Kyoto ICR, Uji, Kyoto
A compact neutron source using Li(p,n) or Be(p,n) reaction is proposed. The proton linac consists of ECR ion source, LEBT(Low Energy Beam Transport), RFQ linac and post accelerator. We assume that energy of the proton beam is 3MeV and its peak current is 40 mA operated at the repetition rate is 25Hz with the pulse width of 1ms. The beam from the ion source should be matched to the RFQ, where solenoid coils can handle the large current beam in this LEBT section. To reduce energy consumption in LEBT we're trying to design the Hybrid Electromagnet that consists of solenoid coils and permanent magnets. We use PANDIRA, TRACE-2D, and PBGUNS computer codes in order to simulate the magnetic field and the beam transport through LEBT. In this paper the design of this magnet and the result of its beam matching based on simulation will be presented.
KEK, Ibaraki
KEK is studying the design of the interaction region quadrupoles for the SuperKEKB of which the two beams of 4GeV/7GeV for LER/HER have a crossing angle of 83 mrad. For each beam, the final beam focusing system consisting of superconducting and permanent magnets is studied. The superconducting quadrupoles close to the interaction point for each beam are located in the compensation superconducting solenoid which cancels the solenoid field by the particle detector, Belle. These magnet parameters are optimized to obtain higher luminosity. In this paper, the design progress of final focusing system and magnets will be reported.
CIEMAT, Madrid
CEA, Gif-sur-Yvette
FZJ, Jülich
The IFMIF-EVEDA accelerator will handle a 9 MeV, 125 mA continuous wave (CW) deuteron beam which aims to validate the technology that will be used in the future IFMIF accelerator. The Linac design is based on superconducting Half Wave Resonators (HWR) operating at 4.4 K. Due to space charge associated to the high intensity beam, a strong superconducting focusing magnet package is necessary between cavities, with nested steerers and a Beam Position Monitor (BPM). First of all, this paper describes the preliminary study to choose between two quadrupoles or one solenoid as focusing device, both using NbTi wire. The solenoid shows more advantages, mainly associated to available space and reliability. Then, electromagnetic and mechanical design of the solenoid and the steerers are reported. Special care is taken in order to fulfil the fringe field limit at the cavity flange. An active shield configuration using an anti-solenoid has been adopted, avoiding remnant magnetization associated to passive shielding materials.
Fermilab, Batavia
Helical Solenoids (HS) were proposed for a muon beam ionization cooling. There are substantial up to 30 MeV/m energy losses during passing the muon beam through an absorber. The main issue of such system is the energy recovery. A conventional RF cavity has diameter which is too large to be placed inside HS. In the paper presented results of dielectric filled RF cavity design. The proposed cavity has helical configuration. Presented Helical Cooling Channel module design which includes: high pressure vessel, RF cavity, and superconducting HS. Discussed parameters of this module sub-systems and shown results of muon beam tracking in combined magnetic and electric 3D fields.
Fermilab, Batavia
Muons, Inc, Batavia
The Helical Cooling Channel (HCC) is a technique proposed for six-dimensional (6D) cooling of muon beams. The HCC for muon collider and some other applications is usually divided into several sections each with progressively stronger fields, smaller aperture, and shorter helix period to achieve the optimal muon cooling rate. Novel magnet design concepts based on simple coils arranged in a helical solenoid configuration have been developed to provide HCC magnet systems with the desired parameters. The level of magnetic field in the HCC high-field sections suggests using a hybrid coil structure with High Temperature Superconductors (HTS) in the innermost coil layers and Nb3Sn superconductor in the outer coil layers. The development of the concepts and engineering designs of hybrid helical solenoids based on advanced superconductor technologies, with special emphasis on the use of HTS for high fields at low temperature is the key step towards a practical HCC. This paper describes the conceptual designs and parameters of a short HTS model of a hybrid helical solenoid, and discusses the structural materials choices, fabrication techniques, and first test results.
Muons, Inc, Batavia
North Carolina State University, Raleigh, North Carolina
YBCO superconductors originally developed for high temperature operation carry significant critical current even in the presence of extremely high magnetic field when operated at low temperature. The final stage of phase space cooling for a muon collider uses a solenoid magnet with fields approaching 50 T. As part of an R&D effort we present measurements of mechanical and electromechanical properties of the YBCO conductor. We examine the critical current verses magnet field angle at 4.2 K in a magnetic field. Quench properties of the conductor such as minimum quench energy threshold and quench propagation velocity will be measured to establish safe operational conductions for the muon cooling magnets. In this paper we describe a conceptual picture for a high field solenoid to be used for muon phase space cooling that incorporates these low temperature properties of YBCO.
LBNL, Berkeley, California
ICST, Harbin
Tests of the spectrometer solenoids have taught us some important lessons. The spectrometer magnet lessons learned fall into two broad categories that involve the two stages of the coolers that are used to cool the magnets. On the first spectrometer magnet, the problems were centered on the connection of the cooler 2nd-stage to the magnet cold mass. On the second spectrometer magnet, the problems were centered on the cooler 1st-stage temperature and the connections between leads, the cold mass support intercept, and the shields to the cooler first-stage. If the cooler 1st-stage temperature is too high, the refrigerator will not produce full 2nd stage cooling. If the 1st-stage temperature is too high, the temperature of the top of the HTS leads. As a result, more heat goes into the 4 K cold mass and the temperature margin of the top of the HTS leads is too small, which are in a magnetic field. The parameters that affect the magnet cooling are compared for the MICE coupling magnet and the spectrometer magnet.
LBNL, Berkeley, California
The Muon Ionization Cooling Experiment (MICE), an international collaboration sited at Rutherford Appleton Laboratory (RAL) in the UK, will demonstrate ionization cooling in a section of a realistic cooling channel using a muon beam. A five-coil superconducting spectrometer solenoid magnet will provide a 4 tesla uniform field region at each end of the cooling channel. Scintillating fiber trackers within the 400 mm diameter magnet bore tubes measure the emittance of the beam as it enters and exits the cooling channel. Each of the identical 3 meter long magnets incorporates a three-coil spectrometer magnet section and a two-coil section that matches the solenoid uniform field into the MICE cooling channel. The cold mass, radiation shield and leads are kept cold by means of three two-stage cryocoolers and one single-stage cryocooler. After incorporating several design changes to improve the magnet cooling and reliability, the fabrication and acceptance testing of the spectrometer solenoids has been completed. The key features of the spectrometer solenoid magnets are presented along with the details of a finite element model used to predict the thermal performance of the magnets.
BNL, Upton, Long Island, New York
In polarized proton operation the luminosity of RHIC is limited by the head-on beam-beam effect, and methods that mitigate the effect will result in higher peak and average luminosities. Two electron lenses, one for each ring, are being constructed to partially compensate the head-on beam-beam effect in the two rings. An electron lens consists of a low energy electron beam that creates the same amplitude dependent transverse kick as the proton beam. We discuss design consideration, present the main parameters, and estimate the performance gains.
CEA, Gif-sur-Yvette
CIEMAT, Madrid
FZJ, Jülich
The IFMIF project aims to build a high intensity material irradiation facility which one of the main components is a high intensity deuteron accelerator. A prototype of this accelerator will be built in Rokkasho in Japan. It includes a cryomodule composed of 8 superconducting cavities (HWR) powered by 200 kW couplers to accelerate the deuteron beam from 5 MeV to 9 MeV. The beam is focused inside the cryomodule by 8 superconducting solenoids. The cryomodule design has to respect some severe beam dynamics requirements, in particular a restricted space for the component interfaces and an accurate alignment to be kept during cooling down. A double cryogenic system has been designed as it is necessary to control the cavity cooling independently from the solenoid one. The cryomodule design should also be compatible with its environment in the Rokkasho building. This paper gives then a general overview of the 1rst cryomodule current design and its interfaces. It defines the concept chosen for the Cryogenic System, explains the method foreseen for the assembly and alignment and describes the integration study in Rokkasho.
University of Warwick, Coventry
Fundación Tekniker, Elbr (Guipuzkoa)
Bilbao, Faculty of Science and Technology, Bilbao
Fundación TEKNIKER, Eibar (Gipuzkoa)
STFC/RAL, Chilton, Didcot, Oxon
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
STFC/RAL/ISIS, Chilton, Didcot, Oxon
Elytt Energy, Madrid
Imperial College of Science and Technology, Department of Physics, London
The Front End Test Stand (FETS) at the Rutherford Appleton Laboratory is intended to demonstrate the early stages of acceleration (0-3 MeV) and beam chopping required for high power proton accelerators, including proton drivers for pulsed neutron spallation sources and neutrino factories. A Low Energy Beam Transport (LEBT), consisting of three solenoids and four drift sections, is used to transport the H- beam from the ion source to the FETS Radio Frequency Quadrupole. We present the status of the installation and commissioning of the LEBT, and compare particle dynamics simulations with preliminary measurements of the H- beam transport through the LEBT.
STFC/RAL/ISIS, Chilton, Didcot, Oxon
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
Imperial College of Science and Technology, Department of Physics, London
The front end test stand (FETS) [1] is entering the next stage of construction and commissioning, with the three-solenoid magnetic low energy beam transport (LEBT) line being installed. A thorough characterization of the beam leaving the Penning H- ion source has been performed. This includes measurements of the beam current using toroids and of the transverse emittance using slit-slit scanners. These measurements are performed over a wide range of source discharge and extraction parameters in order to understand how the transmission may be improved. Comments on the quality of the beam to be injected into the FETS radio frequency quadrupole (RFQ) are given.
FZJ, Jülich
BINP SB RAS, Novosibirsk
The 2 MeV electron cooling system for COSY-Jülich was proposed to further boost the luminosity even in presence of strong heating effects of high-density internal targets. The project is funded since mid 2009. Manufacturing of the cooler components has already begun. The space required for the 2 MeV cooler is being made available in the COSY ring. The design and construction of the cooler is accomplished in cooperation with the Budker Institute of Nuclear Physics in Novosibirsk, Russia. The 2 MeV cooler is also well suited in the start up phase of the High Energy Storage Ring (HESR) at FAIR in Darmstadt. It can be used for beam cooling at injection energy and is intended to test new features of the high energy electron cooler for HESR. Two new prototypes of the modular high voltage system were developed, one consisting of gas turbines the other based on inductance-coupled cascade generators. The new 2 MeV electron cooler is described in detail and tests of components are reported.
Kyoto ICR, Uji, Kyoto
Kyoto IAE, Kyoto
NIRS, Chiba-shi
In order to achieve three dimensional crystal beam, laser cooling forces are required not only in the longitudinal direction, but also in the transverse directions. With the resonance coupling method*, transverse temperature is transmitted into longitudinal direction, and we have already demonstrated horizontal laser cooling experimentally **. In the present paper, we describe an approach to extend this result to three dimensional cooling. The vertical cooling requires that the horizontal oscillation couples with the vertical oscillation. For achieving horizontal-vertical coupling, a solenoid in electron beam cooling apparatus is utilized with an experiment (Qx=2.07,Qy=1.07). For various solenoidal magnetic fields from 0 to 40Gauss, horizontal and vertical betatron tunes are measured by beam transfer function. For a certain region of the solenoidal magnetic field, these tunes are mixed up each other. By optimization of such a coupling, we aim to proceed to three dimensional laser cooling.
* H. Okamoto Phys. Rev. E 50, 4982 (1994)
** H. Souda et.al.,contribution to this conference
Fermilab, Batavia
JLAB, Newport News, Virginia
Muons, Inc, Batavia
Fast muon beam six dimensional (6D) phase space cooling is essential for muon colliders. The Helical Cooling Channel (HCC) uses hydrogen-pressurized RF cavities imbedded in a magnet system with solenoid, helical dipole, and helical quadrupole components that provide the continuous dispersion needed for emittance exchange and effective 6d beam cooling. A series of HCC segments, each with sequentially smaller aperture, higher magnetic field, and higher RF frequency to match the beam size as it is cooled, has been optimized by numerical simulation to achieve a factor of 105 emittance reduction in a 300 m long channel with only a 40% loss of beam. Conceptual designs of the hardware required for this HCC system and the status of the RF studies and HTS helical solenoid magnet prototypes are described.
SINAP, Shanghai
A new beam profile diagnostic system based on industrial Ethernet has been installed in Shanghai Deep Ultraviolet Free Electron Laser (SDUV-FEL) facility recently. By choosing GigE Vision cameras, the system provides better image quality over a long distance than before. Beam images are captured from the beam profile monitors which are controlled by air cylinders or step motors. In order to fit for the system expansibility and curtail the cables, all devices are operated through the Ethernet and distributed along the FEL facility. The approach to the design of the hardware and software will be described in this paper. Applications and experiment results will be shown in this paper as well.
OXFORDphysics, Oxford, Oxon
INFN MIB, MILANO
The international Muon Ionization Cooling Experiment (MICE) will carry out a systematic investigations of ionization cooling of a muon beam. As the emittance measurement will be done on a particle-by-particle basis, a sophisticated beam instrumentation is needed to measure particle coordinates and timing vs RF. A PID system based on three time-of-flight detectors, two Aerogel Cerenkov counters and a KLOE-like calorimeter has been constructed in order to keep beam contamination (e, π) well below 1 %. The MICE TOF system will measure timing with a resolution better than 60 ps per plane, in a harsh environment due to high particle rates, fringe magnetic fields and RF backgrounds. Performances in beam of all detectors will be shown, as also future upgrades.
Hiroshima University, Higashi-Hiroshima
Osaka University, Graduate School of Science, Osaka
HU/AdSM, Higashi-Hiroshima
Space charge effects due to the strong Coulomb interactions expected in high intensity accelerator beams result in undesirable beam degradation and radio-activation of the vacuum tubes through halo formations. Various space charge effects have been studied intensively with particle simulations. This is partly because the analytical formulation of the nonlinear evolution in high intensity beams is not possible in general cases. And the systematic study of space charge effects with the real accelerators is not feasible. Although the development of computation environment is outstanding, some approximations are still necessary so far. Thus, it was proposed to use solenoid traps and linear Paul traps for investigating some properties of space charge dominated beams. The key idea is that the charged particles in these traps are physically equivalent with a beam in a FODO lattice. Some experimental results have been reported with the use of Paul traps. Here, a solenoid trap with a beam imaging system composed of a charge coupled device camera and a phosphor screen was employed to study the mismatch induced oscillations of a space charge dominated beams.
SLAC, Menlo Park, California
We present an approach for compensating adverse effects of the detector solenoid in the SuperB Interaction Region (IR). We place compensating solenoids around the IR quadrupole magnets to reduce the magnetic fields nearly to zero. This allows more operational headroom for superconducting IR magnets and avoids saturation of ferric IR magnets. We place stronger compensating solenoids between IR magnets to reverse the magnetic field direction. This allows adjusting the total integrated solenoid field to zero, which eliminates coordinate plane rotation and reduces vertical beam displacements in the IR.
SLAC, Menlo Park, California
Cockcroft Institute, Warrington, Cheshire
INFN/LNF, Frascati (Roma)
BINP SB RAS, Novosibirsk
The availability of longitudinally polarized electrons is an important aspect of the design of the proposed SuperB project at LNF Frascati. Spin rotators are an integral part of the design of the Interaction Region (IR). We have chosen a solenoid-dipole design; at the 4.18 GeV nominal energy this is more compact that a design purely based on dipole magnets. Integration with the local chromaticity correction of the ultra-low beta* IR has been achieved. The spin rotators are symmetric about the Interaction Point, this design saves a significant amount of length as the dipoles become a part of the overall 360 deg. bend. The layout leaves limited opportunity to setup the optics for minimum depolarization; this is acceptable since beam life time in SuperB at high luminosity is only about 5 min and up-to 90% polarized electrons will be injected continuously. In this way an average beam polarization of about 70% is maintained. Simulations and analytic estimates with the DESY code SLICKTRACK and other codes indicate such operation is feasible from a spin-dynamics point of view. The paper will discuss the overall spin-rotator design as well as the spin dynamics in the ring.
CASA, newport news
JLAB, Newport News, Virginia
A unique design feature of a polarized Medium Energy Electron-Ion Collider (MEIC) based on CEBAF is its 'Figure-8' storage rings for both electrons and ions, which significantly simplifies beam polarization maintenance and manipulation. While electron (positron) polarization is maintained vertical in arcs of the ring, a stable longitudinal spin at four collision points is achieved through solenoid based spin rotators and horizontal orbit bends. The proposed MEIC lattice was developed in order to preserve a very high polarization (more than 70%) of the electron beams injected from the CEBAF machine. The otherwise coupled beam trajectory due to solenoids used in the spin rotators was decoupled by design. Aspin matching technique needs to be implemented in order to enhance quantum self-polarization and minimize depolarization effects.
KEK, Ibaraki
The near beam electron cloud density in a magnetic field was estimated with a simple electron current detector at KEKB LER. The estimation is based on the assumption that high energy electrons which hit a chamber wall come directly from the region around the beam after the interaction with a circulating bunch. The first successful application of this idea for a drift space was reported at PAC05 by the authors. In a solenoid field of 50 G, the near beam cloud density is reduced by about four orders of magnitude compared to the no field case. In a quadruple magnet, the density around the beam is by two orders of magnitude lower than the density in a typical drift space, as most simulations show.
Kyoto IAE, Kyoto
Aiming at realizing a short period undulator with strong magnetic field, we have proposed a Bulk HTSC (high temperature superconductor) Staggered Array Undulator which consists of bulk high temperature superconductor magnets with a staggered array configuration. The experiment with the prototype undulator at 77 K shows this configuration can be applicable to real undulator. We also estimated the magnetic performance of real device by calculations with a loop current model based on Bean model of superconductor. Although end field termination is required for practical use, traditional methods are not applicable for the bulk HTSCs. We found that the end field termination can be realized by controlling the shape and size of bulk HTSCs at the end section by numerical calculation using the loop current model. In the conference, the calculation and experimental result of end field termination will be presented.
CERN, Geneva
IMFD, Freiberg
KIT, Karlsruhe
FZK, Karlsruhe
Two damping rings (e+, e-) are foreseen for the CLIC injection chain. In each damping ring 76 two meter long wigglers will be installed. The short period (40-50 mm), combined with a gap larger than 14 mm and a requested field in the mid-plane BPeak > 2 T requires the usage of superconducting technologies to meet these requirements. To demonstrate the feasibility of this wiggler design a short-model vertical racetrack wiggler (40 mm period; 16 mm gap) was built and successfully tested at CERN. The wiggler carries a current of 730 A and 910 A and reaches a mid-plane peak field of Bpeak = 2 T and Bpeak = 2.5 T at 4.2 K and 1.9 K, respectively. The results show that the wiggler model meets the magnetic requirements of the CLIC damping rings at 1.9 K. The paper will also discuss the improvements we propose to enhance the performance in order to meet the CLIC specifications also at 4.2 K.
CEA, Gif-sur-Yvette
The International Linear Collider reference design is based on a collision scheme with a 14 mrad crossing angle. Consequently, the detector solenoid and the machine axis do not coincide. It provokes a position offset of the beam at the Interaction Point in addition to a beam size growth. These effects are modified by the insertion of the anti-DID (Detector Integrated Dipole) aiming at reducing background in the detector. Furthermore a crab cavity is necessary to restore a 'head on' like collision, leading to higher luminosity. This introduces new beam distortions. In this paper, optics studies and simulations of beam transport in the Interaction Region taking these elements into account are presented. Correction schemes of the beam offset and beam size growth are exposed and their associated tolerances are evaluated.
CERN, Geneva
The main detector solenoid and associated magnets can have an important impact on the CLIC luminosity. These effects are discussed for different solenoid designs. In particular, the luminosity loss due to incoherent synchrotron radiation in the experiment solenoid and QD0 overlap is evaluated. The impact of the AntiDiD (Anti Detector integrated Dipole) on luminosity and compensated techniques on beam optic distortion are also discussed.
Imperial College of Science and Technology, Department of Physics, London
Muon ionization cooling provides the only practical solution to prepare high brilliance beams necessary for a neutrino factory or muon colliders. The muon ionization cooling experiment (MICE)* is under development at the Rutherford Appleton Laboratory (UK). It comprises a dedicated beam line to generate a range of input emittance and momentum, with time-of-flight and Cherenkov detectors to ensure a pure muon beam. A first measurement of emittance is performed in the upstream magnetic spectrometer with a scintillating fiber tracker. A cooling cell will then follow, alternating energy loss in liquid hydrogen and RF acceleration. A second spectrometer identical to the first one and a particle identification system provide a measurement of the outgoing emittance. In May 2010 it is expected that the beam and most detectors will be commissioned and the time of the first measurement of input beam emittance closely approaching. The plan of steps of measurements of emittance and cooling, that will follow in the rest of 2010 and later, will be reported.
This abstract is submitted by the chear of the MICE speaker bureau. A member of the collaboration will be soon identified to present the poster and added a co-author.
Osaka University, Osaka
The COMET is an experiment to search for the process of muon to electron conversion in a muonic atom, and is in its design phase to be carried out at J-PARC in near future. The experiment uses a long superconducting solenoid channels from a pion production target to a detector system. In order, to study the solenoid channel the g4beamline is used for the magnetic field calculation and beam tracking. This paper reports the status of the simulation studies.
Imperial College of Science and Technology, Department of Physics, London
OXFORDphysics, Oxford, Oxon
In the Muon Ionization Cooling Experiment (MICE) at RAL muons are produced and transported in a dedicated beamline connecting the production point (target) to the diffuser, a mechanism inside the first spectrometer solenoid designed to inflate the initial normalized emittance up to 10 mm rad in a controlled fashion. In order to match the incoming muons to the downstream experiment, covering all the possible values of the emittance-momentum matrix, an optimisation procedure has been devised which is based upon a genetic algorithm coupled to the tracking code G4Beamline. Details of beamline tuning and initial measurements are discussed.
Imperial College of Science and Technology, Department of Physics, London
Fermilab, Batavia
The COherent Muon to Electron Transition (COMET) experiment aims to measure muon to electron conversion with an unprecedented sensitivity of less than 1 in 10 million billion. The COMET experiment was given stage 1 approval by the J-PARC Program Advisory Committee in July 2009 and work is currently underway towards preparing a technical design report for the whole experiment. The need for this sensitivity places several stringent requirements on the beamline, such as, a pulsed proton beam with an extinction level between pulses of 9 orders of magnitude; a 5T superconducting solenoid operating near a high radiation environment; precise momentum selection of a large emittance muon beam and momentum selection and collimation of a large emittance electron beam. This paper will present the current status of the various components of the COMET beamline.
OXFORDphysics, Oxford, Oxon
The Muon Ionization Cooling Experiment is one lattice section of a cooling channel suitable for conditioning the muon beam at the front end of a Neutrino Factory or Muon Collider. Scintillating fibre spectrometers and 50 ps resolution timing detectors provide the unprecedented opportunity to measure the initial and final six-dimensional phase space vectors of individual muons. The capability of MICE to study the evolution of muon beams through a solenoidal lattice will be described.
Fermilab, Batavia
CERN, Geneva
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
Muons, Inc, Batavia
We discuss the design of the muon capture front end of a neutrino factory and present studies of variations of its components. In the front end, a proton bunch on a target creates secondary pions that drift into a capture transport channel, decaying into muons. A sequence of rf cavities forms the resulting muon beams into strings of bunches of differing energies, aligns the bunches to (nearly) equal central energies, and initiates ionization cooling. The cooling section uses absorber material (reducing the 3-D muon momenta) alternating with rf cavities (restoring longitudinal momentum) within strong focusing magnetic fields. The design is affected by limitations on accelerating gradients within magnetic fields. The effects of gradient limitations are explored, and mitigation strategies are presented. Variations of the ionization cooling and acceleration scenarios and extensions toward use in a muon collider are discussed.
Muons, Inc, Batavia
Fermilab, Batavia
A helical cooling channel (HCC) consisting of a pressurized gas absorber imbedded in a magnetic channel that provides solenoidal, helical dipole and helical quadrupole fields has shown considerable promise in providing six-dimensional cooling for muon beams. The energy lost by muons traversing the gas absorber needs to be replaced by inserting RF cavities into the HCC lattice. Replacing the substantial muon energy losses using RF cavities with reasonable gradients will require a significant fraction of the channel length be devoted to RF. However to provide the maximum phase space cooling and minimum muon losses, the HCC should have a short period and length. In this paper we examine an approach where each HCC cell has an RF cavity imbedded in the aperture with the magnetic coils are split allowing for half of the cell length to be available for the RF coupler and other services.
Muons, Inc, Batavia
Fermilab, Batavia
Intense muon beams have many potential applications, including neutrino factories and muon colliders. However, muons are produced as tertiary beams, resulting in diffuse phase space distributions. To make useful beams, the muons must be rapidly cooled before they decay. An idea conceived recently for the collection and cooling of muon beams, namely, the use of a Quasi-Isochronous Helical Channel (QIHC) to facilitate capture of muons into RF buckets, has been developed further. The resulting distribution could be cooled quickly and coalesced into a single bunch to optimize the luminosity of a muon collider. After a brief elaboration of the QIHC concept, some recent developments are described.
LANL, Los Alamos, New Mexico
Many groups are working on muon accelerators for future neutrino factory and muon colliders. One of the applications of muon accelerator is muon radiography which is a promising method to investigate large objects taking advantage of the long penetration lengths of muons. We propose a compact muon accelerator that has a large energy and a phase acceptance to capture relatively low energy pion/muon of 10 - 100 MeV and accelerates them to 200 MeV without any beam cooling. Like an RFQ, mixed buncher/acceleration mode provides phase bunching during the acceleration. Our current design uses 805 MHz zero-mode normal-conducting cavities with 35 MV/m peak field*. The normal conducting cavities are surrounded by superconducting coils that produce 5 T focusing field. We ran Monte Carlo simulations to optimize linac parameters such as frequency and acceleration gradient. Muon energy loss and scattering effects at the cavity windows are studied, too. The simulation showed that about 10 % of the pion/muon injected into the linac can be accelerated to 200 MeV. Further acceleration is possible with superconducting linac.
* S. Kurennoy et al., IPAC 2010.
PU, Princeton, New Jersey
STFC/RAL/ASTeC, Chilton, Didcot, Oxon
STFC/RAL, Chilton, Didcot, Oxon
ORNL, Oak Ridge, Tennessee
CERN, Geneva
EBG MedAustron, Wr. Neustadt
BNL, Upton, Long Island, New York
Fermilab, Batavia
PPPL, Princeton, New Jersey
We report on the analysis of data collected in the MERIT experiment at CERN during the Fall of 2007. These results validate the concept of a free mercury jet inside a high-field solenoid magnet as a target for a pulsed proton beam of 4-MW power, as needed for a future Muon Collider and/or Neutrino Factory.
UCR, Riverside, California
Imperial College of Science and Technology, Department of Physics, London
Sofia University St. Kliment Ohridski, Faculty of Physics, Sofia
The Muon Ionization Cooling Experiment (MICE) is being built at the Rutherford Appleton Laboratory (RAL) to test ionization cooling of a muon beam. Successful demonstration of cooling is a necessary step along the path toward creating future high intensity muon beams in either a Neutrino Factory or Muon Collider. Production of particles in the MICE beamline begins with a titanium target dipping into the ISIS proton beam. The resulting pions are captured, momentum-selected, and fed into a 5T superconducting decay solenoid which contains the pions and their decay muons. Another dipole then selects the final particles for propagation through the rest of the MICE beamline. Within the last year, the MICE target has been redesigned, rebuilt, and has begun operating in ISIS. The decay solenoid has also become operational, dramatically increasing the number of particles in the MICE beamline. In parallel, particle identification detectors have also been installed and commissioned. In this paper, the commissioning of the improved MICE beamline and target will be discussed, including the use of Time-of-Flight detectors to understand the content of the MICE beam between 200 and 444 MeV/c.
BNL, Upton, Long Island, New York
University of Warwick, Coventry
STFC/RAL, Chilton, Didcot, Oxon
UCLA, Los Angeles, California
ORNL, Oak Ridge, Tennessee
SUNY SB, Stony Brok, New York
PU, Princeton, New Jersey
We outline a program of engineering design and simulation for a target station and pion production/capture system for a 4-MW proton beam at the front end of a Muon Collider or a Neutrino Factory. The target system consists of a free liquid-metal (nominally mercury) jet immersed in a high-field solenoid magnet capture system that also incorporates the proton beam dump. Topics to be studied include optimization of proton beam and jet target parameters, of the magnetic configuration for capture and subsequent transport of pions and muons, of the beam dump, of the radiation/thermal shielding of the capture magnets, and of the beam windows.
Fermilab, Batavia
IIT, Chicago, Illinois
LBNL, Berkeley, California
ANL, Argonne
BNL, Upton, Long Island, New York
JLAB, Newport News, Virginia
TThe MuCool RF Program focuses on the study of normal conducting RF structures operating in high magnetic field for applications in muon ionization cooling for Neutrino Factories and Muon Colliders. This paper will give an overview of the program, which will include a description of the test facility and its capabilities, the current test program, and the status of a cavity that can be rotated in the magnetic field which allows for a more detailed study of the maximum stable operating gradient vs. magnetic field strength and angle.
RIKEN Nishina Center, Wako
The RI beam factory at RIKEN Nishina Center needs high intensity of uranium ion beams. We constructed a new injector, RILAC2, which would provide several hundred times higher intensity. As a part of the RILAC2, we designed the low energy beam transport, LEBT, from the superconducting ECR ion source to the RFQ entrance. In this paper we present its requirements and problems, and show our design as the solutions to them. Especially we focus a technique of a pair of two solenoids to treat a rotational operation and a focusing operation independently. Based on this design, the LEBT was completed in March 2010. The RILAC2 will be operational this fall.
Imperial College of Science and Technology, Department of Physics, London
JLAB, Newport News, Virginia
International Design Study for the Neutrino Factory (IDS-NF) assumes the first stage of muon acceleration (up to 900 MeV) to be implemented with a solenoid based Linac. The Linac consists of three styles of cryo-modules,containing focusing solenoids and varying number of SRF cavities for acceleration. Fringe fields of the solenoids and the focusing effects in the SRF cavities have significant impact on the transverse beam dynamics. Using an analytical formula,the effects of fringe fields and cavities are studied in MAD-X. The resulting betatron functions are compared with the results of beam dynamics simulations using OptiM code.
Muons, Inc, Batavia
ANL, Argonne
An extremely low emittance RF gun is being designed for the X-ray Free Electron Laser Oscillator (XFEL-O), which is now being proposed by ANL. An adjustable coupling factor for this gun is very desirable for providing operational flexibility. What is required is a fundamental RF power coupler (FPC), adjustable in situ, that can operate at 100 MHz and 200 kW CW. If rotational motion is used in the adjustable coupler, it is usually necessary to break the vacuum between the coupler and the RF cavity, thereby risking prolonged down-times and the introduction of contaminants into the vacuum system. We propose a novel system for adjusting the coupling coefficient of coaxial couplers to allow for individual control and adjustments to the RF fields under different beam loading scenarios. The RF coupler has no movable parts and relies on a ferrite tuner assembly, coax TEE, and double windows to provide a VSWR of better than 1.05:1 and a bandwidth of at least 8 MHz at 1.15:1. The ferrite tuner assembly on the stub end of the coax TEE uses an applied DC magnetic field to change the Qext and the RF coupling coefficient, β, between the RF input and the cavity.
GSI, Darmstadt
NSCL, East Lansing, Michigan
Electron Cyclotron Resonance Ion Sources (ECRIS) are increasingly used as ion source for different types of accelerator because of their high current densities for highly charged ions. To investigate the ion beam quality, normally delivered to the RFQ of the high charge state injector at GSI, we had the chance to install a viewing target close to the position of ion beam injection into the RFQ. The profile visible on the viewing target could be recorded through a regular glass window by a simple camera outside the vacuum. The RFQ itself has been removed for these measurements. We have found a highly structured ion beam distribution at that position. These structures, already caused by the hexapolar field within the ion source have already been observed directly behind the extraction. They are transported through the beam line without becoming homogeneous, which indicates a high degree of space charge compensation for that cw-beam. If the full beam line is mastered by the dipole, all charge states show similar ion beam distribution on the target for a given extraction voltage. This is also a hint, that the structures have been produced within the source already.
Osaka University, Osaka
KEK, Ibaraki
An intense muon beam is mandatory for the next-generation experiments to search for lepton flavor violating processes in the muon sector. The COMET experiment, J-PARC ·1021, aims to search for muon to electron conversion with an unprecedented sensitivity.. The muon beam is produced from pion decays in a strong magnetic field generated by superconducting solenoid coils. The large-bore superconducting coils enclose the pion-production target to capture pions with a large solid angle. The magnetic field is designed to have a peak of 5T at the target. To avoid severe radiation from the target, thick shielding is inserted in the warm bore of the pion capture solenoid magnet. The proton beam is injected through the gap between the pion capture solenoid and the subsequent transport solenoid magnets. For this purpose, the bore of the pion capture solenoid has to be larger than 1 m. This paper describes the design of the pion capture solenoid magnet for the COMET experiment.
Cockcroft Institute, Warrington, Cheshire
Lancaster University, Lancaster
The University of Liverpool, Liverpool
CLIC will need of order 10 to the 14 positrons per second to achieve its specified luminosity. For such a challenge, an undulator based scheme has been proposed as one of the options for the positron source. As CLIC may operate over a wide range of energy (from 0.5 TeV to 3 TeV), there is a large margin for us to push the performance of the whole system to be more efficient. We report on the undulator parameters and optimization of components of the source such as conversion target, AMD, solenoid and capture RF for different operational scenarios. In addition to maximizing the positron yield the polarization of the positron beam are also considered.
JAEA/TARRI, Gunma-ken
LBNL, Berkeley, California
The construction of the Extra Low ENergy Antiprotons (ELENA) upgrade to the Antiproton Decelerator (AD) ring has been proposed at CERN to produce a greatly increased current of low energy antiprotons for various experiments including, of course, anti-hydrogen studies. This upgrade involves the addition of a small storage ring and electrostatic beam lines. 5.3 MeV antiproton beams from AD are decelerated down to 100 keV in the compact ring and transported to each experiment apparatus. In this paper, we describe an electrostatic beam line from ELENA to ATRAP and magnetic shielding of the low-energy beam line against the ATRAP solenoid magnet. A possible design of this system is displayed.
INFN/LNL, Legnaro (PD)
Universita' degli Studi di Milano e INFN, Milano
In a Malmberg'Penning trap like ELTRAP an electron beam can be stored or propagated in a space charge dominated condition, due to the low acceleration voltage used; in particular we can test the longitudinal expansion of the electron bunch with several diagnostics, including Thomson scattering. Pulsed electron beams produced by an external photocathode source in the 1'10 keV energy range and with 4 ns length have been measured also by two electrostatic diagnostic systems. A proper software is needed to compensate for the capacitance of the pickup electrodes. Rf can be applied to the sectored electrode to produce a plasma source or to excite or to detect rotational modes; in particular the use of a new 8 sector electrode will allow up to m=3 modes.
Department of Energy Sciences, Tokyo Institute of Technology, Yokohama
BNL, Upton, Long Island, New York
RIKEN Nishina Center, Wako
In a laser ion source, a high power pulsed laser shot focused on a solid state target produces laser ablation plasma. This plasma has initial velocity towards the normal direction of the target and simultaneously expands three dimensionally. Since charge state distribution, velocity distribution and plasma temperature strongly depends on laser power density, power density is one of the important parameter to the angular distribution of plasma. Angular distribution of expanding plasma was measured by changing laser power density. Details of the experiment will be shown in the paper.
JINR, Dubna, Moscow Region
VNIIEF, Sarov (Nizhnii Gorod)
JINR/LHE, Moscow
The Electron String Ion Source (ESIS) developed at JINR is effectively used here during the last decade. The Tubular Electron String Ion Source (TESIS) has been put forward recently to obtain a 1-2 orders of magnitude increase in the ion output as compared with ESIS. The project is aimed at creating TESIS and studying the electron string in the tubular geometry. The new tubular source with a superconducting solenoid up to 5 T is under construction now. The method of the off axis TESIS ion extraction will be realized to get TESIS beam emittance comparable with ESIS emittance. It is expected that this new TESIS will meet all rigid conceptual and technological requirements and should provide an ion output approaching 10 mA of Ar16+ ions in the pulsed mode and about 10 μA of Ar16+ ions in the average current mode. Design, construction and test of separate TESIS systems are discussed in this report.
Kyushu University, Department of Applied Quantum Physics and Nuclear Engineering, Fukuoka
BNL, Upton, Long Island, New York
Department of Energy Sciences, Tokyo Institute of Technology, Yokohama
A laser ion source can provide high-current highly-charged ions with a simple structure. Previously we have demonstrated acceleration of >60 mA carbon and aluminum ion beams using a direct plasma injection scheme. However, it was not easy to control the ion pulse width. Especially to provide longer ion pulse, a plasma drift length which is the distance between laser target and extraction point, has to be extended and the plasma is diluted severely. We apply a solenoid field to prevent reduction of ion density at the extraction point. A solenoid field of a few hundred Gauss enhanced the ion density up to 40 times. We present these results, including details of the solenoidal field effects on the expanding laser plasma.
IAP, Frankfurt am Main
GSI, Darmstadt
The concept of laser acceleration of protons by Target Normal Sheath Acceleration TNSA from thin foils could be used to produce a high intensity proton bunch. This proton bunch could be injected into a linac at energies of ten to several tens MeV. A CH- structure is suggested as the linac structure because of its high gradient. The motivation for such a combination is to deliver single beam bunches with quite small emittance values of extremely high particle number - in the order of 10 billion protons per bunch. Optimum emittance values for linac injection are compared with available, laser generated beam parameters. Options and simulation tools for beam matching by pulsed solenoid and CH- structure using LASIN and LORASR codes are presented.
Rome University La Sapienza, Roma
INFN/LNF, Frascati (Roma)
ENEA C.R. Frascati, Frascati (Roma)
Protons generated by the irradiation of a thin metal foil by a high-intensity short-pulse laser have shown to posses interesting characteristics in terms of energy, emittance, current and pulse duration. They might therefore become in the next future a competitive source to conventional proton sources. Previous theoretical and numerical studies already demonstrated the possibility of an efficient coupling between laser-plasma acceleration of protons with traditional RF based beam-line accelerator techniques. This hybrid proton accelerator would therefore benefit from the good properties of the laser-based source and from the flexibility and know-how of beam handling as given from RF based accelerator structure. The proton beam parameters of the source have been obtained from published laser interaction experimental results and are given as input to the numerical study by conventional accelerator design tools. In this paper we discuss recent results in the optimization and design of the such hybrid schemes in the context of proton accelerators for medical treatments.
INFN/LNF, Frascati (Roma)
Bologna University, Bologna
Rome University La Sapienza, Roma
Electron beams produced by laser-plasma interaction are attracting the interest of the conventional accelerator community. In particular Laser-accelerated electrons are particularly interesting as source, considering their high initial energy and their strong beam current. Moreover, the advantages of using laser-plasma electron beam can be expressed in terms of size and cost of the global accelerating infrastructure. However, improvements are still necessary since, currently, the many laser-accelerated beams are characterized by a large energy spread and a high beam divergence that degrades quickly the electron beam properties and makes those sources not suitable as a replacement of conventional accelerators. In this paper, we report on the progress of the study related to capture, shape and transport of laser generated electrons by means of tracking codes. Our study has focused on laser-generated electrons obtained nowadays by conventional multi hundred TW laser systems and on numerical predictions. We analyze different lattice structures, working on the optimization of the capture and transport of laser-accelerated electrons. Results and open problems are shown and discussed.
DAE/VECC, Calcutta
A cylindrical lens is mainly used for focusing and transporting low energy beam. Some analytical forms of scalar potential have been formulated to evaluate electric and magnetic field and its derivatives on the central axis, which help in evaluation of potential and field in the region about the central axis. They are, subsequently, used to analytically find out the optical properties of a lens as well as in tracking of charged particles. It turns into a tool to design an electrostatic or a magnetic cylindrical lens. A section-technique has been developed to evaluate the optical cardinal points of a thick lens very accurately. Smooth profiles of the field and potential along the axis are divided into large number of small stepped profile. Each step represents a weak thin lens as change in radial movement is very small. The effect of the individual weak lenses is evaluated and combined by matrix multiplication method to get optical property of the thick lens. The obtained values are verified by exactly tracking the particles by solving the Lorentz equation of motion of charged particle in electric or magnetic field.
BINP SB RAS, Novosibirsk
Lattice correction based on orbit responses to dipole correctors and orbit correction based on orbit responses to field gradient variations in quads were successfully implemented on VEPP-2000 [*] for the flat-beam lattice. The round-beam lattice involves strong coupling of vertical and horizontal motions that require a full-coupling analysis in the orbit response technique. Programs used were modified to treat this task. Also, automation and speed enhancements were done that enable a routine use of this technique at VEPP-2000. New experimental results from VEPP-2000 are presented.
* Yu.M.Shatunov et al. Project of a New Electron-Positron Collider VEPP-2000, in: Proc. 7th European Particle Accelerator Conf. (EPAC 2000), Vienna, Austria, 439-441
Imperial College of Science and Technology, Department of Physics, London
JLAB, Newport News, Virginia
Within the Neutrino Factory Project the muon acceleration process involves a complex chain of accelerators including a (single-pass) linac, two recirculating linacs and an FFAG. The linac consists of RF cavities and iron shielded solenoids for transverse focusing and has been previously designed relying on idealized field models. However, to predict accurately the transport and acceleration of a high emittance 30 cm wide beam with 10 % energy spread requires detailed knowledge of fringe field distributions. This article presents results of the front-to-end tracking of the muon beam through numerically simulated realistic field distributions for the shielded solenoids and the RF fields. Real and phase space evolution of the beam has been studied along the linac and the results will be presented and discussed.
Fermilab, Batavia
CERN, Geneva
Polarized positron and electron beams are ideal for searching for new physics at the Compact Linear Collider (CLIC). In order to properly orient and preserve the polarization of the beam at the interaction point, the beam polarization must be manipulated by a spin rotator along the beam line. In this paper a spin rotator design for the CLIC is presented and its integration into the CLIC ring to main linac transport system is discussed.
PPPL, Princeton, New Jersey
This paper presents results of advanced numerical simulations demonstrating the feasibility of tight collective focusing of intense ion beams for the Neutralizing Drift Compression Experiment (NDCX-I). In the collective focusing scheme, a weak magnetic lens provides strong focusing of an intense ion beam carrying an equal amount of neutralizing electron background [S. Roberston, Phys. Rev. Lett. 48, 149 (1982)]. For instance, a solenoidal magnetic field of several hundred gauss can focus an intense neutralized ion beam within a short distance of several centimeters. The enhanced focusing is provided by a strong self-electric field, which is produced by the collective electron dynamics. The numerical simulations are performed with the LSP particle-in-cell (PIC) code, and the results of the simulations are found to be in good agreement with analytical predictions. Collective focusing limitations due to possible heating of the co-moving electrons during the transverse compression are also discussed.
KEK, Ibaraki
The KEKB and PEP-II B factories have achieved world record luminosities while doubling or tripling their original design luminosities. The demand now from the physics community is for Super B Factories with orders of magnitude higher luminosities than those achieved by the present generation of machines. This talk will discuss the next-generation B factories, which aim to push back the luminosity frontier in the search for physics beyond the Standard Model.
