MEDSI2016 - List of Authors (Peña, G.)

Paper	Title	Page
TUPE11	Study on Thermal Mechanical Design and Optimization Analysis for the ALBA Infrared Microspectroscopy Beamline (MIRAS) Extraction Mirror Based on Finite Element Analysis	179
	M. Quispe, A. Carballedo, J.J. Casas, C. Colldelram, A. Crisol, G. Peña, L. Ribó, I. Sics, I. Yousef ALBA-CELLS Synchrotron, Cerdanyola del Vallès, Spain
	This paper reports design, modelling, simulation and optimization results for the ALBA MIRAS infrared radiation extraction mirror. Finite element analysis (FEA) was used to simulate the thermal mechanical behaviour of the device. With the aim to ensure a good thermal performance, conservative assumptions were applied: all of the incident Bending Magnet (BM) radiation is absorbed at the mirror surface, constant bending magnetic field and low thermal contact between the mirror Al 6061 and the OFHC copper arm. A novel solution has been implemented in order to provide an effective cooling by a natural convection on the in-air part of extraction mirror assembly. This has voided the necessity for a water cooling that often causes problems due to the associated vibrations. The power conditions were calculated by using SynRad+. The main ALBA Storage Ring design parameters are: 3 GeV, 400 mA and 1.42 T. According to these conditions, the mirror absorbs 15 W with a peak power density of 0.51 W/mm2. The peak temperature calculated was 63.2 °C. The real measurements reported during the commissioning stage showed a good thermal performance, in agreement with the results predicted by FEA.
	Poster TUPE11 [0.881 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-MEDSI2016-TUPE11
About •	paper received ※ 09 September 2016 paper accepted ※ 15 September 2016 issue date ※ 22 June 2017
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPE14	Study, Design and Optimization Analysis of the ALBA LOREA Dipole Vacuum Chamber and Crotch Absorbers Based on Finite Element Analysis	191
	M. Quispe, J. Campmany, J.J. Casas, C. Colldelram, A. Crisol, J. Marcos, G. Peña, M. Tallarida ALBA-CELLS Synchrotron, Cerdanyola del Vallès, Spain
	This work deals with the FEA study, design and optimization of the LOREA dipole vacuum chamber and Glidcop Al-15 crotch absorbers. At present LOREA is the ninth beam-line being designed at ALBA with an Insertion Device (ID) consisting of an Apple II-type helical undulator. For the standard dipole chamber the vertical polarized light hits the walls because of the very narrow vertical aperture between the cooling channels. In vertical mode the ID vertical divergence equals ± 2.2 mrad and the peak power density and total power are 5.6 kW/mrad² and 5.5 kW, respectively. Due to the high power a temperature as high as more than 600 °C is calculated. In consequence the dipole chamber has to be modified and the absorbers have to withstand the Bending Magnet (BM) and ID radiation. The new absorbers have to be thicker and its cooling channels are farer from BM power deposition than the standard absorbers. The thermal mechanical simulations show good results, the new absorbers are in a safe range, the maximum temperature, stress and strain are 309.2 °C, 164.2 MPa and 0.14%, respectively. The main ALBA Storage Ring design parameters used in the simulations are: 3 GeV, 400 mA and 1.42 T (BM).
	Poster TUPE14 [1.524 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-MEDSI2016-TUPE14
About •	paper received ※ 09 September 2016 paper accepted ※ 15 September 2016 issue date ※ 22 June 2017
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Study on Thermal Mechanical Design and Optimization Analysis for the ALBA Infrared Microspectroscopy Beamline (MIRAS) Extraction Mirror Based on Finite Element Analysis

179

M. Quispe, A. Carballedo, J.J. Casas, C. Colldelram, A. Crisol, G. Peña, L. Ribó, I. Sics, I. Yousef
ALBA-CELLS Synchrotron, Cerdanyola del Vallès, Spain

This paper reports design, modelling, simulation and optimization results for the ALBA MIRAS infrared radiation extraction mirror. Finite element analysis (FEA) was used to simulate the thermal mechanical behaviour of the device. With the aim to ensure a good thermal performance, conservative assumptions were applied: all of the incident Bending Magnet (BM) radiation is absorbed at the mirror surface, constant bending magnetic field and low thermal contact between the mirror Al 6061 and the OFHC copper arm. A novel solution has been implemented in order to provide an effective cooling by a natural convection on the in-air part of extraction mirror assembly. This has voided the necessity for a water cooling that often causes problems due to the associated vibrations. The power conditions were calculated by using SynRad+. The main ALBA Storage Ring design parameters are: 3 GeV, 400 mA and 1.42 T. According to these conditions, the mirror absorbs 15 W with a peak power density of 0.51 W/mm2. The peak temperature calculated was 63.2 °C. The real measurements reported during the commissioning stage showed a good thermal performance, in agreement with the results predicted by FEA.

Poster TUPE11 [0.881 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-MEDSI2016-TUPE11

About •

paper received ※ 09 September 2016 paper accepted ※ 15 September 2016 issue date ※ 22 June 2017

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPE14

Study, Design and Optimization Analysis of the ALBA LOREA Dipole Vacuum Chamber and Crotch Absorbers Based on Finite Element Analysis

191

M. Quispe, J. Campmany, J.J. Casas, C. Colldelram, A. Crisol, J. Marcos, G. Peña, M. Tallarida
ALBA-CELLS Synchrotron, Cerdanyola del Vallès, Spain

This work deals with the FEA study, design and optimization of the LOREA dipole vacuum chamber and Glidcop Al-15 crotch absorbers. At present LOREA is the ninth beam-line being designed at ALBA with an Insertion Device (ID) consisting of an Apple II-type helical undulator. For the standard dipole chamber the vertical polarized light hits the walls because of the very narrow vertical aperture between the cooling channels. In vertical mode the ID vertical divergence equals ± 2.2 mrad and the peak power density and total power are 5.6 kW/mrad² and 5.5 kW, respectively. Due to the high power a temperature as high as more than 600 °C is calculated. In consequence the dipole chamber has to be modified and the absorbers have to withstand the Bending Magnet (BM) and ID radiation. The new absorbers have to be thicker and its cooling channels are farer from BM power deposition than the standard absorbers. The thermal mechanical simulations show good results, the new absorbers are in a safe range, the maximum temperature, stress and strain are 309.2 °C, 164.2 MPa and 0.14%, respectively. The main ALBA Storage Ring design parameters used in the simulations are: 3 GeV, 400 mA and 1.42 T (BM).

Poster TUPE14 [1.524 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-MEDSI2016-TUPE14

About •

paper received ※ 09 September 2016 paper accepted ※ 15 September 2016 issue date ※ 22 June 2017

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)