Paper | Title | Other Keywords | Page |
---|---|---|---|
MOPHA040 | Beam Position Feedback System Supported by Karabo at European XFEL | controls, feedback, diagnostics, FEL | 281 |
|
|||
The XrayFeed device of Karabo [1, 2] is designed to provide spatial X-ray beam stability in terms of drift compensation utilizing different diagnostic components at the European XFEL (EuXFEL). Our feedback systems proved to be indispensable in cutting-edge pump-probe experiments at EuXFEL. The feedback mechanism is based on a closed loop PID control algorithm [3] to steer the beam position measured by a so-called diagnostic devices to the desired centered position via defined actuator adjusting the alignment of X-ray optical elements, in our case a flat X-ray mirror system. Several diagnostic devices and actuators can be selected according to the specific experimental area where a beam position feedback is needed. In this contribution, we analyze the improvement of pointing stability of X-rays using different diagnostic devices as an input source for our feedback system. Different types of photon diagnostic devices such as gas-based X-ray monitors [4], quadrant detectors based on avalanche photo diodes [5] and optical cameras imaging the X-ray footprint on scintillator screens have been evaluated in our pointing stability studies. | |||
![]() |
Poster MOPHA040 [0.963 MB] | ||
DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-MOPHA040 | ||
About • | paper received ※ 30 September 2019 paper accepted ※ 08 October 2019 issue date ※ 30 August 2020 | ||
Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
MOPHA069 | Automation of the Undulator Middle Plane Alignment Relative to the Electron Beam Position Using the K-Monochromator | undulator, electron, FEL, controls | 375 |
|
|||
The correct K value of an undulator is an important parameter to achieve lasing conditions at free electron lasers. The accuracy of the installation of the undulator in the tunnel is limited by the accuracy of the instruments used in surveying. Moreover, the position of the electron beam also varies depending on its alignment. Another source of misalignment is ground movement and the resulting change in the position of the tunnel. All this can lead to misalignment of the electron beam position relative to the center of the undulator gap up to several hundred microns. That, in turn, will lead to a deviation of the ΔK/K parameter several times higher than the tolerance requirement. An automated method of aligning the middle plane of the undulator, using a K-monochromator, was developed and used at European XFEL. Details of the method are described in this article. The results of the K value measurements are discussed. | |||
![]() |
Poster MOPHA069 [0.780 MB] | ||
DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-MOPHA069 | ||
About • | paper received ※ 30 September 2019 paper accepted ※ 10 October 2019 issue date ※ 30 August 2020 | ||
Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
TUBPL02 | Enabling Open Science for Photon and Neutron Sources | simulation, neutron, software, experiment | 694 |
|
|||
Funding: This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 823852 Photon and Neutron sources are producing more and more petabytes of scientific data each year. At the same time scientific publishing is evolving to make scientific data part of publications. The Photon and Neutron Open Science Cloud (PaNOSC*) project is a EU financed project to provide scientific data management for enabling Open Science. Data will be managed according to the FAIR principles. This means data will be curated and made available under an Open Data policy, findable, interoperable and reusable. This paper will describe how the European photon and neutron sources on the ESFRI** roadmap envision PaNOSC as part of the European Open Science Cloud***. The paper will address the issues of data policy, metadata, data curation, long term archiving and data sharing in the context of the latest developments in these areas. *https://panosc.eu **https://www.esfri.eu/ **https://ec.europa.eu/research/openscience/index.cfm?pg=open-science-cloud |
|||
![]() |
Slides TUBPL02 [14.942 MB] | ||
DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-TUBPL02 | ||
About • | paper received ※ 30 September 2019 paper accepted ※ 09 October 2019 issue date ※ 30 August 2020 | ||
Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
TUCPR01 | Developing a Toolkit for Analysis of LCLS Pump-Probe Data | experiment, detector, framework, interface | 795 |
|
|||
Funding: This work was performed in support of the LCLS project at SLAC supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-76SF00515 The data format and volume at LCLS requires significant computing expertise which not all user groups can provide. We will describe the path to and current status of a Python module that enables user groups to translate and reduce their data into a format that they can easily work with. The package is developed in Python and uses the standard LCLS data analysis framework. It encapsulates knowledge of the standard beam line components and adds convenient ways to reduce the data of larger detectors. Both an event-based (best for small event sizes) and a binned approach which is able to handle larger data as megapixel size detectors are simple to setup. MPI is used for fast turn around, enabling close to real time feedback necessary to make decisions of how to use the limited amount of beam time. Jupyter notebooks are provided to demonstrate some of the available options and can serve as a convenient quick start for fast turn around analysis. |
|||
![]() |
Slides TUCPR01 [4.088 MB] | ||
DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-TUCPR01 | ||
About • | paper received ※ 07 October 2019 paper accepted ※ 03 November 2019 issue date ※ 30 August 2020 | ||
Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
WEMPL009 | Tracking APS-U Production Components With the Component Database and eTraveler Applications | database, data-management, controls, software | 1026 |
|
|||
Funding: Argonne National Laboratory’s work was supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under contract DE-AC02-06CH11357 The installation of the APS-U has a short schedule of one year, making it imperative to be well prepared before the installation process begins. The Component Database (CDB) has been designed to help in documenting and tracking all the components for APS-U. Two new major domains, Machine Design domain and Measurement and Analysis Archive (MAARC) domain, have been added to CDB to further its ability in exhaustively documenting components. The Machine Design domain will help define the purpose of all the components in the APS-U design and the MAARC domain allows association of components with collected data. The CDB and a traveler application from FRIB have been integrated to help with documenting various processes performed, such as inspections and maintenance. Working groups have been formed to define appropriate work flow processes for receiving components, using the tools to document receiving inspection and QA requirements. The applications are under constant development to perform as expected by the working groups. Over some time, especially after production procurement began, the CDB has seen more and more usage in order to aid in preparation for the APS-U installation. |
|||
DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-WEMPL009 | ||
About • | paper received ※ 30 September 2019 paper accepted ※ 09 October 2019 issue date ※ 30 August 2020 | ||
Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
WEPHA057 | Building a Data Analysis as a Service Portal | software, data-analysis, site, feedback | 1228 |
|
|||
Funding: This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 730872 As more and more scientific data are stored at photon sources there is a growing need to provide services to access to view, reduce and analyze the data remotely. The Calipsoplus* project, in which all photon sources in Europe are involved in, has recognized this need and created a prototype portal for Data Analysis as a Service. This paper will present the technology choices, the architecture of the blueprint, the prototype services and the objectives of the production version planned in the medium term. The paper will cover the challenges of building a portal from scratch which covers the needs of multiple sites, each with their own data catalogue, local computing infrastructure and different workflows. User authentication and management are essential to creating a useful but sustainable service. *http://www.calipsoplus.eu/ |
|||
DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-WEPHA057 | ||
About • | paper received ※ 01 October 2019 paper accepted ※ 09 October 2019 issue date ※ 30 August 2020 | ||
Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
WEPHA063 | Precision Insertion Device Control and Simultaneous Monochromator Fly Scanning for NSLS-II | controls, insertion, insertion-device, EPICS | 1244 |
|
|||
Funding: U.S. Department of Energy DE-SC0012704 Beginning in January of 2019, 8 of the 10 In-Vacuum Undulators installed in the NSLS-II storage ring underwent in-house in-situ control system upgrades allowing for control of the magnetic gap during motion down to the 50 nm level with an in-position accuracy of nearly 5 nm. Direct linking of Insertion Devices and beamline monochromators is achieved via a fiber interface allowing precise, simultaneous, nonlinear motion of both devices and providing a fast hardware trigger for real-time accurate insertion device and monochromator fly scanning. This presentation will discuss use case scenarios at light source facilities and detail the precision achieved for simultaneous motion. Particular attention is given to the precision at which undulator energy harmonic peaks can be tracked and the variation of the peak flux in motion. |
|||
![]() |
Poster WEPHA063 [1.763 MB] | ||
DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-WEPHA063 | ||
About • | paper received ※ 30 September 2019 paper accepted ※ 10 October 2019 issue date ※ 30 August 2020 | ||
Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||