Keyword: laser
Paper Title Other Keywords Page
MOPHA059 Ultra-High Precision Timing System for the CEA-Laser Megajoule controls, timing, ISOL, shielding 347
 
  • S. Hocquet, N. Bazoge, Ph. Hours, D. Monnier-Bourdin
    Greenfield Technology, Massy, France
  • T. Falgon, T. Somerlinck
    CEA, LE BARP cedex, France
 
  High power laser such as the Laser MegaJoule (LMJ) or National Ignition Facility (NIF) requires different types of trigger precision to synchronize all the laser beams, plasma diagnostics and generate fiducials. Greenfield Technology, which designs and produces picosecond delay generator and timing system for about 20 years, has been hired by CEA to develop new products to meet the LMJ requirements. About 2000 triggers are about to be set to control and synchronize all of the 176 laser beams on the target with a precision better than 40 ps RMS. Among these triggers, Greenfield Technology’s GFT1012 is a 4-channels delay generator challenging ultra-high performances: an ultra-low jitter between 2 slaves below 4 ps RMS and a peak-to-peak wander over 1 week lower than 6 ps due to a thermal control of the most sensitive part (the thermal drift is below 1 ps/°C) and specific developments for clock management and restitution. On going investigation should bring the jitter close to 2 ps RMS between 2 slaves.  
poster icon Poster MOPHA059 [0.488 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-MOPHA059  
About • paper received ※ 30 September 2019       paper accepted ※ 09 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
MOPHA062 The Personnel Safety System of ELI-ALPS PLC, controls, interlocks, radiation 351
 
  • F. Horvath, L.J. Fülöp, Sz. Horváth, Z. Héjja, T. Kecskés, I. Kiss, V. Kurusa, G. Kávai, K. Untener
    ELI-ALPS, Szeged, Hungary
 
  Funding: ELI-ALPS is supported by the European Union and cofinanced by the European Regional Development Fund (GOP-1.1.1-12/B-2012-000, GINOP-2.3.6-15-2015-00001)
ELI-ALPS will be the first large-scale attosecond facility accessible to the international scientific community and its user groups. The facility-wide Personnel Safety System (PSS) has been successfully developed and commissioned for the majority of the laboratories. The system has three major goals. First, it provides safe and automatic sensing and interlocking engineering measures as well as monitoring and controlling interfaces for all laboratories in Building A: emergency stop buttons, interlock and enabling signals, door and roller blind sensors, and entrance control. Second, it integrates and monitors the research technology equipment delivered by external parties as black-box systems (all laser systems, and some others). Third, it includes the PSS subsystems of research technology equipment developed on site by in-house and external experts (some of the secondary sources). The gradual development of the system is based on the relevant standards and best practices of functional safety as well as on an iterative and systematic lifecycle incorporating several internal and external reviews. The system is implemented with an easily maintainable network of safety PLCs.
 
poster icon Poster MOPHA062 [1.323 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-MOPHA062  
About • paper received ※ 30 September 2019       paper accepted ※ 08 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
MOPHA086 The Design of Experimental Performance Analysis and Visualization System experiment, data-management, data-analysis, database 409
 
  • J. Luo, L. Li, Z. Ni, X. Zhou
    CAEP, Sichuan, People’s Republic of China
  • Y. Gao
    Stony Brook University, Stony Brook, New York, USA
 
  The analysis of experimental performance is an essential task to any experiment. With the increasing demand on experimental data mining and utilization. methods of experimental data analysis abound, including visualization, multi-dimensional performance evaluation, experimental process modeling, performance prediction, to name but a few. We design and develop an experimental performance analysis and visualization system, consisting of data source configuration component, algorithm management component, and data visualization component. It provides us feasibilities such as experimental data extraction and transformation, algorithm flexible configuration and validation, and multi-views presentation of experimental performance. It will bring great convenience and improvement for the analysis and verification of experimental performance.  
poster icon Poster MOPHA086 [0.232 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-MOPHA086  
About • paper received ※ 30 September 2019       paper accepted ※ 10 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
TUBPR05 LEReC Timing Synchronization with RHIC Beam timing, electron, software, controls 746
 
  • P.K. Kankiya, M.R. Costanzo, J.P. Jamilkowski
    BNL, Upton, New York, USA
 
  Funding: Work supported by Brookhaven Science Associates, LLC under Contract No. DE-SC0012704 with the U.S. Department of Energy
In RHIC low energy bunched beam cooling experiment, LEReC, a 704 MHz fiber laser is modulated such that when striking a photocathode, it produces corresponding electron bunches which are accelerated and transported to overlap an ion beam bunched at 9 MHz RF frequency The need for precise timing is handled well by the existing infrastructure. A layer of software application called the timing manager has been created to track the LEReC beam concerning the RHIC beam and allow instruments to be fired in real-time units instead of bunch timing or RHIC turns. The manager also automates set-tings of different modes based on the RF frequency and maintains the timing of instrumentation with a beam. A detailed description of the bunch structure and scheme of synchronizing the RF and laser pulses will be discussed in the paper.
 
slides icon Slides TUBPR05 [4.693 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-TUBPR05  
About • paper received ※ 04 October 2019       paper accepted ※ 09 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
TUBPR06 Laser Megajoule Timing System timing, diagnostics, target, experiment 749
 
  • T. Somerlinck, T. Falgon
    CEA, LE BARP cedex, France
  • N. Bazoge, S. Hocquet, D. Monnier-Bourdin
    Greenfield Technology, Massy, France
 
  The aim of the Laser Megajoule facility (LMJ) is to deliver more than 1 MJ of laser energy to targets for high energy density physics experiments. In association with Greenfield Technology, we developed a specific timing system to synchronize the 176 laser beams on the target with a precision better than 40 ps rms and to trigger and mark plasma diagnostics. The final architecture, settled and used since three years, is based on a master oscillator that sends a clock with serial data through a fiber-optic network, allowing to synchronize more than 500 delay generators spread over the large LMJ facility. The settings of each laser beam and the various experiments require different sampling rates (multi to single shot) and 16 groups for coactivity. Three kinds of delay generators, electrical and optical, are designed for standard precision (<150 ps jitter) and the third is designed for high precision. Each output deliver trigger or fiducial signals with jitter down to 5 ps and peak-to-peak wander less than 10 ps over a week. Test performance of this LMJ timing system is in progress all over the LMJ facility. Besides it will be installed on the petawatt laser (PETAL) this year.  
slides icon Slides TUBPR06 [58.283 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-TUBPR06  
About • paper received ※ 30 September 2019       paper accepted ※ 10 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
TUCPL05 ESRF-Double Crystal Monochromator Prototype - Control Concept controls, SRF, real-time, feedback 776
 
  • M. Brendike, R. Baker, G. Berruyer, L. Ducotté, H. Gonzalez, C. Guilloud, M. Perez
    ESRF, Grenoble, France
 
  The ESRF-Double Crystal Monochromator (ESRF-DCM) has been designed and developed in-house to enable spectroscopy beamlines to exploit the full potential of the ESRF-EBS upgrade. To reach concomitant beam positioning accuracy and beam stability at nanometer scale with a reliable, robust and simple control system, a double cascaded control architecture is implemented. The cascade is comprised of three modes: classic open loop actuation, an optimized open loop mode with error mapping, and closed loop real-time actuation. Speedgoat hardware, programmable from MATLAB/SIMULINK and running at 10 kHz loop frequency is used for the real-time mode. From the EBS startup 2020, the ESRF plans to deploy BLISS – the new BeamLine Instrumentation Support Software control system – for running experiments. An interface between Speedgoat hardware and BLISS has therefore been developed. The DCM and its control architecture have been tested in laboratory conditions. An overview of the concept, implementation and results of the cascaded control architecture and its three modes will be presented  
slides icon Slides TUCPL05 [5.113 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-TUCPL05  
About • paper received ※ 30 September 2019       paper accepted ※ 09 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
WEBPP01 Control System Development and Integration at ELI-ALPS controls, vacuum, interface, software 880
 
  • L. Schrettner, B. Bagó, B. Erdohelyi, L.J. Fülöp, F. Horvath, Sz. Horváth, Z. Héjja, V. Kurusa, G. Kávai
    ELI-ALPS, Szeged, Hungary
 
  Funding: ELI-ALPS is supported by the European Union and cofinanced by the European Regional Development Fund (GOP-1.1.1-12/B-2012-000, GINOP-2.3.6-15-2015-00001)
ELI-ALPS will be the first large-scale attosecond facility accessible to the international scientific community and its user groups. Control system development has three major directions: vacuum control systems, optical control systems, as well as the integrated control, monitoring and data acquisition systems. The development of the systems has asked for different levels of integration. In certain cases low-level devices are integrated (e.g. vacuum valves), while in other cases complete systems are integrated (e.g. the Tango interface of a laser system). This heterogeneous environment is managed through the elaboration of a common and general architecture. Most of the hardware elements are connected to PLCs (direct control level), which are responsible for the low-level operation of devices, including machine protection functions, and data transfer to the supervisory control level (CLIs, GUIs). Certain hardware elements are connected to the supervisory layer (cameras), as well as the Tango interface of the laser systems. This layer handles also data acquisition with a special focus on the metadata catalogue.
 
slides icon Slides WEBPP01 [2.684 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-WEBPP01  
About • paper received ※ 01 October 2019       paper accepted ※ 09 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
WEBPP03 The Laser Megajoule Facility: Front End’s Control System controls, software, interface, operation 891
 
  • J. Langot, C. Baret, P. Fourtillan, J.F. Gleyze, D. Hamon, D. Lebeaux, A. Perrin
    CEA, LE BARP cedex, France
 
  The Laser Megajoule (LMJ) is a 176-beam laser facility, located at the CEA CESTA Laboratory near Bordeaux (France). It is designed to deliver about 1.5 MJ of energy to targets, for high energy density physics experiments, including fusion experiments. Six 8-beams bundles are currently operational. The Front-End is the LMJ subsystem built to deliver the laser pulse which will be amplified into the bundles. It consists of 4 laser seeders, producing the laser pulses with the expected specificities and 88 Pre-Amplifier Modules (PAM). In this paper, we introduce the architecture of the Front-End’s control system which coordinate the operations of the laser seeders and the PAMs’s control systems. We will discuss the ability of the laser seeders and their control systems to inject the 88 PAMs almost independently. Then we will deal with the functions that enable the expected laser performances in terms of energy, spatial and temporal shapes. Finally, the technics used to validate and optimize the operation of the software involved in the Front-End’s equipment performance will be detailed.  
slides icon Slides WEBPP03 [58.495 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-WEBPP03  
About • paper received ※ 26 September 2019       paper accepted ※ 10 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
WEPHA021 Free-Electron Laser Optimization with Reinforcement Learning FEL, electron, controls, free-electron-laser 1122
 
  • N. Bruchon, G. Fenu, F.A. Pellegrino, E. Salvato
    University of Trieste, Trieste, Italy
  • G. Gaio, M. Lonza
    Elettra-Sincrotrone Trieste S.C.p.A., Basovizza, Italy
 
  Reinforcement Learning (RL) is one of the most promising techniques in Machine Learning because of its modest computational requirements with respect to other algorithms. RL uses an agent that takes actions within its environment to maximize a reward related to the goal it is designed to achieve. We have recently used RL as a model-free approach to improve the performance of the FERMI Free Electron Laser. A number of machine parameters are adjusted to find the optimum FEL output in terms of intensity and spectral quality. In particular we focus on the problem of the alignment of the seed laser with the electron beam, initially using a simplified model and then applying the developed algorithm on the real machine. This paper reports the results obtained and discusses pros and cons of this approach with plans for future applications.  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-WEPHA021  
About • paper received ※ 30 September 2019       paper accepted ※ 09 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
WEPHA052 Engineering Support Activities at ELI-ALPS Through a Systems Engineering Perspective controls, operation, vacuum, software 1219
 
  • L.J. Fülöp, F. Horvath, I. Kiss, A. Makai, L. Schrettner
    ELI-ALPS, Szeged, Hungary
 
  Funding: ELI-ALPS is supported by the European Union and cofinanced by the European Regional Development Fund (GOP-1.1.1-12/B-2012-000, GINOP-2.3.6-15-2015-00001).
ELI-ALPS will be the first large-scale attosecond facility accessible to the international scientific community and its user groups. The core business of ELI-ALPS is to generate attosecond pulses and provide these to the prospective users. In order to reach this ultimate goal, one key support area, the engineering development of complex systems as well as the engineering custom design service, has been systematically elaborated based on the standards, recent results, trends and best practices of systems engineering. It covers the boundaries towards all related support areas, from building operation and maintenance, to the custom manufacturing provided by the workshops, with the intention to make the model as well as the daily work as comprehensive and consistent as possible. Different tools have been evaluated and applied through the years, however, a key lessons learned is that some of the most important tools are teamwork, personal communication and constructive conflicts.
 
poster icon Poster WEPHA052 [1.119 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-WEPHA052  
About • paper received ※ 01 October 2019       paper accepted ※ 10 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
THCPL04 SCIBORG: Analyzing and Monitoring LMJ Facility Health and Performance Indicators software, controls, database, monitoring 1597
 
  • J-P. Airiau, V. Denis, P. Fourtillan, C. Lacombe, S. Vermersch
    CEA, LE BARP cedex, France
 
  The Laser MegaJoule (LMJ) is a 176-beam laser facility, located at the CEA CESTA laboratory near Bordeaux (France). It is designed to deliver about 1.4 MJ of energy to targets, for high energy density physics experiments, including fusion experiments. It operates, since June 2018, 5 of the 22 bundles expected in the final configuration. Monitoring system health and performance of such a facility is essential to maintain high operational availability. SCIBORG is the first step of a larger software that will collect in one tool all the facility parameters. Nowadays SCIBORG imports experiment setup and results, alignment and PAM* control command parameters. It is designed to perform data analysis (temporal/crossed) and implements monitoring features (dashboard). This paper gives a first user feedback and the milestones for the full spectrum system.
*PreAmplifier Module
 
slides icon Slides THCPL04 [4.882 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-THCPL04  
About • paper received ※ 01 October 2019       paper accepted ※ 08 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
FRAPP01 The Laser MegaJoule Facility: Command Control System Status Report target, controls, diagnostics, MMI 1652
 
  • H. Durandeau, R. Clot, P. Gontard, S. Tranquille-Marques, Y. Tranquille-Marques
    CEA, LE BARP cedex, France
 
  The Laser MegaJoule (LMJ) is a 176-beam laser facility, located at the CEA CESTA Laboratory near Bordeaux (France). It is designed to deliver about 1.4 MJ of energy on a target, for high energy density physics experiments, including fusion experiments. The first bundle of 8-beams bundle was commissioned in October 2014. Today five bundles are in operation. In this paper, we focus on two specific evolutions of the command control: the Target Chamber Diagnostic Module (TCDM) which allows the measurement of vacuum windows damages (an automatic sequence activates the TCDM that can be operated at night without any operator) and new Target Diagnostics integration. We also present a cybersecurity network analysis system based on Sentryo Probes and how we manage maintenance laptops in the facility.  
slides icon Slides FRAPP01 [20.352 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-FRAPP01  
About • paper received ※ 27 September 2019       paper accepted ※ 20 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
FRAPP06 Status of the Control System for the Energy Recovery Linac BERLinPro at HZB controls, EPICS, operation, gun 1669
 
  • T. Birke, P. Echevarria, D. Eichel, R. Fleischhauer, J.G. Hwang, G. Klemz, R. Müller, C. Schröder, E. Suljoti, A. Ushakov
    HZB, Berlin, Germany
  • K. Laihem
    RWTH, Aachen, Germany
 
  BERLinPro is an energy recovery linac (ERL) demonstrator project built at HZB. It features CW SRF technology for the low emittance, high brightness gun, the booster module and the recovery linac. Construction and civil engineering are mostly completed. Synchronized with the device integration the EPICS based control system is being set-up for testing, commissioning and finally operation. In the warm part of the accelerator technology that is already operational at BESSY and MLS (e.g. CAN-bus and PLC/OPCUA) is used. New implementations like the machine protection system and novel major subsystems (e.g. LLRF, Cryo-Controls, photo cathode laser) need to be integrated. The first RF transmitters have been tested and commissioned. At the time of this conference the first segment of the accelerator is scheduled to become online. For commissioning and operation of the facility the standard set of EPICS tools form the back-bone. A set of generic Python applications already developed at BESSY/MLS will be adapted to the specifics of BERLinPro. Scope and current project status are described in this paper.  
slides icon Slides FRAPP06 [10.806 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-ICALEPCS2019-FRAPP06  
About • paper received ※ 29 September 2019       paper accepted ※ 09 October 2019       issue date ※ 30 August 2020  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)