MEDSI2016 - List of Authors (Chang, S.H.)

Paper	Title	Page
MOPE05	Mechanical Design of Secondary Source Slits for Hard X-ray Beamlines at Taiwan Photon Source	12
	H.Y. Yan, C.H. Chang, S.H. Chang, C.Y. Chen, C.Y. Huang, J.M. Lin, D.G. Liu, D.-J. Wang NSRRC, Hsinchu, Taiwan
	The secondary source slits have been developed for specific hard X-ray beam-lines at Taiwan Photon Source. Especially for Coherent X-ray Scattering and X-ray Nanoprobe beam-lines, severe specifications of the slits are more necessary to define proper beam sizes in horizontal and vertical directions at sample. The opening size of each pair of slits assembled orthogonally is usually needed to range within several microns, so the UHV-compatible piezo-driven stages with closed-loop system were adopted for the purposes of fine adjustment, precise positional accuracy and repeatability. To reduce X-ray scattering effect, the rectangular single-crystal film was bonded on the edge of the slit blade. The machined rotary weak-link structure and piezo-driven actuators were used to slightly adjust parallelism of each pair of the blades with the method of single-slit diffraction. To enhance structural and thermal stability, the granite plinths with specified shape were designed and the precise temperature controlling system will be set up recently. The overall design, mechanical specifications and procedure of testing for secondary source slits will be introduced in this paper.
	Poster MOPE05 [0.795 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-MEDSI2016-MOPE05
About •	paper received ※ 09 September 2016 paper accepted ※ 14 September 2016 issue date ※ 22 June 2017
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPE24	The Precision Adjustment Holder for Montel Mirrors	57
	B.Y. Chen, S.H. Chang, H.Y. Chen, C.Y. Lee, B.H. Lin, M.T. Tang, S.C. Tseng, J.X. Wu, G.C. Yin NSRRC, Hsinchu, Taiwan M. Hong National Taiwan University, Taipei, Taiwan J.R. Kwo NTHU, Hsinchu, Taiwan
	The focusing of X-ray nanoprobe at TPS relay upon the special designed Montel mirrors and its adjustment holder. The holder includes two major parts: (1) fundamental-position alignment part and (2) relative-position adjustment part. The fundamental-position alignment part has the ability to adjust the two mirrors together in 6 DOF., such as X, Y, Z, pitch, roll, and yaw. These translation stages have several-tens mm travel range and nm resolution, while the rotational stages have 40 mrad azimuthal angular range and 0.1~0.01 µrad resolution. The relative-position adjustment part can further adjust the two mirrors to minimize the focal spot. During the pre-alignment process, one of the mirrors can be manual adjusted by micrometer heads in three translation directions with several mm travel range and micro-meters resolution. These micrometer heads also provide this mirror three rotational degree of freedoms with sub-mrad resolution. For the further alignment in vacuum, the additional four piezo-motor actuators can precisely adjust the other Montel mirror in the Y and Z direction with several nm resolution, and its pitch and roll with 1 urad and 0.05 urad resolution, respectively.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-MEDSI2016-MOPE24
About •	paper received ※ 14 September 2016 paper accepted ※ 19 September 2016 issue date ※ 22 June 2017
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPE12	Developing White Beam Components of TPS Beamline 24A	183
	M.H. Lee, C.Y. Chang, C.H. Chang, S.H. Chang, C. Chen, C.C. Chiu, L. Huang, L. Lai, L. Lee, D.G. Liu, Y. Su, H.Y. Yan NSRRC, Hsinchu, Taiwan
	The TPS 24A, Soft X-ray Tomography (SXT) beamline, is one of the beamlines in the second construction phase at the Taiwan Photon Source (TPS). This bending magnet (BM) beamline has high flux in the range between 260 eV and 2600 eV. It is designed for transmission full-field imaging of frozen-hydrated biological samples. At the exit slit, the beam flux optimized in 520 eV is 282 billion photons/second with resolving power 2000, the beam size is 0.05 mm × 0.06 mm (V × H, FWHM) and the beam divergence is 1.73 mrad × 1.57 mrad (V × H, FWHM). By contributions of the generic beamline components project in recent years, modular mechanisms would be used in this beamline such as mask, X-ray beam position monitor (XBPM), photon absorber (PAB), and screens. However, these beamline components were designed for ID beamlines, so they should be redesigned for BM beamlines. This paper generally introduce these beamline components decided and redesigned for the TPS 24A. They will play important roles at the BM beam-lines in the future.
	Poster TUPE12 [1.355 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-MEDSI2016-TUPE12
About •	paper received ※ 09 September 2016 paper accepted ※ 22 September 2016 issue date ※ 22 June 2017
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Mechanical Design of Secondary Source Slits for Hard X-ray Beamlines at Taiwan Photon Source

12

H.Y. Yan, C.H. Chang, S.H. Chang, C.Y. Chen, C.Y. Huang, J.M. Lin, D.G. Liu, D.-J. Wang
NSRRC, Hsinchu, Taiwan

The secondary source slits have been developed for specific hard X-ray beam-lines at Taiwan Photon Source. Especially for Coherent X-ray Scattering and X-ray Nanoprobe beam-lines, severe specifications of the slits are more necessary to define proper beam sizes in horizontal and vertical directions at sample. The opening size of each pair of slits assembled orthogonally is usually needed to range within several microns, so the UHV-compatible piezo-driven stages with closed-loop system were adopted for the purposes of fine adjustment, precise positional accuracy and repeatability. To reduce X-ray scattering effect, the rectangular single-crystal film was bonded on the edge of the slit blade. The machined rotary weak-link structure and piezo-driven actuators were used to slightly adjust parallelism of each pair of the blades with the method of single-slit diffraction. To enhance structural and thermal stability, the granite plinths with specified shape were designed and the precise temperature controlling system will be set up recently. The overall design, mechanical specifications and procedure of testing for secondary source slits will be introduced in this paper.

Poster MOPE05 [0.795 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-MEDSI2016-MOPE05

About •

paper received ※ 09 September 2016 paper accepted ※ 14 September 2016 issue date ※ 22 June 2017

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPE24

The Precision Adjustment Holder for Montel Mirrors

57

B.Y. Chen, S.H. Chang, H.Y. Chen, C.Y. Lee, B.H. Lin, M.T. Tang, S.C. Tseng, J.X. Wu, G.C. Yin
NSRRC, Hsinchu, Taiwan
M. Hong
National Taiwan University, Taipei, Taiwan
J.R. Kwo
NTHU, Hsinchu, Taiwan

The focusing of X-ray nanoprobe at TPS relay upon the special designed Montel mirrors and its adjustment holder. The holder includes two major parts: (1) fundamental-position alignment part and (2) relative-position adjustment part. The fundamental-position alignment part has the ability to adjust the two mirrors together in 6 DOF., such as X, Y, Z, pitch, roll, and yaw. These translation stages have several-tens mm travel range and nm resolution, while the rotational stages have 40 mrad azimuthal angular range and 0.1~0.01 µrad resolution. The relative-position adjustment part can further adjust the two mirrors to minimize the focal spot. During the pre-alignment process, one of the mirrors can be manual adjusted by micrometer heads in three translation directions with several mm travel range and micro-meters resolution. These micrometer heads also provide this mirror three rotational degree of freedoms with sub-mrad resolution. For the further alignment in vacuum, the additional four piezo-motor actuators can precisely adjust the other Montel mirror in the Y and Z direction with several nm resolution, and its pitch and roll with 1 urad and 0.05 urad resolution, respectively.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-MEDSI2016-MOPE24

About •

paper received ※ 14 September 2016 paper accepted ※ 19 September 2016 issue date ※ 22 June 2017

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPE12

Developing White Beam Components of TPS Beamline 24A

183

M.H. Lee, C.Y. Chang, C.H. Chang, S.H. Chang, C. Chen, C.C. Chiu, L. Huang, L. Lai, L. Lee, D.G. Liu, Y. Su, H.Y. Yan
NSRRC, Hsinchu, Taiwan

The TPS 24A, Soft X-ray Tomography (SXT) beamline, is one of the beamlines in the second construction phase at the Taiwan Photon Source (TPS). This bending magnet (BM) beamline has high flux in the range between 260 eV and 2600 eV. It is designed for transmission full-field imaging of frozen-hydrated biological samples. At the exit slit, the beam flux optimized in 520 eV is 282 billion photons/second with resolving power 2000, the beam size is 0.05 mm × 0.06 mm (V × H, FWHM) and the beam divergence is 1.73 mrad × 1.57 mrad (V × H, FWHM). By contributions of the generic beamline components project in recent years, modular mechanisms would be used in this beamline such as mask, X-ray beam position monitor (XBPM), photon absorber (PAB), and screens. However, these beamline components were designed for ID beamlines, so they should be redesigned for BM beamlines. This paper generally introduce these beamline components decided and redesigned for the TPS 24A. They will play important roles at the BM beam-lines in the future.

Poster TUPE12 [1.355 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-MEDSI2016-TUPE12

About •

paper received ※ 09 September 2016 paper accepted ※ 22 September 2016 issue date ※ 22 June 2017

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)