KEK, Ibaraki
SLAC, Menlo Park, California
Coherent synchrotron radiation (CSR) is generated when a bunched beam traverses a dipole magnet or a wiggler/undulator. It can degrade the beam quality in both storage rings and linacs through enhancing the beam energy spread and lengthening the bunch length, even cause single-bunch microwave instabilities. Using several methods, CSR impedances in the positron damping ring (DR) of the SuperKEKB which is under design were calculated. From the impedances due to CSR, resistive wall and various vacuum components, quasi-Green function wake potentials were constructed and used in simulations of Particle-In-Cell (PIC) tracking. We present the CSR related results in this paper.
KEK, Ibaraki
As part of the design works of the interaction region (IR) of SuperKEKB (the upgrade of KEKB B-factory (KEKB)), the loss factor and impedance of beam ducts for the interaction point (IP duct) were calculated by GdfiedL. The IP duct is round and connected to beam ducts for electron and positron beams with a diameter of 20 mm via Y-shaped crotch ducts at both ends. The lengths of the straight section and crotch section are about 200 mm, respectively. The beam crossing angle is 83 mrad. Calculations for two types of IP duct were performed. Both ducts are almost same in design except for the diameter of the straight section (20 mm and 30 mm). The loss factors were about 0.001 V/pC in both cases when the bunch length was 6 mm. The longitudinal impedances showed that there were no modes trapped longitudinally in IP duct. However, from the results of the transverse impedance and eigenmode calculation, it was found that many TE modes can be trapped at the crotch section if the beam is off-center of the beam duct. For comparison, the loss factor and impedance of the IR beam duct of KEKB are also being calculated now. Full details of the calculation results will be provided in this report.
KEK, Ibaraki
SLAC, Menlo Park, California
Grooved surfaces are effective to suppress the secondary electron emission, and can be a possible technique to mitigate the electron cloud instability (ECI) in positron/proton storage rings. Various types of triangular grooved surfaces have been studied in a laboratory, and also using an intense positron beam of the KEKB B-factory. The grooves have vertex angles of 20 ~ 30 degrees, and depths of 2.5 mm. In the laboratory, the secondary electron yield (SEY) of sample pieces were measured using an electron beam in a magnetic-free condition. The maximum SEY well below 1.0 was obtained after some extent of electron bombardment for most of grooved surfaces. To test he groove efficacy in magnetic field regions of particle accelerators, insertions with several types of grooved surfaces were installed into a test chamber in a wiggler magnet of KEKB positron ring. In a dipole-like chamber wit magnetic field (0.78 T), the reduction in the electron density around the beam was observed for a grooved section when compared to the case of a flat surface with TiN coating. An R&D effort is underway to optimize and manufacture the grooved surface in accelerator beam pipes for practical use.
KEK, Ibaraki
SLAC, Menlo Park, California
In order to mitigate the electron cloud instability (ECI) in a positron ring, an electron clearing electrode with a very thin structure has been developed. The electrode has been tested with an intense positron beam of the KEKB B-factory using a test chamber. A drastic reduction in the electron density around the beam was demonstrated in a dipole magnetic field (0.78 T). The clearing electrode was then applied to the actual copper beam pipe (94 mm in diameter) with antechambers for wiggler magnets of KEKB. The feed-through was revised to improve reliability, and the length was modified to fit a real magnet. The input power into the electrode was estimated to be approximately 80 W/m. The clear reduction in the electron density was also observed by applying a voltage of +500 V to the electrode. The design of clearing electrodes has now reached a high reliability and it is suitable for accelerator applications.
CLASSE, Ithaca, New York
CERN, Geneva
Carleton University, College of Natural Sciences, Ottawa, Ontario
Purdue University, West Lafayette, Indiana
LBNL, Berkeley, California
Grove City College, Grove City, Pennsylvania
INFN/LNF, Frascati (Roma)
ASCo, Clayton, Victoria
KEK, Ibaraki
Clarkson University, Potsdam, New York
BNL, Upton, Long Island, New York
ANL, Argonne
CalPoly, San Luis Obispo, CA
Cockcroft Institute, Warrington, Cheshire
SLAC, Menlo Park, California
Fermilab, Batavia
Technion, Haifa
Loyola University, Chicago, Illinois
The Cornell Electron Storage Ring (CESR) has been reconfigured as a test accelerator (CesrTA) for a program of electron cloud (EC) research at ultra low emittance. The instrumentation in the ring has been upgraded with local diagnostics for measurement of cloud density and with improved beam diagnostics for the characterization of both the low emittance performance and the beam dynamics of high intensity bunch trains interacting with the cloud. Finally a range of EC mitigation methods have been deployed and tested. Measurements of cloud density and its impact on the beam under a range of conditions will be presented and compared with simulations. The effectiveness of a range of mitigation techniques will also be discussed.
KEK, Ibaraki
University of Tokyo, Tokyo
Tohoku University, Graduate School of Science, Sendai
SuperKEKB is the upgrade plan of the current B-factory experiment with the KEKB accelerator at KEK. Its luminosity is designed to be 8x1035 /cm2/s (40 times higher than KEKB) and the integrated luminosity is expected to be 50 ab-1. In SuperKEKB, it is important to evaluate the beam induced BG and design the interaction region (IR) to assure the stable detector operation. To estimate the beam induced BG, we construct the beam-line simulation based on the GEANT4 simulation. In this paper, we report the BG evaluation and the IR design for SuperKEKB.
KEK, Ibaraki
Super-KEKB, an upgrade plan of the present KEKB collider, has recently changed its scheme from 'high current' option to 'nano-beam' scheme. In the latter the current is relatively low(4A/2.3A for LER/HER ring) compared to that of the high-current option(9.4A/4.1A), while the vertical beam size is squeezed to 60 nm at the interaction point to get the high luminosity. The emittance of the injected beam should be low and, since the Tousheck lifetime is very short(600 sec), the intensity of the positron beam is as high as 8 nC/pulse. For the electron beam a low-emittance high-intensity RF gun is adopted. For the positron beam a damping ring has been proposed. The design of the damping ring has been performed for the high-current option*. In this paper an updated design for the nano-beam scheme is presented.
* Nucl. Instr. Meth. A 556 (2006) 13-19
KEK, Ibaraki
KEKB is an e-/e+ collider for the study of B physics and is also used for machine studies for future machines. The peak luminosity of KEKB, which is the world-highest value, has been still increasing. This report summarizes recent progress at KEKB.
SLAC, Menlo Park, California
LBNL, Berkeley, California
CLASSE, Ithaca, New York
INFN/LNF, Frascati (Roma)
ANL, Argonne
Cockcroft Institute, Warrington, Cheshire
KEK, Ibaraki
CERN, Geneva
As part of the International Linear Collider (ILC) collaboration, we have compared the electron cloud effect for different Damping Ring designs respectively with 6.4 km and 3.2 km circumference and investigated the feasibility of a shorter damping ring with respect to the electron cloud build-up and related beam instability. These studies were carried out with beam parameters of the ILC Low Power option. A reduced damping ring circumference has been proposed for the new ILC baseline design and would allow to considerably reduce the number of components, wiggler magnets and costs. We also briefly discuss the plans for future studies including the luminosity upgrade option with shorter bunch spacing, the evaluation of mitigations and the integration of the CesrTA results into the Damping Ring design.