IPAC2014 - List of Authors (Yang, Y.L.)

Paper	Title	Page
TUPRO097	Magnets and Magnetic Field Measurements of Hefei Light Source II	1268
	Q. Luo, N. Chen, G. Feng, N. Hu, K. Tang, Y.L. Yang, J.J. Zheng USTC/NSRL, Hefei, Anhui, People's Republic of China
	Funding: Work supported by Natural Science Foundation of China 11005106, 11105141, and 11375178. The paper introduces magnets and magnetic field measurements of Hefei Light Source II. In the year 2012-2014, NSRL of USTC upgraded the HLS to HLS II. The HLS II, which was built to improve the performance of the light source, in particular to get higher brilliance of synchrotron radiation and increase the number of straight section insertion devices, is now at commissioning stage. Main purpose of this stage is to achieve full energy with high current, fine emittance and enough life time based on adjustment of magnet current, RF voltage and so on. Most of the magnets were replaced during this project. A new magnetic field measurement platform was built and used for the sampling test on new magnets. Test results showed that the discreteness and uniformity of integrated magnetic field of magnets all meet the requirements.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-TUPRO097
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME141	Design of Beam Intensity Measurement System in Injector for HLS II	3581
	C. Cheng, P. Lu, B.G. Sun, K. Tang, J. Xu, Y.L. Yang, Z.R. Zhou, J.Y. Zou USTC/NSRL, Hefei, Anhui, People's Republic of China
	A new beam intensity measurement (BIM) system has been developed and has been used in the upgrade project of HLS II. After the upgrading is accomplished, electron energy in Injector endpoint will increase from 200MeV to 800MeV to achieve the goal of top-off injector. Meanwhile, macro pulse width changes from 1us to 1ns and peak intensity from 50mA to 1A approximately. So three fast current transformers (FCTs) and two integrating current transformer (ICTs) are installed in Linac and Transport Line to measure single pass beam parameters. In this article, off-line calibration of beam transformer is elaborated. Since the fast pulse signals from beam transformer will be hugely distorted after they transmit from Injector vacuum chamber to the Injector beam diagnostic centre room after hundreds of meters long LMR-400 cable, signal recovery algorithm based on FFT/IFFT is used to re-appear the true original signal and calculate the calibration efficient. In the end, resolution and measurement result of the BIM system is presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME141
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME142	Design of the Beam Profile Monitors for THz Source Based FEL	3584
	J. Liu, P. Lu, B.G. Sun, K. Tang, J.G. Wang, J. Xu, Y.L. Yang, Z.R. Zhou USTC/NSRL, Hefei, Anhui, People's Republic of China
	Design of the Beam Profile Monitors for THz Source Based FEL* J. Liu, P. Lu, B. G. Sun#, Y. J. Pei, Y. L. Yang, Z.R. Zhou, J. G. Wang, K. Tang, J. Xu NSRL, School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230029, P. R. China Abstract To meet requirements of high performance THz-FEL, a compact FEL facility was proposed. In order to characterize the beam, some beam profile monitors were designed. There are four flags for beam profiles in Linac，one pop-in monitor for high precision beam profile inside a small-gap undulator, and two screens to measure the beam energy spread and emittance of Linac. On one hand, we need to use software to control the position of these profile monitors, on the other hand, we need screens to display the results. This paper describes how to design and control these monitors, as well as how to measure the beam parameter.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME142
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME143	Measuring Energy Spread Using Beam Screen Monitor and Four Strip-Line Electrodes for Hls II Injector*	3587
SUSPSNE076	use link to see paper's listing under its alternate paper code
	K. Tang, J. Liu, P. Lu, Q. Luo, B.G. Sun, H. Xu, J. Xu, Y.L. Yang, Z.R. Zhou, J.Y. Zou USTC/NSRL, Hefei, Anhui, People's Republic of China
	In order to nondestructively measure the beam energy spread with a beam energy of 0.8GeV in the injector at the upgrade project of Hefei Light Source (HLS II) in real time, a beam energy spread monitor (BESM) using beam position monitor (BPM) with four stripline electrodes has been developed. And a screen monitor (SM) near the BESM is used to measure beam energy spread destructively. This paper introduces in brief the beam position measurement system and beam transverse profile measurement system. The relationship between the transverse size at the BESM and at the SM (Flag3) is discussed in detail in this report. The result shows that energy spread measuring result of BESM and SM is 0.19% and 0.18% respectively. So we can draw a conclusion that the BESM is capable of nondestructively measuring the beam energy spread.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME143
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME144	Stripline Beam Position Monitor for THz Source Based FEL	3590
	J. Xu, L. Li, J. Liu, P. Lu, Y.J. Pei, B.G. Sun, K. Tang, J.G. Wang, F.F. Wu, H. Xu, Y.L. Yang, Z.R. Zhou, J.Y. Zou USTC/NSRL, Hefei, Anhui, People's Republic of China
	A 14MeV Linac with both the micro-pulse repetition rate 2856MHz and the macro-pulse width 6us for the THz Source Based FEL was proposed. In order to measure the beam position, a stripline beam position monitor (BPM) was designed, and a commercial BPM electronics Libera Brilliance Single Pass was adopted. As the input carrier frequency of the BPM electrode signal is 2856MHz, but the operating frequency of the Libera Brilliance Single Pass is 500MHz, so a front-end electronics was needed before the electrode signals feed into Libera Brilliance Single Pass. The front-end electronics was designed to make the BPM electrode signals of 2856MHz convert to 500MHz.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME144
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME145	BPM Signal Channel Characterization Test based on TDR for HLS II Storage Ring	3593
	J.J. Zheng, C. Cheng, P. Lu, Q. Luo, B.G. Sun, Y.L. Yang, Z.R. Zhou USTC/NSRL, Hefei, Anhui, People's Republic of China
	A new BPM system on the upgraded Hefei light source (HLSII) storage ring is installed. Before the machine commissioning, the BPM system should be carefully tested, such as the conductivity and integrity of BPM signal channels from button electrodes to digital beam position processors (pickups, cables and connectors). This paper presents an experience of signal channel test based on time domain reflection (TDR) for HLS II storage ring BPM system. Basing on the wave propagation method, an analytic expression for the signal from TDR on BPM signal channel is briefly introduced. The conductivity and integrity of the BPM signal channels can be verified by comparing the TDR waveform to theory signal. All the BPM signal channels are tested by the TDR in order to verify electronic characteristic and the usability. And some breakdowns are analysed and handled.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME145
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Magnets and Magnetic Field Measurements of Hefei Light Source II

1268

Q. Luo, N. Chen, G. Feng, N. Hu, K. Tang, Y.L. Yang, J.J. Zheng
USTC/NSRL, Hefei, Anhui, People's Republic of China

Funding: Work supported by Natural Science Foundation of China 11005106, 11105141, and 11375178.
The paper introduces magnets and magnetic field measurements of Hefei Light Source II. In the year 2012-2014, NSRL of USTC upgraded the HLS to HLS II. The HLS II, which was built to improve the performance of the light source, in particular to get higher brilliance of synchrotron radiation and increase the number of straight section insertion devices, is now at commissioning stage. Main purpose of this stage is to achieve full energy with high current, fine emittance and enough life time based on adjustment of magnet current, RF voltage and so on. Most of the magnets were replaced during this project. A new magnetic field measurement platform was built and used for the sampling test on new magnets. Test results showed that the discreteness and uniformity of integrated magnetic field of magnets all meet the requirements.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-TUPRO097

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME141

Design of Beam Intensity Measurement System in Injector for HLS II

3581

C. Cheng, P. Lu, B.G. Sun, K. Tang, J. Xu, Y.L. Yang, Z.R. Zhou, J.Y. Zou
USTC/NSRL, Hefei, Anhui, People's Republic of China

A new beam intensity measurement (BIM) system has been developed and has been used in the upgrade project of HLS II. After the upgrading is accomplished, electron energy in Injector endpoint will increase from 200MeV to 800MeV to achieve the goal of top-off injector. Meanwhile, macro pulse width changes from 1us to 1ns and peak intensity from 50mA to 1A approximately. So three fast current transformers (FCTs) and two integrating current transformer (ICTs) are installed in Linac and Transport Line to measure single pass beam parameters. In this article, off-line calibration of beam transformer is elaborated. Since the fast pulse signals from beam transformer will be hugely distorted after they transmit from Injector vacuum chamber to the Injector beam diagnostic centre room after hundreds of meters long LMR-400 cable, signal recovery algorithm based on FFT/IFFT is used to re-appear the true original signal and calculate the calibration efficient. In the end, resolution and measurement result of the BIM system is presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME141

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME142

Design of the Beam Profile Monitors for THz Source Based FEL

3584

J. Liu, P. Lu, B.G. Sun, K. Tang, J.G. Wang, J. Xu, Y.L. Yang, Z.R. Zhou
USTC/NSRL, Hefei, Anhui, People's Republic of China

Design of the Beam Profile Monitors for THz Source Based FEL* J. Liu, P. Lu, B. G. Sun#, Y. J. Pei, Y. L. Yang, Z.R. Zhou, J. G. Wang, K. Tang, J. Xu NSRL, School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230029, P. R. China Abstract To meet requirements of high performance THz-FEL, a compact FEL facility was proposed. In order to characterize the beam, some beam profile monitors were designed. There are four flags for beam profiles in Linac，one pop-in monitor for high precision beam profile inside a small-gap undulator, and two screens to measure the beam energy spread and emittance of Linac. On one hand, we need to use software to control the position of these profile monitors, on the other hand, we need screens to display the results. This paper describes how to design and control these monitors, as well as how to measure the beam parameter.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME142

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME143

Measuring Energy Spread Using Beam Screen Monitor and Four Strip-Line Electrodes for Hls II Injector*

3587

SUSPSNE076

use link to see paper's listing under its alternate paper code

K. Tang, J. Liu, P. Lu, Q. Luo, B.G. Sun, H. Xu, J. Xu, Y.L. Yang, Z.R. Zhou, J.Y. Zou
USTC/NSRL, Hefei, Anhui, People's Republic of China

In order to nondestructively measure the beam energy spread with a beam energy of 0.8GeV in the injector at the upgrade project of Hefei Light Source (HLS II) in real time, a beam energy spread monitor (BESM) using beam position monitor (BPM) with four stripline electrodes has been developed. And a screen monitor (SM) near the BESM is used to measure beam energy spread destructively. This paper introduces in brief the beam position measurement system and beam transverse profile measurement system. The relationship between the transverse size at the BESM and at the SM (Flag3) is discussed in detail in this report. The result shows that energy spread measuring result of BESM and SM is 0.19% and 0.18% respectively. So we can draw a conclusion that the BESM is capable of nondestructively measuring the beam energy spread.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME143

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME144

Stripline Beam Position Monitor for THz Source Based FEL

3590

J. Xu, L. Li, J. Liu, P. Lu, Y.J. Pei, B.G. Sun, K. Tang, J.G. Wang, F.F. Wu, H. Xu, Y.L. Yang, Z.R. Zhou, J.Y. Zou
USTC/NSRL, Hefei, Anhui, People's Republic of China

A 14MeV Linac with both the micro-pulse repetition rate 2856MHz and the macro-pulse width 6us for the THz Source Based FEL was proposed. In order to measure the beam position, a stripline beam position monitor (BPM) was designed, and a commercial BPM electronics Libera Brilliance Single Pass was adopted. As the input carrier frequency of the BPM electrode signal is 2856MHz, but the operating frequency of the Libera Brilliance Single Pass is 500MHz, so a front-end electronics was needed before the electrode signals feed into Libera Brilliance Single Pass. The front-end electronics was designed to make the BPM electrode signals of 2856MHz convert to 500MHz.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME144

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME145

BPM Signal Channel Characterization Test based on TDR for HLS II Storage Ring

3593

J.J. Zheng, C. Cheng, P. Lu, Q. Luo, B.G. Sun, Y.L. Yang, Z.R. Zhou
USTC/NSRL, Hefei, Anhui, People's Republic of China

A new BPM system on the upgraded Hefei light source (HLSII) storage ring is installed. Before the machine commissioning, the BPM system should be carefully tested, such as the conductivity and integrity of BPM signal channels from button electrodes to digital beam position processors (pickups, cables and connectors). This paper presents an experience of signal channel test based on time domain reflection (TDR) for HLS II storage ring BPM system. Basing on the wave propagation method, an analytic expression for the signal from TDR on BPM signal channel is briefly introduced. The conductivity and integrity of the BPM signal channels can be verified by comparing the TDR waveform to theory signal. All the BPM signal channels are tested by the TDR in order to verify electronic characteristic and the usability. And some breakdowns are analysed and handled.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME145

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)