impedance at the beam microbunches time scale (83ps/12GHz). Furthermore, we also present the first beam performance tests made in the TBL line.
CERN, Geneva
Gas Electron Multipliers (GEM) find their way to more and more applications in beam instrumentation. Gas Electron Multiplication uses a very similar physical phenomenon to that of Multi Wire Proportional Chambers (MWPC) but for small profile monitors they are much more cost efficient both to produce and to maintain. This paper presents the new GEM profile monitors intended to replace the MWPCs currently used at CERN's low energy Antiproton Decelerator (AD). It will be shown how GEMs overcome the documented problems of profile measurements with MWPCs for low energy beams, where the interaction of the beam with the detector has a large influence on the measured profile. Results will be presented from profile measurements performed at 5 MeV using four different GEM prototypes, with discussion on the possible use of GEMs at even lower energies needed at the AD in 2012.
JAI, Oxford
We present the design of a stripline beam position monitor (BPM) signal processor with low latency (c. 10ns) and micron-level spatial resolution in single-pass mode. Such a BPM processor has applications in single-pass beamlines such as those at linear colliders and FELs. The processor was deployed and tested at the Accelerator Test Facility (ATF2) extraction line at KEK, Japan. We report the beam test results and processor performance, including response, linearity, spatial resolution and latency.
JAI, Oxford
CERN, Geneva
Pepper-pot based transverse emittance measurement has the advantage of providing a fast (single shot) measurement with a relatively simple hardware. We report on Pepper-pot based transverse emittance measurements made at the CERN Linac 4 test stand.
J-PARC, KEK & JAEA, Ibaraki-ken
The J-PARC accelerator facility consists of a 400 MeV H- linac, a 3-GeV RCS, a 50-GeV MR (Main Ring) and related experimental facilities. Beam commissioning of the facility is started from the upstream accelerators while construction of the downstream accelerators and experimental facilities is in progress. The beam commissioning of MR, MLF(Materials and Life science experimental Facility) and Hadron experimental facility started in JFY 2008. In this presentation, we present an overview of the J-PARC commissioning status. Recent progress of MR commissioning will be described in more detail. The talk will focus on the issues, challenges, solutions, and lessons learned during the commissioning and early operations of J-PARC.
PSI, Villigen
CIAE, Beijing
With an average beam power of 1.3MW the PSI proton accelerator facility is presently at the worldwide forefront of high intensity accelerators. This talk describes critical aspects and recent improvements related to generation and transport of the high intensity beam in a cyclotron based facility. The installation of new accelerating resonators in the second of two cyclotrons led to a significant improvement in view of beam intensity but also the reliability of the facility. Besides the overall performance and further upgrade plans the discussed topics include: space charge dominated beam dynamics, beam loss handling, activation and specialized technical interlock systems.
KEK, Ibaraki
Hitachi Haramachi Electronics Co. Ltd., Hitachishi, Ibaraki
KFG, NEUSS
Kikusui Chemical Industries Co. Ltd, Kagamihara Shiga
KYOCERA Corporation, Higashiomi-city, Shiga
Pulsed Power Japan Laboratory Ltd., Kusatsu-shi Shiga
New beam abort system designed for KEKB upgrade, consists of horizontal and vertical kicker magnets, pulsed quadrupole magnets, a Lambertoson septum magnet and a beam dump. Water-cooling ceramic chambers are used for the kicker and pulsed quadrupole magnets. At the KEKB upgrade project, the beam abort gap is required to be less than 200 nsec. The beam currents are increased and their emittance is supposed to be much smaller than KEKB. In order to avoid melting the extraction Ti window, the pulsed quadrupole magnets will be installed. They enlarge the beam cross section at the extract window. The components for the SuperKEKB abort system are developed. The compact water-cooling ceramic chambers are developed to reduce the gap of kicker magnets and bore radius of the pulsed quadrupole magnets. The power supply for the kicker magnet is also developed to satisfy the 200 nsec rise time requirement.
JAEA/J-PARC, Tokai-mura
KEK/JAEA, Ibaraki-Ken
J-PARC, KEK & JAEA, Ibaraki-ken
KEK, Ibaraki
Applying narrow band longitudinal noise to the beam in J-PARC Main Ring in flattop, while the acceleration voltage is off might help to counteract the effect of ripple on the slow extraction. For this purpose, a complex noise sequence output by DSP modulates a custom made DDS synthesizer to create single side spectra without carrier. The noise is calculated starting from a description in frequency domain. Then an algorithm creates narrow band spectra with optimized behavior in time domain. Frequency domain data is transformed to time domain, and the amplitude is smoothed. The smoothed data is transformed back to frequency domain, and the spectral shape is restored. This process repeats until the amplitude in time domain has converged, while the desired spectrum shape is preserved. Noise generated in this way can be tailored for different requirements. We show the signal properties, the hardware, and preliminary beam test results, when the noise is applied to the MR RF system.
CERN, Geneva
In 2008 a project was started to renovate the CERN's PS Booster (PSB) low-level RF (LLRF). Its aim is to equip all four PSB rings with modern LLRF systems by 2013 at the latest. Required capabilities for the new LLRF include frequency program, beam phase, radial and synchronization loops. The new LLRF will control the signals feeding the three RF cavities present in each ring; it will also shape the beam in a dual harmonic mode, operate a bunch splitting and create a longitudinal blow-up. The main benefits of this new LLRF are its full remote and cycle-to-cycle controllability, built-in observation capability and flexibility. The overall aim is to improve the robustness, maintainability and reliability of the PSB operation and to make it compatible with the injection from the future LINAC4. The chosen technology is an evolution of that successfully deployed in CERN's ion accumulator ring LEIR and it is based upon modular VME 64X hardware and extensive digital signal processing. This paper outlines the main characteristics of the software and hardware building blocks. Promising initial beam tests are shown and hints are included on the main milestones and future work.
CERN, Geneva
The Low Energy Ion Ring (LEIR) is an accumulation ring in the Large Hadron Collider ion injector chain. After its successful start in 2005, it has been running in three operational campaigns. The LEIR LLRF system is the first all-digital low-level RF (LLRF) system to be made operational in a CERN circular machine. Composed of modular VME 64X hardware, it carries out extensive digital signal processing via Field Programmable Gate Arrays and Digital Signal Processors. System capabilities include beam control tasks, such as frequency program, beam phase, radial and synchronization loops, as well as cavity voltage/phase loops. All the system's control parameters are fully configurable, remotely and in-between cycles; extensive built-in diagnostics and signal observation features are available. The system has proven to be not only flexible and powerful but also extremely reliable. This is very important as the LEIR LLRF system is the pilot project for the LLRF renovation of other CERN's machines. This paper gives an overview of the main system building blocks and outlines their capabilities and operational features, along with results obtained during the first years of beam operation.
USTC/PMPI, Hefei, Anhui
USTC/NSRL, Hefei, Anhui
Microwave-absorbing material is an essential part of LINAC collinear load. It is coated on the inner walls of several trailing accelerating cavities to transform the remnant microwave power into heat. Fe-85%Si-9.6%Al-5.4% alloy, which reveals low outgassing rate and high attenuation, is selected for collinear load R&D. To measure the permittivity and permeability of FeSiAl at 2856 MHz, the coaxial transmission-reflection method is adopted. The system is firstly examined by testing the hollow coaxial fixture and comparing the results with the electromagnetic parameters of the air. Measurements of two PTFE rings show that the air gaps between the fixture and samples influence the test results seriously. CST is utilized to simulate the effects on the FeSiAl measure-ments. Eventually a scheme of molding the samples of FeSiAl powder mixed with paraffin to form a wax mold is proposed and the permittivity and permeability of FeSiAl are derived from the electromagnetic parameters equivalent formulas of mixed medium.
CERN, Geneva
DESY, Hamburg
The Super Proton Synchrotron (SPS) at CERN with a peak energy of 450GeV is at the top of the LHC preaccelerator-complex. Apart from the LHC, SPS is with Tevatron the accelerator with the largest stored beam energy of up to 2.5MJ. The SPS has a known vulnerability to fast equipment failures that led to an uncontrolled loss of a high intensity beam in 2008, which resulted in major damage of a main dipole. The beam loss was caused by a fast tune decrease towards an integer resonance. Simulations and distinct experimental studies provide clear understanding of the beam dynamics at different SPS tune resonances. Diverging closed orbit oscillations, dispersion explosion and increased beta-beating are the driving effects that lead to a complete beam loss in as little as 3 turns (70μs). Dedicated experiments of fast failures of the main power converters reveal that the current interlock systems are much too slow for an adequate machine protection. To counteract the vulnerability of the SPS, current research focuses on a new fast position interlock system which is planned to become operational in 2010.
BINP SB RAS, Novosibirsk
A new beam extraction scheme from a synchrotron is put forward. The main difference from other schemes of extraction is the use of a magnetic shields instead of a septum. Magnetic shields are located in the central dipole magnets of a pulsed chicane. The magnetic shield is a multi-layer copper-iron tube. Numerical simulations and experimental results for the magnetic shield are presented. A good accordance between them has shown. The advantages of the new scheme are easy technical implementation and compactness. The area of application is extraction from a synchrotron. The proposed scheme will be used in a new synchrotron radiation source in Novosibirsk.
CERN, Geneva
The LHC beam dump system was commissioned with beam in 2009. This paper describes the operational experience with the kicker systems and the tests and measurements to qualify them for operation. The kicker performance was characterized with beam by measurements of the kicker waveforms using bunches extracted at different times along the kicker sweep. The kicker performance was also continuously monitored for each pulse with measurement and analysis of each kick pulse, allowing diagnostic of errors and of long-term drifts. The results are described and compared to the expectations.
EBG MedAustron, Wr. Neustadt
CERN, Geneva
The LHC beam dump system has to safely dispose all beams in a wide energy range of 450 GeV to 7 TeV. A 3 μs abort gap in the beam structure for the switch-on of the extraction kicker field ideally allows a loss free extraction under normal operating conditions. However, a low number of asynchronous beam aborts is to be expected from reliability calculations and from the first year's operational experience with the beam dump kickers. For such cases, MAD-X simulations including all optics and alignment errors have been performed to determine loss patterns around the LHC as a function of the position of the main protection elements in interaction region six. Special attention was paid to the beam load on the tungsten collimators which protect the triplets in the LHC experimental insertions, and the tracking results compared with semi-analytical numerical estimates. The simulations are also compared to the results of beam commissioning of these protection devices.
CERN, Geneva
The movable LHC injection protection devices in the SPS to LHC transfer lines and downstream of the injection kicker in the LHC were commissioned with low-intensity beam. The different beam-based alignment measurements used to determine the beam centre and size are described, together with the results of measurements of the transverse beam distribution at large amplitude. The system was set up with beam to its nominal settings and the protection level against various failures was determined by measuring the transmission and transverse distribution into the LHC as a function of oscillation amplitude. Beam losses levels for regular operation were also extrapolated. The results are compared with the expected device settings and protection level, and the implications for LHC operation discussed.
CERN, Geneva
The commissioning of the beam transfer systems for LHC included detailed aperture measurements in the injection regions and for the beam dump systems. The measurements, mainly single pass, were made using systematic scans of different oscillation phases and amplitudes, and the results compared with the expectations from the physical aperture model of the LHC. In this paper the measurements and results are presented and compared with the specified apertures in these critical areas.
NSRRC, Hsinchu
National Tsing-Hua University, Hsinchu
The test results of a dual one-turn coils configuration for Taiwan Light Source (TLS) booster extraction kicker is presented in this report. The achieved capability of the test unit demonstrates that the rise-time of the kicker current pulse has been improved for beam extraction optimization. This improved performance is mainly accomplished by reducing the load inductance effectively with a dual one-turn coils configuration. The measured result of rise-time variation versus the corresponding load inductance change is briefly discussed.
BNL, Upton, Long Island, New York
Booster extraction presents a number of problems that include strengths and waveforms of the pulsed magnets and design of the vacuum chamber. Instabilities in the booster extraction may compromise the extracted beam quality deteriorating value of high-performance injector design. Here we discuss requirements and tolerances for the extraction system components and methods of increasing its performance.
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken
KEK, Ibaraki
The Longitudinal emittance in J-PARC RCS should be controlled to accelerate a high intensity proton beam with minimal beam loss. In order to study and minimize the beam loss during acceleration, the optimized way to add the 2nd higher harmonic rf has been calculated by a particle tracking code. Furthermore, the bunch shape at RCS extraction should be controlled and optimized for the MR injection. For this purpose, the optimum RCS acceleration pattern has been calculated. We describe the simulation results and the comparison with the beam test.
LBNL, Berkeley, California
CERN, Geneva
A replacement for the PS storage ring is being considered, in the context of the future LHC accelerator complex upgrade, that would likely place the new machine (the PS2) in a regime where the electron-cloud (EC) effect might be an operational limitation. We report here our present understanding of the ECE build-up based on simulations. We focus our attention on the bending magnets and the field-free regions, and consider both proposed bunch spacings of 25 and 50 ns. The primary model parameters exercised are the peak secondary emission yield (SEY) δmax, and the electron-wall impact energy at which SEY peaks, Emax. By choosing reasonable values for such quantities, and exploring variations around them, we estimate the range for the EC density ne to be expected in nominal operation. We present most of our results as a function of bunch intensity Nb, and we provide a tentative explanation for a curious non-monotonic behavior of ne as a function of Nb. We explore the sensitivity of ne to other variables such as the beam pipe radius in the field-free regions.
CERN, Geneva
Electron-cloud is one of the main limitations for particle accelerators with positively charged beams of high intensity and short bunch spacing, as SPS at CERN. The Secondary Electron Yield (SEY) of the inner surface of the vacuum chamber is the main parameter governing the phenomenon. The effect could be eliminated by coating the magnets vacuum chambers with a material of low SEY, which does not require bake-out and is robust against air exposure. For such a purpose amorphous carbon coatings were produced by magnetron sputtering of graphite targets. They exhibit maximum SEY between 0.9 and 1.1 after air transfer to the measuring instrument. After 1 month air exposure the SEY rises to values between 1.1 and 1.4. Storage under nitrogen or by packaging in Al foil makes this increase negligible. The coatings have a similar XPS C1s spectrum for a large set of deposition parameters and exhibit an enlarged line-width compared to pure graphite. The static outgassing without bake-out depends on deposition parameters and is in a range from 1 to 10 times higher than that of stainless steel. Instead, electron stimulated outgassing is lower than for stainless steel and is dominated by CO.
KEK, Ibaraki
The beam extraction experiment using the strip-line kicker has been carried out at KEK-ATF. The specification of the International linear collider (ILC) is that the long bunch train (1320 - 5120 bunches), which has the bunch spacing of 189 - 480ns, is compressed to 3 or 6ns bunch spacing into the DR, and again decompressed from the DR. The kicker manipulates the changes of the bunch spacing. The kicker requires a fast rise/fall time (3 or 6ns) and a high repetition rate (3 or 6MHz). A multiple strip-line kicker system is the most promising candidate to realize the specification for the ILC*. The beam extraction experiment at KEK-ATF** using proto-type of the strip-line kicker was done by following parameters, up to 30 bunches of the multi-bunch in the DR, which has 5.6ns bunch spacing, are extracted bunch-by-bunch with 308ns interval to the extraction line. The stored multi-bunch was extracted successfully. The detail of the experiment and the result are reported.
* T. Naito et. al., Proc. of PAC07, pp2772-2274.
** T. Naito et. al., Proc. of EPAC08, pp601-603.
KEK, Ibaraki
This presentation will cover the development of the tuning methods, beam stabilization and reliability, and instrumentation including laser wires, high resolution BPMs and fast feedback, to achieve the beam of a few nano meters size required for the ILC final focus.
Tohoku University, Graduate School of Science, Sendai
KEK, Ibaraki
Tohoku University, School of Scinece, Sendai
We have studied a beam orbit tilt monitor for stabilizing the beam orbit in ATF2. Once we can measure a beam orbit tilt with high precision at one point, we can relate this data with the beam position profile at the focal point. A tilt monitor is composed of a single rectangular sensor cavity and a waveguide to extract the signal. In the sensor cavity, there is the most basic resonant mode called monopole mode. This monopole mode is perpendicular to the nominal beam axis, and excited by the beam tilt. We extract this monopole mode. As the result, the amplitude of the extracted signal is proportional to the tilt angle. The tilt monitor is almost indepnedent with beam postion, so we can get the tilt date independently. According to our simulation, the sensitivity is estimated about 35nrad in the vertical direction. The prototype was completed and installed in the test area on the ATF2 beamline. The first beam test will be performed in December 2009. We will report this result and future update plan.
SESAME, Amman
The construction of SESAME, a 2.5 GeV, and 3rd generation synchrotron-light source is under progress. The first electron beam from the Microtron at low energy (less than 10 MeV) could be obtained on July, 14th, 2009 and reproduced several times. The tests of the injection and extraction system as well as the hydraulically and electrical tests of the main magnets of the Booster are complete and the vacuum chambers tests are underway. The Booster RF cavity and its plunger have been conditioned successfully by 1.7 kW CW RF power. The installation of the Booster is expected to start after the completion of the shielding. The design of the completely new storage ring is finalised and the Phase 1 beamlines is updated.
BNL, Upton, Long Island, New York
TRIUMF, Vancouver
The low beam emittance requirement in the NSLS-II storage ring imposes a very tight constraint on its acceptance. This requires the injected beam emittance to be very small, for which a reliable scheme of measurement to determine the phase space and momentum characteristics of the beam coming out the booster is necessary. The original scheme based on the booster-to-dump transport line was hampered by the difficulty in decoupling betatron oscillation from dispersion, due to high concentration of dipoles and limited number of quads after the booster. This paper will describe the alternative method being planned to use the booster extraction line to measure the beam emittance and energy spread, as well as the associated errors.
J-PARC, KEK & JAEA, Ibaraki-ken
JAEA/J-PARC, Tokai-mura
KEK, Ibaraki
In the J-PARC Main Ring (MR), the bending, quadrupole, sextupole, and steering magnets can be controlled on the operating interfaces (OPI). The optics parameters for all magnets are calculated by using SAD, and are converted to BL tables (ex: 2000 points for a steering magnet) for each power supplies. The BL tables are made from the parameters of optics, pattern timing, and beam energy at flat bottom and flat top. For MR beam studies, the BL tables are adjustable with offset and factor. This system is useful for COD correction, beta function measurement, aperture survey, and slow extraction. In this proceeding, the structure of the magnet control system and OPIs for beam studies will be shown.
JAEA/J-PARC, Tokai-mura
KEK, Ibaraki
MELCO SC, Tsukuba
J-PARC, KEK & JAEA, Ibaraki-ken
The Data Acquisition System of Beam Position Monitors(BPMs) in J-PARC Main Ring are consist of 186 Linux-based Data Processing Cirquits(BPMCs) and 12 EPICS IOCs. They are important tool to see the COD and turn-by-turn beam positions. This report describes the process of the data reconstruction which include how the various calibration constants are applied.
CERN, Geneva
To cope with the large variety of different beams for the LHC, the RF beam control in the CERN PS has evolved continuously to improve its flexibility and reliability. Single-bunch beams, several different multi-bunch beams with 25, 50 or 75 ns bunch spacing at ejection for LHC filling, as well as two lead-ion beam variants are now regularly produced in pulse-to-pulse operation. The multi-bunch beam control for protons can be easily re-adjusted from 0.25·1011 to 1.3·1011 particles per ejected bunch. Depending on the number of bunches injected from the PS Booster, the length of the ejected bunch train may vary from 8 to 72 bunches. This paper summarizes recent improvements in the low-level RF systems and gives an outlook on the future consolidation.
KEK, Ibaraki
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken
Transverse bunch by bunch feedback systems for J-PARC MR accelerator has been designed and tested. Bunch positions are detected by Log-ratio position detection systems with center frequency of 12 MHz. The digital filter which consists of two LLRF4 boards samples the position signal with 64 times of RF frequency. Up to four sets of 16 tap FIR filter with one-turn delay and digital shift gain can be used. Preliminary results of beam test of the system are also shown.
Tokyo City University, Tokyo
KEK, Ibaraki
Miyazaki University, Miyazaki
NIRS, Chiba-shi
Tsukuba University, Ibaraki
J-PARC is a new accelerator facility to produce MW-class high power proton beams. From the main ring (MR) high energy protons are extracted in a slow extracted mode for hadron experiments. The beam is required with as small ripple as possible to prevent pileup events in particle detectors or data acquisition systems. We took beam tests at HIMAC using a prototype signal processing unit. In these beam tests we had recognized the improvement of the extracted beam structure by using the feedback algorithm whose parameters were changed according to the beam characteristics. We have developed a new signal processing unit for the spill feedback control of J-PARC. The unit consists of three signal input ports (gate, spill intensity and residual beam intensity), three signal output ports (spill control magnets), two DSPs (power spectrum analysis and spill feedback control), dual port memories, FPGAs and a LAN interface (remote control with SUZAKU-EPICS). From October 2009, this unit is being used in the beam study of J-PARC MR to check the performance of digital filtering, phase-shift processing, servo feedback control, real-time power spectrum analysis and adoptive control.
JAI, Oxford
IFIC, Valencia
The commissioning of the ATF2 final focus test beam line facility is currently progressing towards the achievement of its first goal: to demonstrate a transverse beam size of about 40 nm at the focal point. In parallel, studies and R&D activities have already started towards the second goal of ATF2, which is the demonstration of nanometer level beam orbit stabilization. These two goals are important to achieve the luminosity required at future linear colliders. Beam-based intra-train feedback systems will play a crucial role in the stabilization of multi-bunch trains at such facilities. In this paper we present the design and simulation results of beam-based intra-train feedback systems at the ATF2: one system located in the extraction line at the entrance to the final focus, and another at the interaction point. The requirements and limitations of these systems are also discussed.
JAI, Oxford
We present the design and beam test results of a prototype beam-based digital feedback system for the Interaction Point of the International Linear Collider. A custom analogue front-end signal processor, FPGA-based digital signal processing boards, and kicker drive amplifier have been designed, built, deployed and tested with beam in the extraction line of the KEK Accelerator Test Facility (ATF2). The system was used to provide orbit correction to the train of bunches extracted from the ATF damping ring. The latency was measured to be approximately 140 ns.
CERN, Geneva
A complex Machine Protection System has been designed to protect the LHC machine from an accidental release of the beam energy, with about 20 subsystems providing status information to the Beam Interlock System (BIS). Only if the subsystems are in the correct state for beam operation, the BIS receives a status flag and beam can be injected into LHC. The BIS also relays commands from the connected subsystems in case of failure for emergency extraction of beam to the LHC Beam Dump Block. To maintain the required level of safety of the BIS, the performance of the key components is verified before every fill of the machine and validated after every emergency beam dump before beam operation is allowed to continue. This includes all critical paths, starting from the inputs from connected system triggering a beam dump request, followed by the correct interruption and propagation sequence of the two redundant beam permit loops until the final extraction of the beam via the LHC beam dumping system. In this paper we report about the experience with the BIS that has been deployed for some years in the SPS (as LHC injector), in the transfer lines between SPS and LHC and recently in LHC.
OXFORDphysics, Oxford, Oxon
JAI, Oxford
We present the results of the development of a high power fibre laser system for the laserwire project to measure very low emittance electron beams. We use the output of a commercial 1uJ, 6.49MHz laser system and amplify it in rod type photonic crystal fibre. This is a novel form of optical fibre which has a large core diameter (70um) but still supports only a single Gaussian spatial mode, essential for focusing the beam to the smallest spot size and achieving the highest resolution. We amplify the seed pulses in a burst mode suitable for use in a linear accelerator, which has the advantage of decreasing the pump power required and thus reducing the running cost and heat loading of the laser system. The amplified pulses have energies of ~ 100uJ in the near infrared and excellent beam quality, as specified in the original design, and are frequency converted to the green to give sub-micron spatial resolution.
CERN, Geneva
The Compact Linear Collider (CLIC) study is exploring the scheme for an electron-positron collider with high luminosity (1034 - 1035 cm2/s) and a nominal centre-of-mass energy of 3 TeV: CLIC would complement LHC physics in the multi-TeV range. The CLIC design relies on the presence of Pre-Damping Rings (PDR) and Damping Rings (DR) to achieve the very low emittance, through synchrotron radiation, needed for the luminosity requirements of CLIC. In order to limit the beam emittance blow-up due to oscillations the combined flat-top ripple and droop of the field pulse, for the DR extraction kickers, must be less than 0.015%. In addition, the allowed beam coupling impedance for the kicker systems is also very low: a few Ohms longitudinally and a few MΩ/m transversally. This paper discusses initial ideas for achieving the extremely demanding requirements for the PDR and DR kickers.
CERN, Geneva
A five-turn continuous extraction is currently used to transfer the proton beam from the CERN PS to the SPS. This extraction uses an electrostatic septum to cut the filament beam into five slices, causing losses of about 15 %. These losses would be an even greater drawback when the beam intensity is further increased for the CERN Neutrinos to Gran Sasso facility. To overcome this, a Multi-Turn Extraction (MTE) has been implemented, in which the beam is separated, prior to extraction, into a central beam core and four islands. Each beamlet is extracted using a set of kickers and a magnetic septum. For the kickers two new pulse generators have been built, each containing a lumped element Pulse Forming Network (PFN) of 12.5 Ohms, 80 kV and 10.5 μs. For cost reasons existing 15 Ω transmission line kicker magnets are reused. The PFN characteristic impedance deliberately mismatches that of the magnets to allow a higher maximum kick. The PFN design has been optimised such that undesirable side-effects of the impedance mismatch on kick rise-time and flat-top remain within acceptable limits. The kicker systems put in place for the current first phase of MTE are presented.
NSRRC, Hsinchu
National Tsing-Hua University, Hsinchu
A test unit of a pulse-forming-network (PFN) kicker power supply has been designed and fabricated for Taiwan Photon Source (TPS) beam injection/extraction of the booster ring. In order to fulfill the requirements, the performance of the designed unit has been bench tested and the results are examined for evaluation purpose. The pulse-to-pulse stability and the flattop specifications are specified according to the beam injection/extraction requirements. Effort has been made to enhance the rise/fall time of the delivered pulse current. The engineering evaluation and its possible application for beam diagnostics purpose are briefly discussed.
CERN, Geneva
One crucial development for CLIC is an adjustable high-power rf device which controls the output power level of individual Power Extraction and Transfer Structures (PETS) even while fed with a constant drive beam current. The CLIC two-beam rf system is designed to have a low, approximately 10-7, breakdown rate during normal operation and breakdowns will occur in both accelerating structures and the PETS themselves. In order to recover from the breakdowns and reestablish stable operation, it is necessary to have the capability to switch off a single PETS/accelerating structure unit and then gradually ramp generated power up again. The baseline strategy and implementation of such a variable high-power mechanism is described.
ANL, Argonne
Euclid TechLabs, LLC, Solon, Ohio
In this paper, we present a linear collider concept based on drive beam generation from an RF photoinjector, and employing dielectric structures for power extraction and acceleration. The collider is based on a modular design with each module providing 100 GeV net acceleration. A high current drive beam is produced using a low frequency RF gun (~ 1GHz), and subsequently accelerated to ~1 GeV using conventional standing wave cavities. High frequency (20 GHz) RF power, extracted from the drive beam using a low impedance dielectric structure, is used to power the main linacs, which are based on high impedance high gradient dielectric loaded accelerating structures. We envision this scheme will produce high gradients (300 MeV/m), leading to a very compact design. The modularity of the design will allow a staged construction that will enable extension to multi-TeV energies.
Imperial College of Science and Technology, Department of Physics, London
UMAN, Manchester
Cockcroft Institute, Warrington, Cheshire
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
Osaka University, Osaka
Fermilab, Batavia
KURRI, Osaka
UCL, London
FZJ, Jülich
KEK/JAEA, Ibaraki-Ken
STFC/RAL, Chilton, Didcot, Oxon
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire
JAI, Oxford
The next generation of lepton flavour violation experiments will use high intensity and high quality muon beams. Such beams can be produced by sending a short proton pulse to the pion production target, capturing pions and performing RF phase rotation on the resulting muon beam in an FFAG ring, which was proposed for the PRISM project. A PRISM task force was created to address the accelerator and detector issues that need to be solved in order to realise the PRISM experiment. The parameters of the initial proton beam required and the PRISM experiment are reviewed. Alternative designs of the PRISM FFAG ring are presented and compared with the reference design. The ring injection/extraction system, matching with the solenoid channel and progress on the ring's main hardware systems like RF and kicker magnet are discussed. The activity on the simulation of a high sensitivity experiment and the impact on physics reach is described. The progress and future directions of the study are presented in this paper.
Imperial College of Science and Technology, Department of Physics, London
BNL, Upton, Long Island, New York
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
STFC/RAL, Chilton, Didcot, Oxon
JAI, Oxford
Nonscaling FFAG is required for the muon acceleration in the Neutrino Factory, which baseline design is under investigation in the International Design Study (IDS-NF). In order to inject/extract the muon beam with a very large emittance, several strong kickers with a very large aperture are required distributed in many lattice cells. Once the sufficient orbit separation is obtained by the kickers, the final degree of separation from the lattice is made by the septum, which needs to be superconducting. The geometry of the symmetric solutions allowing to inject/extract both signs of muons is presented. The preliminary design of the kicker and septum magnets is given.
Cockcroft Institute, Warrington, Cheshire
A new lattice design for the ILC damping ring has been developed since the beginning of 2008 as a lower cost alternative to the previous OCS6 design. The lattices for the electron and positron damping rings are identical, and are designed to provide an intense, 5 GeV beam with low emittance at extraction. The latest design, presented in this paper, provides sufficient dynamic aperture for the large positron beam at injection. The lattice also meets the engineering requirements for arrangement of the positron ring directly above the electron ring in the same tunnel, using common girders for the magnets in the two rings, but with the beams circulating in opposite directions.
IMP, Lanzhou
CSR has recently made significant progress in commissioning a variety of light to heavy ion in the cooler ring. Also, carbon therapy was successfully carried out. A significant achievement is the energy modulation extraction using slow extraction realizing 3D conformal treatment.
CERN, Geneva
ESRF, Grenoble
Following the analysis of the results obtained during the first year of beam commissioning of the CERN multi-turn extraction, a number of changes have been introduced in the beam manipulations performed in the CERN Proton Synchrotron. This includes a different control of the linear chromaticity, the setting of the non-linear magnets used to split the beam, and the longitudinal structure in the PS. The results obtained during the 2009 run are presented and discussed in detail, including the beam performance in both the PS and the SPS, as well as the optics measurements in the transfer line between the two circular machines.
HU/AdSM, Higashi-Hiroshima
Hiroshima University, Faculty of Science, Higashi-Hirosima
An ion plasma confined in a compact trap system is Coulomb crystallized near the absolute zero temperature. The emittance of the crystallized ion plasma is close to the ultimate limit, far below those of any regular ion beams. This implies that, if we can somehow accelerate a crystal without serious heating, an ion beam of extremely low emittance becomes available*. Such ultra-low emittance beams, even if the current is low, can be used for diverse purposes including precise single ion implantation to various materials and for systematic studies of radiation damage effects on semiconductors and bio-molecules. We performed proof-of-principle experiments on the extraction of Coulomb crystals from a linear Paul trap system developed at Hiroshima University. A string crystal of 40Ca+ ions is produced with the Doppler laser cooling technique and then extracted by switching DC potentials on the trap electrodes. We demonstrate that it is possible to transport the ultra-low temperature ion chain keeping its ordered configuration.
* M. Kano et al., J. Phys. Soc. Jpn. 73, No.3, 760 (2004).
CIEMAT, Madrid
CERN, Geneva
The goal of the present CLIC test facility (CTF3) is to demonstrate the technical feasibility of the CLIC scheme. The Test Beam Line (TBL) is used to study a CLIC decelerator focusing on 12 GHz power production and the stability of the decelerated beam. The extracted CTF3 drive beam from the combiner ring (CR) features a maximum intensity of 28 A and 140 ns pulse duration, where the Test Beam Line consists of 16 cells, each one including a BPM, a quadrupole on top of a micrometer-accuracy mover and a RF power extractor so-called PETS (Power Extraction and Transfer Structure). This paper describes the first prototype fabrication techniques, with particular attention to the production of the long copper rods which induce the RF generation. A special test bench for the characterization of the device with low RF power measurements has been developed. Performed mesurements of the scattering parameters and the electric field profile along the structure are carefully described. Finally, the prototype has been installed at CLEX, and first measurements with beam are also reported.
KEK, Ibaraki
In J-PARC 50GeV synchrotron ring, large vacuum pressure rises above 10-3 Pa are found at 30GeV acceleration final stage of intensity over 1013 protons per pulse in the chambers of the in-vacuum electrostatic septum magnet for the slow-extraction(SX), magnetic septum for SX, and the kicker magnet for the fast-extraction. This pressure rise depends on beam intensity and peak-current, and can be reduced by continuous beam operations, such as scrubbing with proton beam, secondary emission electrons and other cations of remaining gasses or desorptions.
GSI, Darmstadt
ITEP, Moscow
The heavy ion synchrotron SIS-100 will play a key role within the future FAIR project underway at GSI. Although this synchrotron is optimized for fast extraction, also slow extraction will be used. Slow extraction is based on beam excitation due to a third order resonance. The spread in the particle momenta generating a tune spread causes particle loss leading to an irradiation of the machine especially in a high-current operation. A major part of the losses is assumed to occur at the electro-static separator. In the present study we apply a tracking method to model the extraction process to predict the losses, where, in a first step, high current effects are not taken into account.
GSI, Darmstadt
IAP, Frankfurt am Main
With the ability to accelerate heavy ions up to an energy of 32 GeV/u, the SIS300 superconducting (sc) synchrotron is a central part of the new FAIR facility at GSI-Darmstadt. SIS300 will provide beams with a 20-fold increase in energy and, by means of a stretcher mode or a fast ramped mode (1 T/s), 100-10000 times higher average intensity. The beam from SIS300 will be extracted towards the experiments using resonant slow extraction, thus SIS300 becomes the first superconducting synchrotron worldwide with this feature. Coupling and persistent currents are the main practical limitation for operation of sc magnets at high ramping rates and long slow extraction plateaus. The effect of the persistent currents, which are time dependent and depend as well on the magnet's history, is especially critical for slow extraction at low energies. These effects determine the tolerances on magnetic components. In order to address this issue, detailed simulations of beam dynamics at slow extraction have been performed. In particular, the optimization of the lattice and its optical parameters for a low-loss extraction in the presence of steady and time-dependent field components will be presented.
National Technical University of Athens, Zografou
CERN, Geneva
Dispersion and beam optics measurements were carried out in the transfer line between the CERN PS and SPS for the new Multi-Turn Extraction beam. Since the extraction conditions of the four islands and the core are different and strongly dependent on the non-linear effects used to split the beam in the transverse plane, a special care was taken during the measurement campaigns. Furthermore, an appropriate strategy was devised to minimize the overall optical mismatch at SPS injection. All this led to a new optical configuration that will be presented in detail in the paper.
INFN/LNF, Frascati (Roma)
CNAO Foundation, Milan
CERN, Geneva
University of Pavia, Pavia
The National Centre for Oncological Hadrontherapy (CNAO) is the first Italian centre for the treatment of patients affected by tumours with proton and carbon ions beams. Its status and commissioning results are presented in this conference in several papers. The synchrotron beam extraction is based on the use of a betatron core. The possibility of using the RF-knockout method as alternative system is being investigated, trying to optimise the performances with the already present hardware and minimum upgrades. A multiparticle tracking program has been written to simulate the beam dynamics during the extraction of the synchrotron, and to optimise the parameters of the radio frequency system. Two types of signals have been studied in order to obtain a constant spill with the minimum ripple: a carrier wave with a frequency and amplitude modulation, and a noise at a given range of frequencies modulated in amplitude. The results of the optimisation and the parameters of the proposed system are presented.
NIRS, Chiba-shi
The betatron tune fluctuation due to the current ripple of power supplies brings the beam spill ripple through the stable area variation in resonant slow extraction. The effect becomes dominant especially in the case of the low beam rate extraction. The RF-knockout slow extraction method is insensitive to the tune ripple compared to the ordinary one because it uses the diffusion with the transverse RF field. However, the ripple effect appears even in the beam spill extracted by it. The amount of the separatrix fluctuation due to the tune ripple depends on the difference between the bare and the resonant tune, and the sextupole magnetic strength. We measured the correlation between the beam spill and the tune ripple which was the artificially generated with low and high frequency components of 67 Hz and 1167 Hz near those of the real current ripple. We confirmed the reduction of the beam spill ripple by setting the tune away from the resonance while keeping the separatrix area. The comparison between the experimental results, the analytical calculation and the simulation will be reported.
KEK, Ibaraki
University of Fukui, Faculty of Engineering, Fukui
Nippon Advanced Technology Co. Ltd., Ibaraki-prefecture
The two electrostatic septa are one of the most important device for the slow extraction in 50GeV proton synchrotron. We have developed the thin ribbon type septum in order to reduce the beam loss. If alignment of ribbons is poor, the effective thickness seen from the beam become large, and it would increase the beam-hitting rate. The alignment of ribbon over 1.5m long septa was measured by a laser-focus displacement meter. The achieved effective thickness of septa is estimated to be 0.075mm and 0.080mm respectively. We will report a high voltage conditioning and a performance under beam commissioning.
KEK, Ibaraki
J-PARC, KEK & JAEA, Ibaraki-ken
University of Fukui, Faculty of Engineering, Fukui
Tokyo City University, Tokyo
Tsukuba University, Ibaraki
JAEA/J-PARC, Tokai-mura
High power protons from the J-PARC main ring is slowly extracted using the third integer resonance and delivered to the experimental hall for various nuclear and particle physics experiments. The slow extraction device comprises two electro static septa (ESS),ten magnetic septa, four bump magnets, eight resonant sextupole magnets and their power supply. One of the critical issue of the slow extraction is radiation caused by the beam loss during the slow extraction. We have developed the electrostatic and magnetic septa with thin septum thickness. A unique scheme with large step size and small angular spread of the extracted beam enables hit rate on the ESS less than 1% level. In January 2009, first 30 GeV proton beam has been successfully delivered to the fixed target. Quadrupole magnets and a DSP feedback control system to obtain a uniform beam spill structure were implemented in 2009 summer shutdown period. We will report the extraction efficiency, extracted beam profiles and spill structure obtained by the beam commissioning so far. We will also mention a upgrade plan based on some new ideas to aim a higher performance.
KEK/JAEA, Ibaraki-Ken
J-PARC, KEK & JAEA, Ibaraki-ken
KEK, Ibaraki
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken
The beam commissioning of J-PARC/MR has been started from May 2008 and is in progress*. One key purpose of MR commissioning is the 30 GeV beam fast extraction to Neutrino beam line, which reflect the overall commissioning result. In the MR, the third straight section is assigned for the fast extraction. 5 kickers and 8 septa were installed there, which can give beam a bipolar kick to inside or outside of MR. Inside kick means beam to Neutrino Oscillation Experiment, while outside kick means beam dumped to abort line. However before commissioning, the measured magnetic field distribution of each septa shows non-linear profile along the horizontal direction. In order to find the influence, a simulation with these measured field has been performed. Depends on this study and some OPI (Operation Interface) made by code SAD for orbit modification online, fast extraction of 30 GeV beam to Neutrino line has been achieved on April 23rd 2009. Beam orbit have been tuned to less than 0.5 mm and 0.1 mrad in both horizontal and vertical at the beginning of Neutrino line, which is also the end of MR fast extraction. And so far, 100 kW continual operation to neutrino line have been achieved, too.
* T. Koseki, "Challenges and Solutions for J-PARC Commissioning and Early Operation", in these proceedings
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken
KEK/JAEA, Ibaraki-Ken
KEK, Ibaraki
The hybrid type thick boron-doped carbon (HBC) stripping foils are installed and used for the beam injection at the 3GeV RCS (Rapid Cycling Synchrotron) in J-PARC (Japan Proton Accelerator Research Complex). The HBC foils are developed by Sugai group in KEK, which improved the lifetime drastically. Up to now, the performance deterioration of the stripping foils can not be seen after the long beam irradiation for the 120kW user operation and 300kW high power beam demonstration at the RCS. In order to examine the characteristic of the HBC foils, various beam studies were carried out. The beam-irradiated spot at the foil was measured by scanning the foil setting position, the charge exchange efficiency was evaluated with various thickness foils, and the effect of the SiC fibers supporting the foil mounting was checked with different mounting foils. Beam study results obtained with using the HBC foils will be presented. In addition, the trends of outgas from the stripping foils and the deformations of the foils during the beam irradiation will be reported.
KEK, Tsukuba
Miyazaki University, Miyazaki
Tokyo City University, Tokyo
NIRS, Chiba-shi
The slow extraction beam from the J-PARC Main Ring (MR) to the Hadron Experimental Facility is used in various nuclear and particle physics experiments. A flat structure and low ripple noise are required for the spills of the slow extraction. The spill control system has been developed for the J-PARC slow extraction to make a flat structure and small ripple. It consists of the extraction quadrupole magnets and feedback device. The extraction magnets consist of two kinds of quadrupole magnets, EQ (Extraction Q-magnet) which make flat beam and RQ (Ripple Q-magnet) which reject the high frequent ripple noise. The feedback system, which is using Digital Signal Processor (DSP), makes a ramping pattern for EQ and RQ from spill beam monitor. The extraction magnets and feedback device were installed in September 2009, and spill feedback study were successfully started from the beam time in October 2009. Here we report the operation status of magnets and first study of beam commissioning with spill feedback.
CERN, Geneva
Within the scope of the LHC injector upgrade, it is proposed to replace the present injector chain by new accelerators, Linac4, SPL and PS2, for which new beam transfer lines are required. The beam properties and requirements for each of the lines are summarized. The original design of the beam lines has been fully reconsidered due to the very demanding constraints on the beam line layouts at the PS2 injection / extraction regions and a new straight section of the PS2 which led to a much improved beam line geometry. The relevant modifications and optics designs are described and a preliminary specification of the beam line equipment is also given.
CERN, Geneva
A new design of the injection-extraction straight section for PS2 has been made, motivated by problematic intersections of the PS2 transfer lines, potential gain in drift length for the beam transfer systems and reduction of the total straight section length. The new straight contains two injection systems with separate beam lines and three extraction systems to the SPS sharing a single beam line, together with an extracted "waste" beam from the H- injection with its line to a beam dump. A symmetric doublet structure was chosen, with a reduced number of cells and quadrupoles. The optics solutions are described and the matching and tuning flexibility investigated. The implications for the different injection and extraction systems and transfer lines will be discussed, together with the specific issues of integration into the overall lattice.
CERN, Geneva
TU Vienna, Wien
EBG MedAustron, Wr. Neustadt
The MedAustron facility, to be built in Wiener Neustadt (Austria), will provide protons and different types of ions for cancer therapy and research. Ten different types of bumpers, septa and kickers will be used in the low energy beam transfer line, the synchrotron and the high energy extraction lines. They are presently being designed in collaboration with CERN. Both 2D and 3D finite element simulations have been carried out to verify and optimize the field strength and homogeneity for each type of magnet and, where applicable, the transient field response. The detailed designs for the injection and dump bumpers, the magnetic septa and the fast chopper dipoles are presented. A novel design for the electrostatic septa is outlined.
GSI, Darmstadt
NSCL, East Lansing, Michigan
Electron Cyclotron Resonance Ion Sources (ECRIS) are increasingly used as ion source for different types of accelerator because of their high current densities for highly charged ions. To investigate the ion beam quality, normally delivered to the RFQ of the high charge state injector at GSI, we had the chance to install a viewing target close to the position of ion beam injection into the RFQ. The profile visible on the viewing target could be recorded through a regular glass window by a simple camera outside the vacuum. The RFQ itself has been removed for these measurements. We have found a highly structured ion beam distribution at that position. These structures, already caused by the hexapolar field within the ion source have already been observed directly behind the extraction. They are transported through the beam line without becoming homogeneous, which indicates a high degree of space charge compensation for that cw-beam. If the full beam line is mastered by the dipole, all charge states show similar ion beam distribution on the target for a given extraction voltage. This is also a hint, that the structures have been produced within the source already.
Fermilab, Batavia
The NOνA Experiment will construct a detector optimized for electron neutrino detection in the existing Neutrino at Main Injector (NuMI) beamline. The NuMI beamline is capable of operating at 400 kW of primary beam power and the upgrade will allow up to 700 kW. Ceramic beam tubes are utilized in numerous kicker magnets in different accelerator rings at Fermilab. Kovar flanges are brazed onto each beam tube end, since kovar and high alumina ceramic have similar expansion curves. The tube, kovar flange, end piece, and braze foil alloy brazing material are stacked in the furnace and then brazed. The most challenging aspect of fabricating kicker magnets in recent years have been making hermetic vacuum seals on the braze joints between the ceramic and flange. Numerous process variables can influence the robustness of conventional metal/ceramic brazing processes. The ceramic-filler metal interface is normally the weak layer when failure does not occur within the ceramic. Differences between active brazing filler metal and the moly-manganese process will be discussed along with the applicable results of these techniques used for Fermilab production kicker tubes.
CERN, Geneva
IN2P3 IPNL, Villeurbanne
INFN/LNL, Legnaro (PD)
Istituto Nazionale di Fisica Nucleare, Milano
The CNGS facility (CERN Neutrinos to Gran Sasso) aims at directly detecting muon to tau neutrino oscillations. An intense muon-neutrino beam (1017 muon neutrinos/day) is generated at CERN and directed over 732km towards the Gran Sasso National Laboratory, LNGS, in Italy, where two large and complex detectors, OPERA and ICARUS, are located. CNGS is the first long-baseline neutrino facility in which the measurement of the oscillation parameters is performed by observation of the tau-neutrino appearance. The facility is approved for a physics program of five years with a total of 22.5·1019 protons on target. Having resolved successfully some initial issues that occurred since its commissioning in 2006, the facility had its first complete year of physics in 2008. By the end of the 2009 physics run the facility will have delivered in total more than 5·1019 protons on target corresponding to ~2-3 tau neutrino events in the OPERA detector. The experiences gained in operating this 500 kW neutrino beam facility along with highlights of the beam performance in 2008 and 2009 are discussed.
INFN/LNL, Legnaro (PD)
In singly charged positive ion sources, the study of beam extraction is greatly simplified by the existence of a well defined place for plasma to beam transition, given by the well known Bohm criterion, where the ion flow speed equals the speed of sonic perturbation, known as Bohm speed. Most of the ion extraction simulation codes are implicity based on the concept of quasi neutrality in the plasma region, as limited by the Bohm criterion. In negative ion source the existence of an electron coextracted beam and of a magnetic filter makes the relevant speed less clear. Moreover there are several scale lengths to be considered: the Debye length, that is typically 0.01 mm, the electron and ion gyroradius, the H- scattering, absorbtion and production length. In the development of negative ion source for NBI injector for ITER, the production of H- at wall and the negative sheath so generated is also important. A critical evaluation of these regimes is obtained with 1D (one space dimension) models, mostly restricted to magnetic filter parallel to the extraction wall. Some remarks on 2D simulation codes is also given.
INFN/LNL, Legnaro (PD)
Consorzio RFX, Associazione Euratom-ENEA sulla Fusione, Padova
The development of neutral beam injectors (NBI) for tokamak like the ITER project and beyond requires high performance and huge negative ion sources (40 A of D- beam required); it was recently accepted that inductive plasma coupled (ICP) radiofrequency sources are the preferred option. It is therefore useful to have a moderate size source of modular design to test and verify both construction technologies and components and simulation codes; here the NIO1 design (60 kV, 9 beamlets of 15 mA H- each) and construction status are described. Source is assembled from disk shaped modules, for rapid replacement; the beamlets are arranged in 3 times 3 square matrix so that 90 degree rotation of modules is possible and allows to cross or to align the magnetic filters used in the source. The 2 MHz rf coil and the rf window are a simply replaceable module. Extensive rf absorption and magnetic coil simulations were performed. Related beam simulation and fast emittance scanner development are described elsewhere.
The University of Tokyo, Institute of Physics, Tokyo
HU/AdSM, Higashi-Hiroshima
MPQ, Garching, Munich
RIKEN, Wako, Saitama
Hiroshima University, Graduate School of Advanced Sciences of Matter, Higashi-Hiroshima
Tokyo University of Science, Tokyo
University of Tokyo, Chiba
KEK, Tsukuba
The ASACUSA collaboration at CERN has been developed a unique Mono-energetic Ulta-Slow Antiproton beam Source for High-precision Investigation (MUSASHI) for collision studies between antiproton and atoms at very low energy region, which also used as an intense ultra-low energy antiproton source for the synthesis of antihydrogen atoms in order to test CPT symmetry. MUSASHI consists of a multi-ring electrode trap housed in a bore surrounded by a superconducting solenoid, which works with a sequential combination of the CERN Antiproton Decelerator and the Radio-Frequency Quadrupole Decelerator. GM-type refrigerators were used to cool the solenoid and also the bore at 4K to avoid losses of antiprotons with residual gasses. Up to 1.8 millions of antiprotons per one AD cycle were successfully trapped and cooled. MUSASHI achieved to accumulate more than 12 millions of cold antiprotons by stacking several AD shots. Such cooled antiprotons were extracted as 150 or 250eV beams with various bunch lengths from 2 micoroseconds to 30 seconds long, whose energy width was the order of sub-eV. The beam intensity was enhanced by a radial compression technique for the trapped antiproton cloud.
RIKEN Nishina Center, Wako
The superconducting ECR ion source enabled to use a 28 GHz microwave source had been developed to provide intense beam of highly charged heavy ions like U35+ to the RIKEN RI-beam factory (RIBF) since 2007. The first plasma was lit in May of 2009 and it was succeeded in providing the uranium beam to the RIBF in December. In this operation, uranium ions were supplied with sputter method and two 18 GHz microwave sources were used. The beam intensity of the uranium ion exceeded 14μAmps, which was more than five times larger than that for 18 GHz ECR ion source of a usual type. The extraction system consists of the accel-decel electrode system, a solenoid coil and a 90 degreeanalyzing magnet. We measured the profiles and emittances of the extracted beams for several ion species and compared with the calculated results with 'OPERA-3d' including space charge effect. And we shall discuss the beam dynamics at the extraction region such as the relationship between the beam emittance and the operating parameters.
JINR, Dubna, Moscow Region
VNIIEF, Sarov (Nizhnii Gorod)
JINR/LHE, Moscow
The Electron String Ion Source (ESIS) developed at JINR is effectively used here during the last decade. The Tubular Electron String Ion Source (TESIS) has been put forward recently to obtain a 1-2 orders of magnitude increase in the ion output as compared with ESIS. The project is aimed at creating TESIS and studying the electron string in the tubular geometry. The new tubular source with a superconducting solenoid up to 5 T is under construction now. The method of the off axis TESIS ion extraction will be realized to get TESIS beam emittance comparable with ESIS emittance. It is expected that this new TESIS will meet all rigid conceptual and technological requirements and should provide an ion output approaching 10 mA of Ar16+ ions in the pulsed mode and about 10 μA of Ar16+ ions in the average current mode. Design, construction and test of separate TESIS systems are discussed in this report.
STFC/RAL/ISIS, Chilton, Didcot, Oxon
The Front End Test Stand (FETS) under construction at the Rutherford Appleton Laboratory is the UK's contribution to research into the next generation of High Power Proton Accelerators (HPPAs). Running at duty cycles of up 50 Hz with pulse lengths of 2 ms are required. This paper presents initial Hminus beam currents and emittance measurements for long pulse lengths.
Muons, Inc, Batavia
ORNL, Oak Ridge, Tennessee
Development of novel modifications of H- source designs is proposed. The new source will be an advanced version of a Penning DT SPS (Dudnikov-Type Penning Surface Plasma Source) which will generate brighter beam in noiseless discharge, deliver up to 20 mA average current with better electrode cooling using new materials, and have longer lifetime, fast beam chopping capability, and reduced cesium loss.
Muons, Inc, Batavia
UMD, College Park, Maryland
ORNL, Oak Ridge, Tennessee
In this project we are developing an RF H- surface plasma source which will synthesize the most important developments in the field of negative ion sources to provide high pulsed and average current, high brightness, good lifetime, high reliability, and higher power efficiency. We describe two planned modifications to the present SNS external antenna source in order to increase the plasma density near the output aperture: 1) replacing the present 2 MHz plasma-forming solenoid antenna with a 13 MHz saddle-type antenna and 2) replacing the permanent multicusp magnetic system with a weaker electro-magnet. Progress of this development will be presented.
INFN-Ferrara, Ferrara
UNIFE, Ferrara
Univ. degli Studi di Padova, Padova
INFN/LNL, Legnaro (PD)
JINR, Dubna, Moscow Region
Channeling in bent crystals is a technique with high potential to steer charged-particle beams for several applications in accelerators physics. Revisited methods of silicon micromachining techniques allowed one to realize a new generation of crystals. Characterizations using x-ray diffraction, atomic force microscopy, high resolution transmission electron microscopy and ion beam analysis techniques, showed high quality of the crystals. A specifically designed holder allowed to mechanically bend a crystal at given curvature and remove unwanted torsion. Characterization of such crystals with 400 GeV at CERN H8 external line highlighted 85% single-pass efficiency. A selected crystal has been installed inside the SPS ring in the environment of the CERN experiment UA9 and successfully employed for collimation of the circulating beam.
On behalf of UA9 collaboration
CERN, Geneva
INFN-Roma, Roma
The UA9 experiment was performed in 6 MDs from May to November 2009 with the goal of studying the collimation properties of a crystal in the framework of a future exploitation in the LHC collimation system. An important parameter evaluated for the characterization of the crystal collimation is the efficiency of halo extraction when the crystal is in channeling mode. In this paper it is explained how this efficiency can be measured using a pixel detector, the Medipix, installed in the Roman Pot of UA9. The number of extracted particles counted by the Medipix is compared with the total number of circulating particles measured by the Beam Current Transformers (BCTs): from this comparison the efficiency of the system composed by the crystal, used in channeling mode, and a tungsten absorber is proved to be greater than 85%.
STFC/RAL, Chilton, Didcot, Oxon
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire
BNL, Upton, Long Island, New York
STFC/DL, Daresbury, Warrington, Cheshire
UBC & TRIUMF, Vancouver, British Columbia
Fermilab, Batavia
Brunel University, Middlesex
CERN, Geneva
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
TRIUMF, Vancouver
CEA, Gif-sur-Yvette
Imperial College of Science and Technology, Department of Physics, London
JAI, Oxford
The Electron Model for Many Applications (EMMA) will be the World's first non-scaling FFAG and is under construction at the STFC Daresbury Laboratory in the UK. Construction is due for completion in March 2010 and will be followed by commissioning with beam and a detailed experimental programme to study the functioning of this type of accelerator. This paper will give an overview of the motivation for the project and describe the EMMA design and hardware. The first results from commissioning will be presented in a separate paper.
CEA, Gif-sur-Yvette
Brunel University, Middlesex
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
JAI, Oxford
The Electron Model for Many Applications FFAG (EMMA) has been the object of extensive beam dynamics simulations during its design and construction phases, using the ray-tracing code Zgoubi, which has been retained as the on-line simulation engine. On the other hand EMMA commissioning requires further advanced beam dynamics studies as well as on-line and off-line simulations. This contribution reports on some aspects of the studies so performed during the last months using Zgoubi.
CEA, Gif-sur-Yvette
BNL, Upton, Long Island, New York
Brunel University, Middlesex
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire
UMAN, Manchester
The EMMA (Electron Model for Many Applications) FFAG experiment at Daresbury will involve on-line modeling (a ‘‘Virtual EMMA'') based on stepwise ray-tracing methods. Various aspects of the code of concern and of its interfacing to real world - machine and users - are addressed.
University of Oslo, Oslo
CERN, Geneva
NTNU, Trondheim
The CLIC Test Facility 3 Test Beam Line is the first prototype for the CLIC drive beam decelerator. Stable transport of the drive beam under deceleration is a mandatory component in the CLIC two-beam scheme. In the Test Beam Line more than 50% of the total energy will be extracted from a 150 MeV, 28 A electron drive beam, by the use of 16 Power Extraction and Transfer structures. A number of experiments are foreseen to investigate the drive beam characteristics under deceleration in the Test Beam Line, including beam stability, beam blow up and the efficiency of the power extraction. General benchmarking of decelerator simulation and theory studies will also be performed. Specially designed instrumentation including precision BPMs, loss monitors and a time-resolved spectrometer dump will be used for the experiments. This paper describes the experimental program foreseen for the Test Beam Line, including the relevance of the results for the CLIC decelerator studies.
LAL, Orsay
KEK, Ibaraki
SLAC, Menlo Park, California
The purpose of ATF2 is to deliver a beam with stable very small spotsizes as required for future linear colliders such as ILC or CLIC. To achieve that, precise controls of the aberrations such as dispersion and coupling are necessary. Theoretically, the complete reconstruction of the beam matrix is possible from the measurements of horizontal, vertical and tilted beam sizes, combining skew quadrupole scans at several wire-scanner positions. Such measurements were performed in the extraction line of ATF2 in May 2009. We present analysis results attempting to resolve the 4X4 beam matrix and discuss the experimental limitations of 4D emittance measurements with wire scanners.
Kyungpook National University, Daegu
Proton Engineering Frontier Project (PEFP) Linac has a plan of the addition of 1 GeV RCS ring. The lattice of the rapid cycling synchrotron is affected by a non-linear beam dynamics. In this study, we investigated about non-linear dynamics due to sextupoles in PEFP RCS. Notably, we investigated about 3rd integer resonance due to sextupoles. To slowly and continuously extract the proton beam, we utilize the 3rd integer resonance. For the reason, we investigated non linear beam dynamics due to 3rd integer resonance and slow extraction system by using of MAD8.
IUCF, Bloomington, Indiana
The Advanced eLectron-PHoton fAcility (ALPHA) is under construction to support Crane Naval Center's radiation effect testing program. This paper reports the design of injection and extraction beamlines for the ALPHA and discusses the nonlinear beam spreader which is used to convert transverse Gaussian beam distribution into uniform rectangular beam distribution.
KEK, Ibaraki
J-PARC, KEK & JAEA, Ibaraki-ken
During the early J-PARC Main Ring commissioning the emittance growth at the injection energy, caused by the field leakage of the slow extraction septums, has been observed. By using the measured field data in the J-PARC Main Ring computational model we perform the analysis of the resonance excitation for the 'bare' working points around the 3rd order horizontal resonance, used for the slow extraction of the accelerated beam. The space charge effects of the low energy beam with the moderate beam power are taken into this analysis. Some possible ways to reduce the transverse emittance dilution and the particle losses during the machine operation for the 'hadron' experiments are discussed.