SRF2013 - List of Authors (Amini, B.)

Paper	Title	Page
THP020	Measuring the Higher Order Mode Spectrum of the TRIUMF 9-cell Cavity	936
	P. Kolb, B. Amini, R.E. Laxdal, Y. Ma, Z.Y. Yao, V. Zvyagintsev TRIUMF, Canada's National Laboratory for Particle and Nuclear Physics, Vancouver, Canada
	The ARIEL eLINAC consists of five nine cell cavities, produced by PAVAC, and will accelerate 10 mA electrons to 50 MeV. This 500 kW beam will be used for rare isotope production. Future upgrade plans include a recirculating beam line. Recirculating the beam, for either energy doubling or energy recovery to drive a FEL, brings the risk of multi-pass beam break up (BBU). Therefore it is necessary to avoid higher order modes (HOMs) with high shunt impedance. The goal of the cavity design is to reduce the highest shunt impedance of any dipole HOM to 1 *10⁶Ω or less. Measurements on the nine cell cavity with bead pulling have been done to identify dipole modes and their geometric shunt impedance R/Q as well as measurements at 2 K to estimate the quality factor of those HOMs. Results of these measurements will be shown and compared to computer simulations done with ACE3P.

THP035	Production of a 1.3 GHz Niobium 9-cell TRIUMF-PAVAC Cavity for the ARIEL Project	978
	V. Zvyagintsev, B. Amini, P.R. Harmer, P. Kolb, R.E. Laxdal, Y. Ma, B.S. Waraich, Z.Y. Yao TRIUMF, Canada's National Laboratory for Particle and Nuclear Physics, Vancouver, Canada R. Edinger, M.C. Leustean, R. Singh PAVAC, Richmond, B.C., Canada
	A nine-cell 1.3 GHz superconducting niobium cavity has been fabricated for the ARIEL project at TRIUMF. The cavity is intended to accelerate a beam current of 10 mA at an accelerating gradient of 10 MV/m. The beam loaded RF power of 100 kW is supplied through two opposed fundamental power couplers. The electromagnetic design was done by TRIUMF. The cavity final design and fabrication procedure have been developed in collaboration between TRIUMF and PAVAC Industries Inc. Several innovations in the cavity fabrication process were developed at PAVAC. Since the most important weld is at the equator this weld is done first to form a ‘smart-bell’ as the basic unit as opposed to welding first at the iris to form ‘dumb-bell’ units. Each half cell is pressed with a male die into a plastic forming surface to produce half-cells with less shape distortion and material dislocations. The cavity fabrication sequence including the frequency tuning steps and RF frequency modelling methods will be discussed.

Paper

Title

Page

Measuring the Higher Order Mode Spectrum of the TRIUMF 9-cell Cavity

936

P. Kolb, B. Amini, R.E. Laxdal, Y. Ma, Z.Y. Yao, V. Zvyagintsev
TRIUMF, Canada's National Laboratory for Particle and Nuclear Physics, Vancouver, Canada

The ARIEL eLINAC consists of five nine cell cavities, produced by PAVAC, and will accelerate 10 mA electrons to 50 MeV. This 500 kW beam will be used for rare isotope production. Future upgrade plans include a recirculating beam line. Recirculating the beam, for either energy doubling or energy recovery to drive a FEL, brings the risk of multi-pass beam break up (BBU). Therefore it is necessary to avoid higher order modes (HOMs) with high shunt impedance. The goal of the cavity design is to reduce the highest shunt impedance of any dipole HOM to 1 *10⁶Ω or less. Measurements on the nine cell cavity with bead pulling have been done to identify dipole modes and their geometric shunt impedance R/Q as well as measurements at 2 K to estimate the quality factor of those HOMs. Results of these measurements will be shown and compared to computer simulations done with ACE3P.

THP035

Production of a 1.3 GHz Niobium 9-cell TRIUMF-PAVAC Cavity for the ARIEL Project

978

V. Zvyagintsev, B. Amini, P.R. Harmer, P. Kolb, R.E. Laxdal, Y. Ma, B.S. Waraich, Z.Y. Yao
TRIUMF, Canada's National Laboratory for Particle and Nuclear Physics, Vancouver, Canada
R. Edinger, M.C. Leustean, R. Singh
PAVAC, Richmond, B.C., Canada

A nine-cell 1.3 GHz superconducting niobium cavity has been fabricated for the ARIEL project at TRIUMF. The cavity is intended to accelerate a beam current of 10 mA at an accelerating gradient of 10 MV/m. The beam loaded RF power of 100 kW is supplied through two opposed fundamental power couplers. The electromagnetic design was done by TRIUMF. The cavity final design and fabrication procedure have been developed in collaboration between TRIUMF and PAVAC Industries Inc. Several innovations in the cavity fabrication process were developed at PAVAC. Since the most important weld is at the equator this weld is done first to form a ‘smart-bell’ as the basic unit as opposed to welding first at the iris to form ‘dumb-bell’ units. Each half cell is pressed with a male die into a plastic forming surface to produce half-cells with less shape distortion and material dislocations. The cavity fabrication sequence including the frequency tuning steps and RF frequency modelling methods will be discussed.