A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z    

Chan, J.

Paper Title Page
TPPT021 Characterization and Tuning of a Microwave Gun Cavity 1748
 
  • W.K. Lau, J. Chan, L.-H. Chang, C.W. Chen, H.Y. Chen, K.-T. Hsu, S.Y. Hsu, J.-Y. Hwang, Y.C. Wang, T.-T. Yang
    NSRRC, Hsinchu
  
  The SSRL rf gun cavity is electromagnetic structure with a half-cell at the cathode end and a full cell at the other end. Instead of coupling through beam pipe to produce the desired pi-mode for beam acceleration, these two cells are coupled through a frequency tunable side-coupled cell. Therefore, the strucuture is actually 3-cell cavity and the pi/2-mode will be used. This paper reports the characterization of these resonant modes at various side-coupled cell tuning conditions. And the behavior of this cavity will also be analytically examined.  
TPPT031 Coupler Design for the LCLS Injector S-Band Structures 2176
 
  • Z. Li, L.D. Bentson, J. Chan, D. Dowell, C. Limborg-Deprey, J.F. Schmerge, D.C. Schultz, L. Xiao
    SLAC, Menlo Park, California
  
  Funding: Work supported by the U.S. DOE Contract No. DE-AC03-76SF00515.

The LCLS injector is required to provide a 1-nC, 10-ps bunch with a normalized rms transverse projected emittance of less than 1.0-μm. The LCLS beam is generated and accelerated in a 1.6-cell S-band RF gun to 6-MeV followed by two SLAC 3-m S-band accelerator structures to further accelerate the beam to 135 MeV to move it out of the space-charge dominated regime. In the SLAC S-band structures, the RF power feed is through a single coupling-hole (single-feed coupler) which results in a field asymmetry. The time dependent multipole fields in the coupler induce a transverse kick along the bunch and cause the emittance to increase above the LCLS specification. To meet the stringent emittance requirements for the injector, the single-feed couplers will be replaced by a dual-feed racetrack design to minimize the multipole field effects. We will present detailed studies of the multipole fields in the S-band coupler and the improvements with the dual-feed racktrack design using the parallel finite element eigenmode solver Omega3P.

 
ROAC004 High Gradient Performance of NLC/GLC X-Band Accelerating Structures 372
 
  • S. Doebert, C. Adolphsen, G.B. Bowden, D.L. Burke, J. Chan, V.A. Dolgashev, J.C. Frisch, R.K. Jobe, R.M. Jones, R.E. Kirby, J.R. Lewandowski, Z. Li, D.J. McCormick, R.H. Miller, C.D. Nantista, J. Nelson, C. Pearson, M.C. Ross, D.C. Schultz, T.J. Smith, S.G. Tantawi, J.W. Wang
    SLAC, Menlo Park, California
  • T.T. Arkan, C. Boffo, H. Carter, I.G. Gonin, T.K. Khabiboulline, S.C. Mishra, G. Romanov, N. Solyak
    Fermilab, Batavia, Illinois
  • Y. Funahashi, H. Hayano, N. Higashi, Y. Higashi, T. Higo, H. Kawamata, T. Kume, Y. Morozumi, K. Takata, T. T. Takatomi, N. Toge, K. Ueno, Y. Watanabe
    KEK, Ibaraki
  
  Funding: Work Supported by DOE Contract DE-AC02-76F00515.

During the past five years, there has been an concerted effort at FNAL, KEK and SLAC to develop accelerator structures that meet the high gradient performance requirements for the Next Linear Collider (NLC) and Global Linear Collider (GLC) initiatives. The structure that resulted is a 60-cm-long, traveling-wave design with low group velocity (< 4% c) and a 150 degree phase advance per cell. It has an average iris size that produces an acceptable short-range wakefield in the linacs, and dipole mode damping and detuning that adequately suppresses the long-range wakefield. More than eight such structures have operated over 1000 hours at a 60 Hz pulse rate at the design gradient (65 MV/m) and pulse length (400 ns), and have reached breakdown rate levels below the limit for the linear collider. Moreover, the structures are robust in that the breakdown rates continue to decrease over time, and if the structures are briefly exposed to air, the rates recover to their low values within a few days. This paper presents a final summary of the results from this program, which effectively ended last August with the selection of ‘cold’ technology for a next generation linear collider.