• K. Yonehara
  
• R. J. Abrams, M. A.C. Cummings, R. P. Johnson, S. A. Kahn, T. J. Roberts
  Muons, Inc, Batavia
• D. R. Broemmelsiek, M. Hu, A. Jansson, V. D. Shiltsev
  Fermilab, Batavia, Illinois

MANX is an experiment to prove that effective six-dimensional (6D) muon beam cooling can be achieved a Helical Cooling Channel (HCC) using ionization-cooling with helical and solenoidal magnets in a novel configuration. The aim is to demonstrate that 6D muon beam cooling is understood well enough to plan intense neutrino factories and high-luminosity muon colliders. The experiment consists of the HCC magnets that envelop a liquid helium energy absorber, upstream and downstream instrumentation to measure the particle or beam parameters before and after cooling, and emittance matching sections between the detectors and the HCC. We describe and compare the experimental configuration for both single particle and beam profile measurement techniques based on G4Beamline simulations.

• S. A. Kahn
  
• M. Alsharo'a, R. P. Johnson
  Muons, Inc, Batavia
• V. Kashikhin, V. S. Kashikhin, K. Yonehara, A. V. Zlobin
  Fermilab, Batavia, Illinois

A helical cooling channel consisting of a pressurized gas absorber imbedded in a magnetic channel that provides superimposed solenoidal, helical dipole and helical quadrupole fields has shown considerable promise in providing six-dimensional cooling of muon beams. The analysis of this muon cooling technique with both analytic and simulation studies has shown significant reduction of muon phase space. A particular channel that has been simulated is divided into four segments each with progressively stronger fields and smaller apertures to reduce the equilibrium emittance so that more cooling can occur. The fields in the helical channel are sufficiently large that the conductor for segments 1 and 2 can be Nb3Sn and the conductor for segments 3 and 4 may need to be high temperature superconductor. This paper will describe the magnetic specifications for the channel and two conceptual designs on how to implement the magnetic channel.

• V. S. Kashikhin
  
• R. P. Johnson, S. A. Kahn, T. J. Roberts
  Muons, Inc, Batavia
• V. Kashikhin, M. J. Lamm, G. Romanov, K. Yonehara, A. V. Zlobin
  Fermilab, Batavia, Illinois

MANX is a 6-dimensional muon ionization-cooling experiment that has been proposed to Fermilab to demonstrate the use of a Helical Cooling Channel (HCC) for future muon colliders and neutrino factories. The HCC for MANX has solenoidal, helical dipole, and helical quadrupole magnetic components which diminish as the beam loses energy as it slows down in a liquid helium absorber inside the magnets. Two superconducting magnet system designs are described which use quite different approaches to providing the needed fields. Additional magnets that provide emittance matching between the HCC and upstream and downstream spectrometers are also described as are the results of G4Beamline simulations of the beam cooling behaviour of the complete magnet and absorber system.

• M. A.C. Cummings
  
• C. M. Ankenbrandt, K. Yonehara
  Fermilab, Batavia, Illinois
• R. P. Johnson
  Muons, Inc, Batavia

The study of rare processes using stopping muon beams provides access to new physics that cannot be addressed at energy frontier machines. The flux of muons into a small stopping target is limited by the kinematics of the production process and by stochastic processes in the material used to slow the particles. Innovative muon beam cooling techniques are being applied to the design of stopping muon beams in order to increase the event rates in such experiments. Such intense stopping beams will also aid the development of applications such as muon spin resonance and muon-catalyzed fusion.

• A. Jansson
  
• V. Balbekov, D. R. Broemmelsiek, M. Hu, N. V. Mokhov, K. Yonehara
  Fermilab, Batavia, Illinois

Within the framework of the Fermilab Muon Collider Task Force, the possibility of developing a dedicated muon test beam for cooling experiments has been investigated. Cooling experiments can be performed in a very low intensity muon beam by tracking single particles through the cooling device. With sufficient muon intensity and large enough cooling decrement, a cooling demonstration experiment may also be performed without resolving single particle trajectories, but rather by measuring the average size and position of the beam. This allows simpler, and thus cheaper, detectors and readout electronics to be used. This paper discusses muon production using 400MeV protons from the linac, decay channel and beamline design, as well as the instrumentation required for such an experiment, in particular as applied to testing the Helical Cooling Channel (HCC) proposed by Muons Inc.

• M. BastaniNejad
  
• M. Alsharo'a, P. M. Hanlet, R. P. Johnson, M. Kuchnir, D. J. Newsham
  Muons, Inc, Batavia
• C. M. Ankenbrandt, A. Moretti, M. Popovic, K. Yonehara
  Fermilab, Batavia, Illinois
• A. A. Elmustafa
  Old Dominion University, Norfolk, Virginia
• D. M. Kaplan
  Illinois Institute of Technology, Chicago, Illinois

Microscopic images of the surfaces of metallic electrodes used in high-pressure gas-filled 800 MHz RF cavity experiments are used to investigate the mechanism of RF breakdown. The images show evidence for melting and boiling in small regions of ~10 micron diameter on tungsten, molybdenum, and beryllium electrode surfaces. In these experiments, the dense hydrogen gas in the cavity prevents electrons or ions from being accelerated to high enough energy to participate in the breakdown process so that the only important variables are the fields and the metallic surfaces. The distributions of breakdown remnants on the electrode surfaces are compared to the maximum surface gradient E predicted by an ANSYS model of the cavity. The surface local density of spark remnants, presumably the probability of breakdown, shows a power law dependence on the maximum gradient, with E¹⁰ for tungsten and molybdenum and E⁷ for beryllium. This is reminiscent of Fowler-Nordheim behavior of electron emission from a cold cathode, which is explained by the quantum-mechanical penetration of a barrier that is characterized by the work function of the metal.

• Y. Alexahin
  
• R. B. Palmer
  BNL, Upton, Long Island, New York
• K. Yonehara
  Fermilab, Batavia, Illinois

For muons with preferable for ionization cooling momentum <300MeV/c the longitudinal motion is naturally undamped. In order to provide the longitudinal damping a correlation between muon momentum and transverse position - described in terms of the dispersion function - should be introduced. In the present report we consider the possibility of dispersion generation in a periodic sequence of alternating solenoids (FOFO channel) by choosing the tune in the second passband (i.e. above half-integer per cell) and tilting the solenoids in adjacent cells in the opposite direction. Analytical estimates as well as simulation results for equilibrium emittances and cooling rates are presented.