Will, I.
| Paper | Title | Page |
|---|---|---|
| MOPP034 | Upgrades of the Laser Beam-line at PITZ | 110 |
|
||
|
Funding: This work has partly been supported by the European Community, contract numbers RII3-CT-2004-506008 and 011935, an by the "Impunls-und Vernetzungsfonds" of the Helmholtz Association, contract number VH-FZ-05 In spring of 2005 an essential upgrade of the photocathode laser and of the 27 m long laser beam-line took place at PITZ. A detectable improvement of the laser beam profile at the photocathode is expected. This improvement should lead to an additional reduction of the transverse emittance of the electron beam. The upgraded laser consists of a fully laser diode pumped scheme of pulse train oscillator, pre-amplifiers and booster amplifiers. The main advantages of this upgrade are improved stability, easier maintenance and long-term operations at 10 Hz repetition rate. In addition, the scheme of the optical beam-line was changed: The distance between the beam shaping aperture and the cathode was strongly reduced. Therefore a further improvement of the laser beam profile at the photocathode is expected. The laser beam-line is upgraded by an enlarged number of remotely controlled optical elements that allows the fine tuning of the laser beam characteristics during the running. New diagnostics tools are included in the laser beam-line. The paper focuses on the design of the new optical beam-line. It describes the results of electron beam measurements using the upgraded laser and the new PITZ2 electron beam-line in detail. |
||
| FROA005 | Optical Laser Synchronized to the DESY VUV-FEL for Two-Color Pump-Probe Experiments | 690 |
|
||
|
Funding: This work was funded by the European Commission under Contract no. HPRI-CT-1999-50009 The VUV-FEL at DESY provides ultra-short pulses with pulse durations below 50 fs. To explore a wider field of time resolved experiments a complex laser system has been installed delivering 150 fs pulses at a wavelength of 800 nm with 50 μJ pulse energy at 1MHz repetition rate during the FEL burst (of 800 μs). In order to perform two color pump-probe experiments the laser has to be synchronized to the FEL. To ensure precise and reliable synchronized operation of the laser, various diagnostic experiments have been developed. Concepts as well as first results of the synchronization will be shown. |
||
| THPP033 | Diagnostics Beamline for the SRF Gun Project | 530 |
|
||
|
Funding: Funded by the Bundesministerium für Bildung und Forschung, the State of Berlin and the Zukunftsfonds Berlin A superconducting rf photo electron injector (SRF gun) is currently under construction by a collaboration between BESSY, DESY, FZR and MBI. The project aims at the design and setup of an CW SRF gun including a diagnostics beamline for the ELBE FEL and to address R&D issues on low emittance injectors for future light sources such as the BESSY FEL. Of critical importance for the injector performance is the control of the electron beam parameters. For this reason a compact diagnostics beamline is under development serving a multitude of operation settings ranging from low-charge (77pC), low-emittance (1 pi mm mrad) mode to high-charge (2.5nC) operation of the gun. For these operation modes beam dynamics simulations are resulting in boundary conditions for the beam instrumentation. Proven and mature technology is projected wherever possible, for example for current and beam position monitoring. The layout of the beam profile and emittance measurement systems is described. For the bunch length, which varies between 5 and 50 ps, two schemes using Electro-optical sampling and Cherenkov radiation are detailed. The beam energy and energy spread is measured with an especially designed 180 degree spectrometer. |
||
| THPP034 | Progress of the Rossendorf SRF Gun Project | 534 |
|
||
|
A superconducting rf photo electron injector (SRF gun) is under development at the Forschungszentrum Rossendorf. The project aims at several issues: improvement of the beam quality for the ELBE superconducting electron linac, demonstration of feasibility of this gun type, investigation of critical components, and parameter studies for future application (BESSY-FEL, 4GLS). In 2005, a substantial progress has been made. The two 3.5-cell niobium cavities for the gun have been delivered from the company ACCEL. The main parts for gun cryostat like vacuum vessel, cryogenic and magnetic shields are ready. Test benches for the cathode cooling system and the cavity tuner are being assembled. The photo cathode preparation lab has been arranged, and the diagnostic beam line has been designed (see T. Kamps et al., this conference). After delivering the gun cavities, their rf properties are being measured at room temperature and the warm tuning is being carried out. The set-up for this treatment and measurement as well as the results will be presented. |
||
| THPP043 | Status and First Results from the Upgraded PITZ Facility | 564 |
|
||
|
Funding: This work has been partly supported by the European Community, contract numbers RII3-CT-2004-506008 and 011935, and by the 'Impuls- und Vernetzungsfonds" of the Helmholtz Association, contract number VH-FZ-05. Since December 2004, the photo injector test facility at DESY in Zeuthen (PITZ) has been upgraded. A normal conducting copper booster cavity has been installed and the diagnostics beamline has been strongly modified. An extended water cooling system has been installed and was successfully taken into operation. Actually, the new diagnostics elements are being commissioned. After the installation of the new 10 MW klystron in June/July, the gun can be conditioned towards higher average power, and the whole beamline including the booster will be taken into operation. First results from the commissioning phase including gun and booster conditioning are reported. |
||