Paper | Title | Other Keywords | Page |
---|---|---|---|
MO3RAI03 | Construction and Commissioning of BEPCII | luminosity, linac, injection, cavity | 33 |
|
|||
BEPCII is major upgrades of BEPC (Beijing Electron-Positron Collider). It is a double ring e±e collider as well as a synchrotron radiation (SR) source with its outer ring, or SR ring. As a collider, BEPCII operates in the beam energy region of 1-2.1 GeV with design luminosity of 1*1033cm-2s-1 at 1.89 GeV. As a light source, the SR ring operates at 2.5 GeV and 250 mA. Construction of the project started in the beginning of 2004. Installation of the storage ring components completed in October 2007. The BESIII detector was moved to the Interaction Region (IR) on May 6, 2008. In accordance to the progress of construction, the beam commissioning of BEPCII is carried out in 3 phases: Phase 1, with conventional magnets instead of the superconducting insertion magnets (SIM’s)n in the IR; Phase 2, with SIM’s in the IR; Phase 3, joint commissioning with the detector. The maximum luminosity reached to 2.3*1032cm-2s-1. This paper summarizes progress of the construction and commissioning in 3 phases, while focusing on the third phase. * On behalf of the BEPCII Team |
|||
|
|||
MO4RAI01 | Experience with DAΦNE Upgrade Including Crab Waist | luminosity, sextupole, injection, feedback | 80 |
|
|||
In 2007 DAΦNE was upgraded to operate in a regime of large Piwinski angle, with a novel IR optics, reduced vertical beta at the interaction point, and additional sextupoles providing for crab waist collisions. The specific luminosity was boosted by more than a factor of four, and the peak luminosity was more than doubled with respect to the maximum value obtained with the original collider configuration. The DAΦNE commissioning as well as the first experience with large Piwinski angle and crab waist collisions scheme will be reported. |
|||
|
|||
MO6PFP021 | Magnetic Field Measurement System for CYCHU-10 | controls, cyclotron, alignment, ion-source | 181 |
|
|||
Funding: National Natural Science Foundation of China (No. 10435030) A 10MeV H- compact cyclotron (CYCHU-10) is under construction in Huazhong University of Science and Technology (HUST). This paper presents a magnetic field measurement system for measuring the cyclotron magnet. A Hall probe and a granite x-y stage are adopted in the project. The Cartesian mapping will replace traditional polar system. The motion control and data acquisition system for the magnetic field measurement consists of a Teslameter and Hall probe, servomotors, a motion control card, optical linear encoder systems and an industrial PC. The magnetic field will be automatically scanned by this apparatus, and a flying mode will be the main running mode to reduce measure time. |
|||
MO6PFP081 | Magnetic Field Measurement System for Superconducting Undulators | undulator, laser, controls, linear-collider | 321 |
|
|||
Funding: Work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357. The baseline configuration of the proposed International Linear Collider includes superconducting helical undulators as a scheme to produce positrons. This paper presents a conceptual design of the magnetic field measurement system for helical undulators with the undulator axis in a horizontal direction at liquid helium temperature. The system consists of a cryomodule and a linear stage unit with a travel length of approximately 3.5 m. The linear stage unit provides the motion control for the Hall probe housing, which is connected to a small-diameter carbon fiber rod inside bellows-flange connections. Stainless steel bellows are at the same vacuum pressure as the cold mass in the cryomodule. A linear encoder is used for motion control of the stage, but precise position measurement of the Hall probe relies on the laser interferometer system. |
|||
MO6RFP015 | Gas Desorption from TiN-Coated Copper Beam Duct | electron, vacuum, cathode, proton | 381 |
|
|||
The titanium nitride (TiN) coating inside a beam duct has been recently attracting attention as a measure to mitigate the electron cloud effect in positron/proton rings. Here studied is the gas desorption from the TiN-coated copper beam duct, which will be adopted in the upgrade of KEK B-factory (KEKB). In the experiment, the pressure in a TiN-coated duct was measured and compared with that in a non-coated one. The TiN film (200 nm thick) was coated by DC magnetron sputtering at KEK. After an air exposure for the previously-determined period, the duct was evacuated by a turbo-molecular pump (300 l/s). At 50 hours after evacuation, the pressure was about 4 times larger than that for the case of the non-coated one. The residual gas was mainly water. In order to fine the minimum baking temperature to decrease the gas desorption from the TiN coating, the pressures were measured after the baking by changing the temperatures in the practical range, from 50 to 150 degrees. The pressure after the baking at 80 degrees was finally found to be comparable to that for the non-coated one. This paper describes these results in detail including the measurements of gas desorption rates. |
|||
MO6RFP061 | Positron Source Target Survivability Studies | target, undulator, radiation, simulation | 503 |
|
|||
Energy deposition in the conversion targets of positron sources for future linear colliders will lead to thermal shock waves which could limit the targets' lifetimes. For the International Linear Collider baseline source, we have studied the energy deposition in a target taking the higher harmonics of the undulator radiation fully into account and applying hydrodynamical models for the resulting heat flow to determine the thermal stress in the target and to assess its survivability. |
|||
MO6RFP064 | Stacking Simulations for Compton Positron Sources of Future Linear Colliders | injection, damping, septum, emittance | 512 |
|
|||
The Compton positron source of a future linear collider must obtain the target bunch population by accumulating a large number of positron packets, arriving either in a number of bursts from a “Compton ring”, with intermediate damping of the scattering electron beam, or quasi-continually from a “Compton energy recovery linac”. We present simulation results for the longitudinal stacking of Compton positrons in the ILC damping ring and the CLIC pre-damping ring, reporting parameter optimization, stacking efficiency, possible further improvements, and outstanding questions. |
|||
MO6RFP066 | Operational Performance of Positron Production from Tungsten Single-Crystal Target at the KEKB Injector Linac | target, electron, solenoid, linac | 518 |
|
|||
The first operation of the positron production with a tungsten single-crystal target has been performed at the positron source of the KEKB injector linac for the KEK B-factory (KEKB) from September 2006 to June 2007 (~10 months). Previously we carried out the systematic studies on the positron-production efficiencies with tungsten crystals having various thickness using 4- and 8-GeV electron beams at the test beam line during the term of 2000-2005. Finally, we optimized the thickness of the tungsten crystal at 4 GeV and developed both the target fabrication technique and the crystal-axis alignment technique in 2006. After the systematic studies, we installed a tungsten crystal target at the KEKB positron source without any significant modifications for the positron source. The data on the positron production, especially, the positron-production efficiencies and stabilities in terms of the primary electron and positron beams, were obtained during the nominal KEKB operation in this term. We summarize the long-term operational performance on the positron production with the tungsten crystal target at the KEKB injector linac in this report. |
|||
MO6RFP068 | ERL Parameters for Compton Polarized Positron Sources | laser, electron, storage-ring, target | 524 |
|
|||
One of the main challenges for the future linear colliders projects (ILC and CLIC) is to design an efficient positron source taking into account the constraints imposed by the target heating. At present, different schemes have been analysed to produce high energy gammas and to convert them in an amorphous target. One of them considers the possibility to boost the energy of the backscattered photons of a laser pulse by Compton effect. This method is very attractive since the source is independent from the main Linac and since the photon helicity is conserved in Compton scattering and subsequently transferred to the produced pairs. This allows the physics experiments disposing of both positron and electron polarised sources. Different schemes have been proposed to provide the electron beam for the Compton collisions. taking into account the constraint imposed by the low value of the Thomson cross section. One of the explored possibilities is to design an ERL with relatively low repetition frequency, high charge per pulse and then to stack the produced positrons in an accumulation ring. Different considerations on this scheme will be illustrated and the main constraints discussed. |
|||
MO6RFP092 | Undulator-Based Positron Source for CLIC | undulator, electron, photon, target | 581 |
|
|||
A model has been created in Geant4 to simulate the key elements of an undulator-based positron source for CLIC: the goal is to consider such a source as an alternative to the present baseline concept. The parameters of the undulator and capture device have been optimized for a range of operating scenarios. In each case we have calculated the rate of positron production, positron polarization and capture efficiency. We discuss the strengths and weaknesses of the undulator scheme in CLIC. |
|||
MO6RFP093 | High Power Photon Collimators for the ILC | photon, polarization, target, undulator | 584 |
|
|||
An undulator-based source has been chosen as a part of the baseline configuration for the International Linear Collider (ILC) to generate an intense beam of polarised positrons. A photon collimator placed between the undulator and the target can be used to adjust the size, intensity and polarisation of the photon beam impacting the target, and can also protect the target station and limit the activation of downstream components. In this paper, we calculate quantities such as the energy deposition, temperature change, activation and dose rate for different designs of the photon collimator, and consider the advantages and disadvantages for each case. |
|||
TU5RFP001 | A Study of Lattice Structure and Insertion Devices at the Positron Ring of the TAC Project | lattice, radiation, storage-ring, brilliance | 1081 |
|
|||
The Turkish Accelerator Complex (TAC) is a project for accelerator based fundamental and applied researches supported by Turkish State Planning Organization (DPT). The proposed complex is consisted of 1 GeV electron linac and 3.56 GeV positron ring for a charm factory and a few GeV proton linac. Apart from the particle factory, it is also planned to produce synchrotron radiation from positron ring. In this study the lattice structure design of the positron storage ring is made to produce the third generation synchrotron light. The parameters of complementary undulators and wigglers are determined. It is shown that the insertion devices with the proposed parameter sets produce maximal spectral brightness to cover 10 eV - 100 keV photon energy range. |
|||
TU5RFP058 | 3D CAD Collaboration at European XFEL and ILC | linac, lattice, civil-engineering, survey | 1214 |
|
|||
In most sub-systems of the European XFEL, more than one institute participates in the design & development activities. This is the case for e.g. the cold linac, cryogenics, bunch compressors, undulators and photon beam systems. To ensure interface compatibility and make sure components fit into their complex environments, the collaborating institutes have to create high-level 3D models of their sub-systems. These 3D models are centrally integrated into a master model, which enables identification and elimination of collisions and non-conformities prior to manufacturing. A "collaborative design process", which supports efficient, interactive and inter-disciplinary cooperation of different institutes, has been successfully developed and established at the European XFEL. It consists of design guidelines and processes definitions for information & data exchange, reviews, approvals and change management. The process is supported by the DESY Engineering Data Management System, DESY EDMS, and allows the combination of 3D models from multiple 3D CAD systems. Following the good experience at the European XFEL, the same process is now established at the Global Design Effort for the ILC. |
|||
TU6PFP004 | Proton LINACs for Medical Applications | proton, linac, neutron | 1296 |
|
|||
AccSys has been built proton LINACs for medical applications such as Proton Beam Therapy (PBT), Positron Emission Tomography (PET) radioisotope production, and Boron Neutron Capture Therapy (BNCT). We will review the systems those have been shipped: For the PBT application, 6 systems have been shipped and under operation; for PET application, 5 systems have been shipped; for BNCT research application, one system has been shipped. We will also talk about high current proton linacs desired for BNCT and PET applications. |
|||
TU6RFP065 | MICE Particle Identification Systems | electron, factory, collider, emittance | 1696 |
|
|||
The international Muon Ionization Cooling Experiment (MICE) is being built at the Rutherford Appleton Laboratory (RAL), to demonstrate the feasibility of ionization cooling of muon beams. This is one of the major technological steps needed towards the development of a muon collider and a "neutrino factory" based on muon decays in a storage ring. MICE will use particle detectors to measure the cooling effect with high precision, planning to achieve an absolute accuracy on the measurement of emittance of 0.1% or better. The particle i.d. detectors and tracker must work under harsh environmental conditions due to high magnetic fringe fields and RF noise. We will describe the MICE particle i.d. detector systems, and show some current performance measurements of these detectors. |
|||
WE2RAI01 | The Development of a Superconducting Undulator for the ILC Positron Source | undulator, photon, wakefield, vacuum | 1839 |
|
|||
The ILC positron source relies upon a ~200 m long superconducting helical undulator in order to generate the huge flux of gamma photons required. The period is only 11.5 mm but the field strength is ~1 T. The UK is building and testing a full scale 4 m long ILC cryomodule at the moment. It will be completed in 2008 and the results used to demonstrate the feasibility of the full (200 m long) system. |
|||
|
|||
WE5PFP017 | Processing and Breakdown Localization Results for an L-Band Standing-Wave Cavity | cavity, plasma, ion, injection | 2024 |
|
|||
Funding: Work supported by the DOE under contract DE-AC02-76SF00515 An L-band (1.3 GHz), normal-conducting, five-cell, standing-wave cavity that was built as a prototype capture accelerator for the ILC is being high-power processed at SLAC. The goal is to demonstrate stable operation at 15 MV/m with 1 msec, 5 Hz pulses and the cavity immersed in a 0.5 T solenoidal magnetic field. This paper summarizes the performance that was ultimately achieved and describes a novel analysis of the modal content of the stored energy in the cavity after a breakdown to determine on which iris it occurred. |
|||
WE6PFP046 | Variations in Beam Phase and Related Issues Observed in KEKB | cavity, beam-loading, electron, betatron | 2595 |
|
|||
KEKB is a multi-bunch, high-current electron-positron collider. Newly installed crab cavities realized an effective head-on collision, while maintaining finite-angle crossing orbits. Bunches form a single train followed by a beam abort gap. We observed a beam phase advancing along a train due to transient beam loading. Since there is a difference in the beam phase between the two beams, a longitudinal displacement of the collision vertex is expected under the crabbing collision. Estimated variations agree with those detected by the Belle*. A displacement in the horizontal beam position was observed in correspondence with the variations in the beam phase. We found that the horizontal displacement was caused by a transverse kick of the crab cavities to phase-shifted bunches. Moreover, a rapid phase advancing was observed at the leading part in a train in the LER. We suspect that some longitudinal wakes with low Q values in accelerator components might contribute to the rapid change in the beam phase. *H. Kichimi et al., to be published. |
|||
WE6PFP072 | Ultimate Positron Polarization at ILC | polarization, undulator | 2665 |
|
|||
We are analyzing ILC positron source for best polarization and efficiency. 70% polarization looks feasible for 170 m undulator at 150 GeV. Conversion efficiency and polarization at 500 GeV considered also. We are making suggestions for reaching 80% positron polarization AT ILC as well. |
|||
WE6PFP080 | Optics Design for FACET | linac, optics, electron, focusing | 2685 |
|
|||
Funding: This work is supported by the Department of Energy contract DE-AC02-76SF00515. FACET is a proposed facility at SLAC National Accelerator Laboratory for beam driven plasma wakefield acceleration research. It is proposed to be built in the SLAC linac sector 20, where it will be separated from the LCLS located downstream and will gain the maximum beam energy from the upstream two kilometers of linac. FACET will also include an upgrade to linac sector 10, where a new e+ compressor chicane will be installed. The sector 20 will require a new optics consisting of two chicanes for e+ and e- bunch length compression, a final focus system and an extraction line. The two chicanes will allow the transport of e- and e+ bunches together, their simultaneous compression and proper positioning of e+ bunch behind e- at the plasma Interaction Point (IP). For a minimal cost, the new optics will mostly use the existing SLAC magnets. The desired beam parameters at the IP are: up to 23 GeV beam energy, 2·1010 charge per bunch, 10 micron round beam spot without dispersion and 25 micron bunch length. Details of the FACET optics design and results of particle tracking simulations are presented. |
|||
WE6RFP065 | The CLIC Positron Source Based on Compton Schemes | photon, laser, electron, linac | 2945 |
|
|||
The CLIC polarized positron source is based on a positron production scheme in which polarized photons are produced by Compton process. Compton backscattering happens in a so-called "Compton ring" where an electron beam of 1.06 GeV interacts with a powerful laser beam amplified in an optical resonator. The circularly-polarized gamma rays are sent on to a target, producing pairs of longitudinally polarized electrons and positrons. An Adiabatic Matching Device maximizes the capture of the positrons. A normal-conducting 2 GHz Linac accelerates the beam up to 2.424 GeV before injection into the Pre-Damping Ring (PDR). The nominal CLIC bunch population is 4.4x109 particles per bunch. Since the photon flux coming out from a "Compton ring" is not sufficient to obtain the requested charge, a stacking process is required in the PDR. Another option is to use a "Compton Energy Recovery Linac" where a quasi-continual stacking in the PDR could be achieved. A third option is to use a "Compton Linac" which would not require stacking. We describe the overall scheme as well as advantages and constraints of the three different options. |
|||
WE6RFP093 | Positron Acceleration by Using a Particle Beam-Driven Wake Field in Plasma | plasma, wakefield, electron, acceleration | 3013 |
|
|||
Plasma Wake Field Accelerator (PWFA) has a very attractive accelerating gradient which can be three orders of magnitude higher than that of the traditional accelerator. In this paper the positron acceleration in a particle beam driven PWFA is studied both in the linear and weakly nonlinear region by using Particle In Cell (PIC) simulation. A preliminary parameters design is obtained for such acceleration scheme. |
|||
TH5PFP047 | Electron Cloud Modeling Considerations at CesrTA | electron, space-charge, simulation, photon | 3306 |
|
|||
Funding: Support provided by the US National Science Foundation and the US Department of Energy The Cornell Electron Storage Ring (CESR) has recently begun operation as a test accelerator for next generation linear collider damping rings. This program, known as CesrTA, includes a thorough investigation of synchrotron radiation generated electron cloud effects. CESR is capable of operating with a variety of bunch patterns and beam currents, as well as with both electron and positron beams. Understanding the buildup of the cloud under these conditions requires the use of well validated simulation programs. This paper will discuss three such programs- POSINST, ECLOUD and CLOUDLAND, which have been benchmarked against each other in parameter regimes relevant to CesrTA operating conditions, with the aim of understanding systematic differences in the calculations. |
|||
TH5RFP027 | First Results from the CESRTA X-Ray Beam Size Monitor | photon, emittance, optics, damping | 3505 |
|
|||
Funding: NSF Engineering data sets were collected with the CESRTA x-ray beam size monitor (xBSM) during November 2008 and January 2009 runs. We report on the performance of the InGaAs photodiode array detector, including time response and signal-to-noise. We report on the observed measurement resolution for changes in the damping ring vertical beam size using the interchangeable optics elements: slits, coded apertures, and a Fresnel zone plates. Observed resolutions are compared to predictions based on characteristics of the optics elements. |
|||
TH5RFP047 | Particle Production in the MICE Beam Line | proton, target, factory, solenoid | 3558 |
|
|||
The MICE experiment aims at demonstrating that the performances of the muon ionization technique are compatible with the requirements of the neutrino factory and the muon collider. The experiment is running at the Rutherford-Appleton Laboratory in the UK using the ISIS proton beam on a dynamic target as a muon source. Brand new target system and muon beam line have been designed, built and installed during the last two years. On the other hand, particle identification detectors needed for the experiment have also been installed and commissioned. This presentation describes how we made use of Time of Flight detectors, aerogel Cherenkov counters and electro-magnetic calorimeter sensors to characterize the content of the MICE beam between 100 and 480 MeV/c. |
|||
TH5RFP057 | Fast Horizontal e+ Instability Measurements in DAΦNE | feedback, dipole, electron, simulation | 3585 |
|
|||
In the more than decennial history of DAΦNE, the Frascati e+/e- collider, the positron beam has always shown more difficulty to store high current than the e- beam. Given that the two rings are identical, many types of measurement have been tried to figure out the problem and to solve it, but eventually only one technique has presented a crucial utility: the modal grow rate measurement. In principle this method could be implemented using a commercial spectrum analyzer with the right software procedure inside. Nevertheless it is much easier and faster to record data by the bunch by bunch feedback diagnostics and to use for analyzing the offline feedback programs. A large campaign of data taking has been done in DAΦNE main rings during last fall. A comparison with grow rate records from previous years has point out clearly the difference with 2008 DAΦNE performance showing the way to solve the beam current limit. In particular, measurements have been done versus different machine conditions. Very fast horizontal instability present only in the e+ ring has been characterized showing linear behavior versus beam current. These data have been used to figure out the current limit problem. |
|||
TH5RFP058 | Beam Diagnostics of the Positron Beam at DAΦNE by 3+L Experiment | diagnostics, radiation, collider, photon | 3588 |
|
|||
At the LNF (Laboratori Nazionali di Frascati) of the INFN a novel diagnostics experiment has been set-up to monitor the real time bunch behavior in the positron ring of the DAΦNE collider. The experiment has been installed on a bending magnet exit port of the e+ ring. The front-end consists of a UHV chamber where a gold-coated plane mirror deflects the radiation through a ZnSe window. After the window, a compact optical layout in air focuses the radiation on an IR detector. Compact mid-IR fast uncooled HgCdTe photodiodes are used to measure the bunch by bunch emission. A preliminary alignment of the mirrors and a first characterization of the radiation emitted have been performed. Longitudinal measurements of the bunch behavior, both in time and in frequency domain, obtained with fast IR detectors are presented. This novel diagnostics now available is ready to allow monitoring in real time of the bunch-by-bunch positron emission. It has been designed to improve the DAΦNE diagnostics with the main aim to identify and characterize positron bunch instabilities in the longitudinal plane. Developments for extending detection capability in the transverse planes are in progress. |
|||
TH5RFP071 | The TE Wave Transmission Method for Electron Cloud Measurements at Cesr-TA | electron, damping, vacuum, coupling | 3606 |
|
|||
Funding: Supported by the U.S. Department of Energy under Contract No. DE-AC02-05CH11231. We report on the optimization of TE Wave measurements at the Cesr-TA ring at Cornell University. The CESR storage ring is currently used as a testbed for technologies to be used in the damping rings of the International Linear Collider. The TE Wave measurement method utilizes capacitive buttons (BPMs) in the ring to excite and detect a propagating electromagnetic wave corresponding to the beampipe's fundamental TE mode. The presence of low-energy electrons along the wave path changes its propagation characteristics, which can be detected by analyzing the received signal. By choosing the machine fill pattern (gaps and bunch trains length) it is possible to modulate the density of the electron cloud and derive information on its rise and fall times by observing the detected signal spectrum. The possibility of circulating both electron and positron beams in the ring enabled us to separate the contribution of primary photoelectrons, which are independent on the circulating particle nature, from the transverse resonant mechanism, which can increase the primary electron density many times over and which only takes place with a circulating positron beam. |
|||
TH6REP011 | Longitudinal Beam Diagnostics for the ILC Injectors and Bunch Compressors | diagnostics, simulation, electron, linac | 3971 |
|
|||
Funding: This work is supported by the U.S. Department of Energy under contract no. DE-FG02-06ER41435 with Northern Illinois University. We present a diagnostics suite and analyze techniques for setting up the longitudinal beam dynamics in ILC e- injectors and e+ and e- bunch compressors. Techniques to measure the first order moments and recover the first order longitudinal transfer map of the injector's intricate bunching scheme are presented. Coherent transition radiation diagnostics needed to measure and monitor the bunch length downstream of the ~5 GeV bunch compressor are investigated using a vector diffraction model. |
|||
TH6REP026 | An Ultrafast Laser-Wire Scanner Based on Electro-Optics | laser, electron, synchrotron, controls | 4006 |
|
|||
Funding: Work supported by the STFC LC-ABD collaboration and the Commission of the European Communities under the 6th Framework Programme Structuring the European Research Area, contract RIDS-RIDS-011899 A complete optical characterization of an electro-optic deflector to be used for fast laser-wire electron beam profilers performed using a 130 kHz repetition rate mode-locked laser, is presented. Incorporation of the device into the 2D laser-wire at PETRA III synchrotron at DESY is discussed. |
|||
TH6REP029 | Accelerator Physics Activity at the VEPP-4M Collider | feedback, electron, cavity, kicker | 4012 |
|
|||
The VEPP-4M electron-positron collider is now operating with the KEDR detector for high-energy physics experiments in the 1.5−2.0 GeV beam energy range. Parallel with these experiments, the VEPP-4M scientific team carries out a number of accelerator physics investigations. A new registration system for the Touschek polarimeter has been put into operation. A new NMR-based system for suppression of the guide field ripples has been developed. The counting rate of the Touschek particles has been measured as a function of the beam energy in the range from 1.85 to 4 GeV. The measurement results can be claimed at the future super B and C-Tau factories. For simultaneous measurement of the transverse beam position and inclination angle an X-ray multi-pinhole camera has been designed, manufactured and installed at the VEPP-4M. To suppress the longitudinal instability caused by high-order modes of the RF cavities, a feedback system has been developed. |
|||
TH6REP069 | Measurements of Coupled-Bunch Instabilities in BEPC-II | feedback, kicker, damping, electron | 4114 |
|
|||
BEPC-II is a two ring electron-positron collider designed to operate at 1 A beam currents. Longitudinal and transverse coupled-bunch instabilities have been observed in both electron and positron rings. In this paper we present measurements of both transverse and longitudinal instabilities with the identification of active eigenmodes, measurements of growth and damping rates, as well as of the residual beam motion levels. The measurements will then be used to estimate the growth rates at the design beam currents (yet to be achieved). We will also demonstrate how such data is used for specifying power amplifier and kicker parameters. |
|||
TH6REP072 | DAΦNE Horizontal Feedback Upgrade | feedback, damping, kicker, injection | 4123 |
|
|||
In this paper the horizontal feedback upgrade for the positron DAΦNE ring is presented. After having completed the analysis of the e+ current limit behavior, a feedback upgrade has been turned out necessary. For the success of the crab waist experiment in the 2008 year, a fast solution to implement the upgrade has been necessary. It has been considered if a simple power increase would be the best solution. The lack of power combiners and of space for other two power amplifiers has brought to a different approach, doubling the entire feedback system. The advantages of this implementation respect to a more traditional power amplifier doubling are evident: two feedback kicks every revolution turns, better use of the power amplifiers, greater reliability, and less coherent noise in the system. Measurements of the two feedbacks have shown a perfect equivalence of the new and the old system: in fact the resulting damping rate is exactly the double of each system taken individually. A description of the implementation is presented together with the performance of the system. |
|||
FR1RAI02 | The Conversion and Operation of the Cornell Electron Storage Ring as a Test Accelerator (CesrTA) for Damping Rings Research and Development | emittance, wiggler, electron, vacuum | 4200 |
|
|||
Funding: Support provided by the US National Science Foundation, the US Department of Energy, and the Japan/US Cooperation Program. In March of 2008, the Cornell Electron Storage Ring (CESR) concluded twenty eight years of colliding beam operations for the CLEO high energy physics experiment. We have reconfigured CESR as an ultra low emittance damping ring for use as a test accelerator (CesrTA) for International Linear Collider (ILC) damping ring R&D. The primary goals of the CesrTA program are to achieve a beam emittance approaching that of the ILC Damping Rings with a positron beam, to investigate the interaction of the electron cloud with both low emittance positron and electron beams, to explore methods to suppress the electron cloud, and to develop suitable advanced instrumentation required for these experimental studies (in particular a fast x-ray beam size monitor capable of single pass measurements of individual bunches). We report on progress with the CESR conversion activities, the status and schedule for the experimental program, and the first experimental results that have been obtained. |
|||
|
|||
FR5RFP017 | Investigation of a Gas Jet-Produced Hollow Plasma Wakefield Accelerator | plasma, ion, simulation, electron | 4566 |
|
|||
The effect of ion motion and the need for practical positron propagation in a plasma wakefield accelerator (PWFA) have incited interest in hollow plasma channels. These channels are typically assumed to be cylindrically symmetric; however, a different geometry might be easier to achieve. The introduction of an obstruction into the outlet of a high Mach number gas jet can produce two parallel slabs of gas separated by a density depression. Here, there is a detailed simulation study of the density depression created in such a system. This investigation reveals that the density depression is insufficient at the desired plasma density. However, insights from the simulations suggest another avenue for the creation of the hollow slab geometry. |
|||
FR5RFP025 | Simulations of Positron Beams Propagating in Plasma | plasma, emittance, simulation, focusing | 4586 |
|
|||
Funding: Work supported by the US Department of Energy Studies on propagation of electron beams in plasma have shown that in the blowout regime of the plasma wakefield accelerator (PWFA), the emittance of the incoming beam is preserved because of the linear focusing force exerted by a uniform ion column [1]. However, for positron beams the focusing force is nonlinear and they suffer emittance growth. We simulated the propagation of a positron beam in the uniform plasmas with different densities. We calculated the beam emittance from the simulation results and observed the beam size and emittance grow with increasing plasma density. Simulation results agree well with that of previous work. |
|||
FR5RFP043 | Simulations of Electron-Cloud Current Density Measurements in Dipoles, Drifts and Wigglers at CesrTA | simulation, wiggler, electron, dipole | 4628 |
|
|||
Funding: Supported by the US National Science Foundation, the US Department of Energy under Contracts No. DE-AC02-06CH11357, DE-AC02-05CH11231, and DE-AC02-76SF00515, and by the Japan/US Cooperation Program. CESR at Cornell has been operating as a damping ring test accelerator (CesrTA) with beam parameters approaching those anticipated for the ILC damping rings. A core component of the research program is to fully understand electron cloud effects in CesrTA. As a local probe of the electron cloud, several segmented retarding field analyzers (RFAs) have been installed in CesrTA in dipole, drift and wiggler regions. Using these RFAs, the energy spectrum of the time-average electron cloud current density striking the walls has been measured for a variety of bunch train patterns; with bunch populations up to 2x1010 per bunch, beam energies from 2 to 5 GeV, horizontal geometric emittances from roughly 10 to 133 nm, and bunch lengths of about 1 cm; and for both positron and electron beams. The effect of mitigation measures, such as coatings, has also been studied. This paper will compare these measurements with the predictions of simulation programs, and discuss the implications of these comparisons for our understanding of the physics of electron cloud generation and mitigation in ILC-like damping rings. |
|||
FR5RFP044 | Studies of the Effects of Electron Cloud Formation on Beam Dynamics at CesrTA | electron, dipole, simulation, photon | 4631 |
|
|||
Funding: National Science Foundation award 0734867 Office of Science, U.S. Department of Energy contracts DE-AC02-05CH11231 and DE-AC02-06CH11357 The Cornell Electron Storage Ring Test Accelerator (CesrTA) has commenced operation as a linear collider damping ring test bed following its conversion from an e+e- collider in 2008. A core component of the research program is the measurement of effects of synchrotron-radiation-induced electron cloud formation on beam dynamics. We have studied the interaction of the beam with the cloud in a number of experiments, including measurements of coherent tune shifts and emittance growth in various bunch train configurations, with different bunch currents, beam energies, beam emittance, and bunch lengths, for both positron and electron beams. This paper compares these measurements to modeling results from several advanced cloud simulation algorithms and discusses the implications of these comparisons for our understanding of the physics of electron cloud formation and decay in damping rings of the type proposed for future high-energy linear colliders. |
|||
FR5RFP068 | Demonstration of Electron Clearing Effect by Means of Clearing Electrodes and Groove Structures in High-Intensity Positron Ring | electron, insertion, wiggler, proton | 4689 |
|
|||
Funding: The Japan/US Cooperation Program Beam instability caused by the electron cloud is expected to be a limiting factor in the performance of future advanced positron and proton storage rings. In a wiggler section of the positron ring of the KEK B-factory (KEKB), we have installed a vacuum chamber with an insertion that can be replaced and including different techniques to study the mitigation of the electron-cloud effect in a high magnetic field region. We have installed an insertion with strip-line clearing electrode, an insertion with triangular grooves and an insertion with a smooth surface, and compared them each other under the same conditions. The electrode insertion is composed of a thin tungsten layer formed on a thin alumina ceramic layer. The groove insertion is composed of TiN-coated triangular grooves running longitudinally. In this paper, we report about the tests in the KEKB and about the large reduction in the measured electron cloud density when the clearing electrode and groove sections are installed with respect to the smooth insertion. These experiments are the first ones demonstrating the principle of the clearing electrode and groove insertions in a magnetic field. |
|||
FR5RFP070 | A Simulation Study of the Electron Cloud Instability at DAΦNE | electron, simulation, wiggler, space-charge | 4695 |
|
|||
Funding: Work supported in part by the “Ministero degli Affari Esteri, Direzione Generale per la Promozione e la Cooperazione Culturale” A strong horizontal instability has been observed in the DAΦNE positron ring since 2003. Experimental observations suggest an electron cloud induced coupled bunch instability as a possible explanation. In this communication we present a simulation study of the electron cloud coupled bunch instability for the DAΦNE positron ring, performed with the code PEI-M, and compare the numerical results with experimental observations. |
|||
FR5RFP084 | Simulations of Jitter Coupling due to Wakefields in the FACET Linac | electron, wakefield, linac, coupling | 4734 |
|
|||
Funding: Work supported by the DOE under contract DE-AC02-76SF00515. Facilities for Accelerator Science and Experimental Test Beams (FACET) is a proposed facility at SLAC that would use the initial two-thirds of the linac to transport e+ and e- beams to an experimental region. A principal use of this facility is to identify the optimum method for accelerating positrons in a beam driven plasma wakefield accelerator. To study this, a positron bunch, followed ½ an rf cycle later by an electron bunch, will be accelerated to an asymmetric chicane designed to move the positrons behind the electrons, and then on to the plasma wakefield test stand. A major focus of study was the coupling of jitter of the positron bunch to the electron bunch via linac wakes. Lucretia is a Matlab toolbox for the simulation of electron beam transport systems, capable of multi-bunch tracking and wakefield calculations. With the exception of the lack of support for tracking of electrons and positrons within a single bunch train, it was well suited to the jitter coupling studies. This paper describes the jitter studies, including modifications made to Lucretia to correctly simulate tracking of mixed-species bunch trains through a lattice of magnetic elements and em wakes. |
|||
FR5RFP086 | Analysis of the Wake Field Effects in the PEP-II SLAC B-Factory | vacuum, HOM, wakefield, cavity | 4740 |
|
|||
Funding: work supported by the Department of Energy under contract number DE-AC03-76SF00515 We present the history and analysis of different wake field effects throughout the operational life of the PEP-II SLAC B-factory. Although the impedance of the high and low energy rings is small, the high current intense beams generated a lot of power. These wake field effects are: heating and damage of vacuum beam chamber elements like RF seals, vacuum valves , shielded bellows, BPM buttons and ceramic tiles; vacuum spikes, vacuum instabilities and high detector background; beam longitudinal and transverse instabilities. We also discuss the methods used to eliminate these effects. Results of this analysis and the PEP-II experience may be very useful in the design of new storage rings and light sources. |