• C. Eckardt, T. Bahlo, P. Bangert, R. Barday, U. Bonnes, M. Brunken, R. Eichhorn, J. Enders, M. Platz, Y. Poltoratska, M. Roth, F. Schneider, M. Wagner, A. Weber, B. Zwicker
  TU Darmstadt, Darmstadt
• W. Ackermann, W.F.O. Müller, T. Weiland
  TEMF, TU Darmstadt, Darmstadt

At the superconducting 130 MeV Darmstadt electron linac S-DALINAC* a source of polarized electrons** is being installed, extending the experimental capabilities with polarized electron and polarized photon probes for nuclear structure studies. This involves disassembling the existing low energy test stand and rebuilding the beam line in the accelerator hall. The beam itself is produced from a GaAs cathode by irradiation with a pulsed laser. The low-energy electron beam line includes diagnostic elements, a Wien filter for spin manipulation, a 100 keV Mott polarimeter for polarization measurement and a chopper-prebuncher section to modulate the time structure of the beam. At higher energies a 5-10 MeV Mott polarimeter and a 50-130 MeV Moeller polarimeter as well as a Compton transmission polarimeter will be installed to measure the beam polarization after acceleration. The Mott polarimeter is working with backscattered electrons under 165° scattering angle while for the Moeller polarimeter a wide-angle (3°-15°) spectrometer magnet was designed. We report on the performance of the test stand, the ongoing implementation, and the polarimeter research and development.

* A. Richter, Proc. EPAC 96, Sitges, p.110.
** Y. Poltoratska et al., AIP Conference Proc. 1149 (2009), p.983.

• J.K. Sekutowicz
  DESY, Hamburg
• P. Kneisel
  JLAB, Newport News, Virginia
• R. Nietubyc
  The Andrzej Soltan Institute for Nuclear Studies, Centre Swierk, Swierk/Otwock
• T. Rao, J. Smedley
  BNL, Upton, Long Island, New York

In this contribution, we report Quantum Efficiency (QE) test results with a hybrid lead/niobium superconducting RF (SRF) photoinjector at 2K and new Pb arc deposited cathodes at 300K. The ultimate goal of our effort is to build a Nb injector with the superconducting cathode made of lead, which, as reported in the past, demonstrated superior QE compared to other metallic superconducting elements. At first, we present the test results obtained with a 1.6-cell high purity Nb cavity with the emitting lead spot in the center of the back plate. The QE test results at room temperature and the SEM surface analysis of eight Pb cathodes, deposited recently under various conditions, are discussed in the second part of this contribution.

• A. Ushakov, S. Riemann, A. Schälicke
  DESY Zeuthen, Zeuthen

The development of an intense polarised positron sources provides a challenge for a new generation of linear colliders. The software framework Geant4, a toolkit for simulation of the passage of particles trough matter, features tracking capabilities of charged particles in electromagnetic fields, and also includes the description of polarisation transfer in scattering processes. Based on Geant4 a novel simulation tool, PPS-Sim*, has been developed to optimise the design and to determine polarisation, beam properties, as well as energy deposition in accelerator components. All source components and their parameters can be chosen easily and flexible. Helical undulator, laser-Compton and coherent Bremsstrahlung in crystals are available as positron production schemes. Target materials and geometry can be adjusted. Flux concentrator, quarter wave transformer and lithium lens are implemented as possible capture devices. Geometry, accelerating components and magnetic field configuration can be specified by the user. In this contribution, PPS-Sim will be presented, and selected results for linear collider applications will be discussed.

* PPS-Sim web page - http://pps-sim.desy.de

• M. Kuriki, H. Iijima
  HU/AdSM, Higashi-Hiroshima
• H. Hayano, Y. Honda, H. Sugiyama, J. Urakawa
  KEK, Ibaraki
• G. Isoyama, S. Kashiwagi, R. Kato
  ISIR, Osaka
• E. Katin, E. Khazanov, V. Lozhkarev, G. Luchinin, A. Poteomkin
  IAP/RAS, Nizhny Novgorod
• G. Shirkov, G.V. Trubnikov
  JINR, Dubna, Moscow Region

Aim of Super-conducting Test Facility (STF) at KEK is demonstrating technologies for International Linear Collider. In STF, one full RF unit will be developed and beam acceleration test will be made. In super-conducting accelerator, precise RF control in phase and power is essential because the input RF power should be balanced to beam accelerating power. To demonstrate the system feasibility, the beam accelerating test is an important step in R&D phase of STF and ILC. To provide ILC format beam for STF, we develop an electron source based on photo-cathode L-band RF gun. To generate ILC format beam, we developed a laser system based on Yb fiber oscillator in 40.6 MHz. The pulse repetition is decreased by picking pulses in 2.7 MHz, which meets ILC bunch spacing, 364 ns. The pulse is then amplified by YLF laser up to 8 uJ per pulse in 1 mm. The light is converted to 266 nm by SHG and FHG. Finally, 1.5 uJ per pulse is obtained and 3.2 nC bunch charge will be made. We report the basic performance of the laser system from the accelerator technology point of a view.

• H. Tomizawa, H. Dewa, H. Hanaki, A. Mizuno, T. Taniuchi
  JASRI/SPring-8, Hyogo-ken

We have developed a laser-induced Schottky-effect-gated photocathode gun since 2006. This new type of gun utilizes a laser's coherency to realize a compact laser source using Z-polarization of the IR laser on the cathode. This Z-polarization scheme reduces the laser pulse energy by reducing the cathode work function due to Schottky effect. Before this epoch-making scheme, photocathode guns had never utilized laser's coherency. A hollow laser incidence is applied with a hollow convex lens that is focused after passing the beam through a radial polarizer. According to our calculations (convex lens: NA=0.15), a Z-field of 1 GV/m needs 1.26 MW at peak power for the fundamental wavelength (792 nm) and 0.316 MW for the SHG (396 nm). Therefore, we expect that this laser-induced Schottky emission requires just a compact femtosecond laser oscillator as a laser source. Besides, a dichromatic laser scheme (photo-exciting: 780 nm; gating: 30 um) should be applied to polarized electron sources for International Linear Collider (ILC). We report the first feasibility study of this laser-induced Schottky-effect on several metal photocathodes by comparing radial and azimuthal polarizations.

• A. Deshpande
  Sokendai, Ibaraki
• S. Araki, M.K. Fukuda, N. Terunuma, J. Urakawa
  KEK, Ibaraki
• K. Sakaue, M. Washio
  RISE, Tokyo

At Laser Undulator Compact Source (LUCX) at KEK, we designed and made a new RF Gun with high mode separation of 8.6 MHz and high Q value as compared to earlier guns. This paper presents fabrication details, low power measurements and tuning procedures followed in making the gun cavity. We also discuss in detail, experimentation done using this gun and show the measurement results. Currently we produce 100 bunch per train but we plan to go for 300 or more bunch per train operation. This will make possible to have higher charge available for laser-beam collisions to generate high flux soft X-rays by Inverse Compton Scattering at our setup.

• K. Kan, T. Kondoh, T. Kozawa, K. Norizawa, A. Ogata, J. Yang, Y. Yoshida
  ISIR, Osaka

Time resolution of pulse radiolysis, which is a stroboscopic measurement technique, depends on electron bunch length. In order to improve the time resolution, femtosecond electron bunch generation at photocathode rf gun was investigated. A 1.6-cell S-band photocathode rf gun, similar to the Gun IV type at Brookhaven National Laboratory (BNL), was used. The rf gun consisted of a half cell and a full cell. A copper cathode was located in the half cell. The rf gun was driven by femtosecond UV laser pulse (266 nm), which was generated with third-harmonic-generation (THG) of Ti:Sapphire femtosecond laser (800 nm). The longitudinal and transverse dynamics of the electron bunch generated by the UV laser was investigated. The bunch length was measured with the dependence of energy spread on acceleration phase in a linac, which was set at the downstream of the rf gun. Transverse emittance at the linac exit was also measured with Q-scan method.

• T. Kondoh, K. Kan, T. Kozawa, K. Norizawa, A. Ogata, J. Yang, Y. Yoshida
  ISIR, Osaka

Femtosecond electron beam pulse radiolysis which has time resolution of 250 fs was achieved by a Photocathode RF gun LINAC in the ISIR, Osaka University. And geminate ion recombination (charged pair dynamics) in n-dodecane was studied. Kinetics of the Radical cation of n-dodecane was measured. As a result, the existence of the excited-radical cation, and generation of the radical cation via relaxation from the excited-radical cation were suggested. Those new results were obtained in the field of the radiation chemistry by the photocathode RF gun.

• J. Yang, K. Kan, T. Kondoh, Y. Murooka, N. Naruse, K. Tanimura, Y. Yoshida
  ISIR, Osaka
• J. Urakawa
  KEK, Ibaraki

Both ultrafast time-resolved radiolysis and electron diffraction based on photocathode rf electron guns have been developed in Osaka University to reveal the hidden dynamics of intricate molecular and atomic processes in materials. One of the photocathode rf guns has been used successfully to produce a 100-fs high-brightness electron single bunch with a booster linear accelerator and a magnetic bunch compressor. The time resolution of 240 fs was achieved at the first time in the pulse radiolysis. Another photocathode rf gun, which produces directly a near-relativistic 100-fs electron beam, has been developed to construct femtosecond electron diffraction. The megavolt electron diffraction patterns have been observed. The dependences of the emittance, bunch length and energy spread on the radio-frequency (rf) and space charge effects in the rf gun were investigated.

• M.Y. Yoshida, M. Aoki, Y. Kuno, A. Sato
  Osaka University, Osaka
• T. Nakamoto, T. Ogitsu, K. Tanaka, A. Yamamoto
  KEK, Ibaraki

An intense muon beam is mandatory for the next-generation experiments to search for lepton flavor violating processes in the muon sector. The COMET experiment, J-PARC ·10²¹, aims to search for muon to electron conversion with an unprecedented sensitivity.. The muon beam is produced from pion decays in a strong magnetic field generated by superconducting solenoid coils. The large-bore superconducting coils enclose the pion-production target to capture pions with a large solid angle. The magnetic field is designed to have a peak of 5T at the target. To avoid severe radiation from the target, thick shielding is inserted in the warm bore of the pion capture solenoid magnet. The proton beam is injected through the gap between the pion capture solenoid and the subsequent transport solenoid magnets. For this purpose, the bore of the pion capture solenoid has to be larger than 1 m. This paper describes the design of the pion capture solenoid magnet for the COMET experiment.

• Y. Yokoyama, T. Aoki, K. Sakaue, T. Suzuki, M. Washio, J. Yokose
  RISE, Tokyo
• H. Hayano, N. Terunuma, J. Urakawa
  KEK, Ibaraki
• S. Kashiwagi
  ISIR, Osaka
• R. Kuroda
  AIST, Tsukuba, Ibaraki

At Waseda University, we have been studying a high quality electron beam generation and its application experiments with Cs-Te photocathode RF-Gun. We have already succeeded in generating a stable high-charged single-bunch electron beam. To generate more intense electron beam, we designed a multi-bunch electron linac and developed the multi-pulse UV laser which irradiates to the cathode. The target values of the number of electron bunch and bunch charges are 100 bunches/train and 800 pC/bunch, respectively. In addition, we adopted the method of the amplitude modulation of the incident RF pulse to the S-band klystron in order to compensate the energy difference in each bunch because of the slow rise time of acceleration voltage in cavity and beam loading effect in the accelerating structure. In this conference, we will report design properties of our multi-bunch electron linac, the results of the multi-bunch electron beam diagnosis and the energy difference compensation using the RF amplitude modulation method.

• M. Petrarca, E. Chevallay, A.E. Dabrowski, M. Divall Csatari, S. Döbert, D. Egger, V. Fedosseev, T. Lefèvre, R. Losito, O. Mete
  CERN, Geneva

The high charge PHIN photo injector is studied at CERN as an electron source for the CLIC Test Facility (CTF3) drive beam as an alternative to the present thermionic gun. The objective of PHIN is to demonstrate the feasibility of a laser-based electron source for CLIC. The photo injector operates with a 2.5 cell, 3 GHz RF gun using a Cs2Te photocathode illuminated by UV laser pulses generated by amplifying and frequency quadrupling the signal from a Nd:YLF oscillator running at 1.5GHz. The challenge is to generate a beam structure of 1908μbunches with 2.33nC perμbunch at 1.5GHz leading to a high integrated train charge of 4446nC and nominal beam energy of 5.5MeV with current stability below 1%. In the present test stand, a segmented beam dump has been implemented allowing a time resolved measurement of the energy and energy spread of the electron beam. In this paper we report and discuss the measured transverse and longitudinal beam parameters for both the full and time gated train of bunches, and the obtained photocathode quantum efficiency. Laser pointing and amplitude stability results are discussed taking into account correlation between laser and electron beam.

• I.R. Bailey, J.A. Clarke, D.J. Scott
  Cockcroft Institute, Warrington, Cheshire
• I.R. Bailey
  Lancaster University, Lancaster
• C.G. Brown, J. Gronberg, L.B. Hagler, W.T. Piggott
  LLNL, Livermore, California
• L.J. Jenner
  Imperial College of Science and Technology, Department of Physics, London
• L. Zang
  The University of Liverpool, Liverpool

The efficiency of future positron sources for the next generation of high-energy particle colliders (e.g. ILC, CLIC, LHeC) can be improved if the positron-production target is immersed in the magnetic field of adjacent capture optics. If the target is also rotating due to heat deposition considerations then eddy currents may be induced and lead to additional heating and stresses. In this paper we present data from a rotating target wheel prototype for the baseline ILC positron source. The wheel has been operated at revolution rates up to 1800rpm in fields of the order of 1 Tesla. Comparisons are made between torque data obtained from a transducer on the target drive shaft and the results of finite-element simulations. Rotordynamics issues are presented and future experiments on other aspects of the positron source target station are considered.

• L. Zang
  Cockcroft Institute, Warrington, Cheshire
• I.R. Bailey
  Lancaster University, Lancaster
• M. Korostelev, A. Wolski
  The University of Liverpool, Liverpool

CLIC will need of order 10 to the 14 positrons per second to achieve its specified luminosity. For such a challenge, an undulator based scheme has been proposed as one of the options for the positron source. As CLIC may operate over a wide range of energy (from 0.5 TeV to 3 TeV), there is a large margin for us to push the performance of the whole system to be more efficient. We report on the undulator parameters and optimization of components of the source such as conversion target, AMD, solenoid and capture RF for different operational scenarios. In addition to maximizing the positron yield the polarization of the positron beam are also considered.

• W. Liu, W. Gai
  ANL, Argonne
• L. Rinolfi
  CERN, Geneva
• J. Sheppard
  SLAC, Menlo Park, California

We propose a viable positron source scheme that uses circularly polarized gamma rays generated from the main 250 GeV electron beam. The beam passes through a helical superconducting undulator with a magnetic field of ~ 1 Tesla and a period of a few centimeters. The gamma-rays produced in the undulator in the energy range between ~ 3 MeV ~ 100 MeV will be directed to a titanium target and produces polarized positrons. The positrons are then captured, accelerated and transported to a damping ring. Detailed parameter studies of this scheme including positron yield, undulator parameter dependence and target composition and geometry will be presented. Effects on the 250 GeV drive beam, including emittance, energy spread and energy loss from the beam passing through the undulator will also be discussed.

• W. Liu, W. Gai
  ANL, Argonne

We present an update on the ANL ILC positron source study. We examined the impact of different drive beam energies on the positron yield and polarization for the ILC RDR baseline undulator. The e⁺ yield is found to drop rapidly as the drive beam energy is reduced. We studied different undulator parameters for their effect on the positron yield and polarization when working at lower drive beam energies. Using a lower K (B field level) can increase the photon energy, but it is still very difficult to bring the yield up for low drive beam energies. For 250 GeV drive beam options, we studied the RDR undulator performance as a function of K. Instead of powering off some sections of the undulator, one can also consider lowering the B field to bring the positron yield back to the desired 1.5 e+/e-. We also studied the liquid lead target option for ILC positron source and the energy deposition in the reference design Ti target wheel.

• J. Gronberg, A. Abbott, C.G. Brown, J.B. Javedani, W.T. Piggott
  LLNL, Livermore, California
• J.A. Clarke
  STFC/DL/ASTeC, Daresbury, Warrington, Cheshire

The positron source at a future TeV scale electron linear collider will need to generate positrons at a rate two orders of magnitude larger than have been previously achieved. We report on a design of a 3.5 Tesla pulsed flux concentrator magnet which uses liquid nitrogen cooling of the flux concentrator plates to reduce the electrical resistance leading to reduced energy deposition and the ability to generate the required 1 ms pulse duration. This magnet can double the collection efficiency of positrons emitted from the target.