PAC07 - List of Authors (Smith, S.)

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Smith, S.

Paper	Title	Page
WEOBAB01	Electromagnetic Background Tests for the ILC Interaction Point Feedback System	1970
	P. Burrows R. Arnold, S. Molloy, S. Smith, G. R. White, M. Woods SLAC, Menlo Park, California G. B. Christian, C. I. Clarke, B. Constance, A. F. Hartin, H. D. Khah, C. Perry, C. Swinson, G. R. White JAI, Oxford A. Kalinin STFC/DL/ASTeC, Daresbury, Warrington, Cheshire
	We present results obtained with the T-488 experiment at SLAC Endstation A (ESA). A material model of the ILC extraction-line design was assembled and installed in ESA. The module includes materials representing the mask, beamline calorimeter, and first extraction quadrupole, encompassing a stripline interaction-point feedback system beam position monitor (BPM). The SLAC high-energy electron beam was used to irradiate the module in order to mimic the electromagnetic (EM) backgrounds expected in the ILC interaction region. The impact upon the performance of the feedback BPM was measured, and compared with detailed simulations of its expected response.
	Slides
WEOCAB01	Design of the Beam Delivery System for the International Linear Collider	1985
	A. Seryi I. V. Agapov, G. A. Blair, S. T. Boogert, J. Carter Royal Holloway, University of London, Surrey M. Alabau, P. Bambade, J. Brossard, O. Dadoun LAL, Orsay J. A. Amann, R. Arnold, F. Asiri, K. L.F. Bane, P. Bellomo, E. Doyle, A. F. Fasso, L. Keller, J. Kim, K. Ko, Z. Li, T. W. Markiewicz, T. V.M. Maruyama, K. C. Moffeit, S. Molloy, Y. Nosochkov, N. Phinney, T. O. Raubenheimer, S. Seletskiy, S. Smith, C. M. Spencer, P. Tenenbaum, D. R. Walz, G. R. White, M. Woodley, M. Woods, L. Xiao SLAC, Menlo Park, California M. Anerella, A. K. Jain, A. Marone, B. Parker BNL, Upton, Long Island, New York D. A.-K. Angal-Kalinin, C. D. Beard, J.-L. Fernandez-Hernando, P. Goudket, F. Jackson, J. K. Jones, A. Kalinin, P. A. McIntosh STFC/DL/ASTeC, Daresbury, Warrington, Cheshire R. Appleby UMAN, Manchester J. L. Baldy, D. Schulte CERN, Geneva L. Bellantoni, A. I. Drozhdin, V. S. Kashikhin, V. Kuchler, T. Lackowski, N. V. Mokhov, N. Nakao, T. Peterson, M. C. Ross, S. I. Striganov, J. C. Tompkins, M. Wendt, X. Yang Fermilab, Batavia, Illinois K. Buesser DESY, Hamburg P. Burrows, G. B. Christian, C. I. Clarke, A. F. Hartin OXFORDphysics, Oxford, Oxon G. Burt, A. C. Dexter Cockcroft Institute, Warrington, Cheshire J. Carwardine, C. W. Saunders ANL, Argonne, Illinois B. Constance, H. Dabiri Khah, C. Perry, C. Swinson JAI, Oxford O. Delferriere, O. Napoly, J. Payet, D. Uriot CEA, Gif-sur-Yvette C. J. Densham, R. J.S. Greenhalgh STFC/RAL, Chilton, Didcot, Oxon A. Enomoto, S. Kuroda, T. Okugi, T. Sanami, Y. Suetsugu, T. Tauchi KEK, Ibaraki A. Ferrari UU/ISV, Uppsala J. Gronberg LLNL, Livermore, California Y. Iwashita Kyoto ICR, Uji, Kyoto W. Lohmann DESY Zeuthen, Zeuthen L. Ma STFC/DL, Daresbury, Warrington, Cheshire T. M. Mattison UBC, Vancouver, B. C. T. S. Sanuki University of Tokyo, Tokyo V. I. Telnov BINP SB RAS, Novosibirsk E. T. Torrence University of Oregon, Eugene, Oregon D. Warner Colorado University at Boulder, Boulder, Colorado N. K. Watson Birmingham University, Birmingham H. Y. Yamamoto Tohoku University, Sendai
	The beam delivery system for the linear collider focuses beams to nanometer sizes at the interaction point, collimates the beam halo to provide acceptable background in the detector and has a provision for state-of-the art beam instrumentation in order to reach the physics goals. The beam delivery system of the International Linear Collider has undergone several configuration changes recently. This paper describes the design details and status of the baseline configuration considered for the reference design.
	Slides
THPMN079	Simulation of ILC Feedback BPM Signals in an Intense Background Environment	2889
	A. F. Hartin R. Arnold, S. Molloy, S. Smith, M. Woods SLAC, Menlo Park, California P. Burrows, G. B. Christian, C. I. Clarke, B. Constance, H. D. Khah, C. Perry, C. Swinson, G. R. White JAI, Oxford A. Kalinin STFC/DL/ASTeC, Daresbury, Warrington, Cheshire
	Funding: This work is supported in part by the Commission of the European Communities under the 6th Framework Programme "Structuring the European Research Area", contract number RIDS-011899. Experiment T-488 at SLAC, End Station A recorded distorted BPM voltage signals and an accurate simulation of these signals was performed. Geant simulations provided the energy and momentum spectrum of the incident spray and secondary emissions, and a method via image charges was used to convert particle momenta and number density into BPM stripline currents. Good agreement was achieved between simulated and measured signals. Further simulation of experiment T-488 with incident beam on axis and impinging on a thin radiator predicted minimal impact due to secondary emission. By extension to worst case conditions expected at the ILC, simulations showed that background hits on BPM striplines would have a negligible impact on the accuracy of beam position measurements and hence the operation of the FONT feedback system
FRPMN111	Design and Performance of the LCLS Cavity BPM System	4366
	R. M. Lill L. H. Morrison, W. E. Norum, N. Sereno, G. J. Waldschmidt, D. R. Walters ANL, Argonne, Illinois S. Smith, T. Straumann SLAC, Menlo Park, California
	Funding: Work supported by U. S. Department of Energy under Contract Nos. DE-AC02-06CH11357 and DE-AC03-76SF00515 In this paper we present the design of the beam position monitor (BPM) system for the LCLS undulator, which features a high resolution X-band cavity BPM. Each BPM has a TM010 monopole reference cavity and a TM110 dipole cavity designed to operate at a center frequency of 11.384 GHz. The signal processing electronics features a low-noise single-stage three-channel heterodyne receiver that has selectable gain and a phase locking local oscillator. We will discuss the system specifications, design, and prototype test results.
FRPMS049	Resolution of a High Performance Cavity Beam Position Monitor System	4090
	S. Walston S. T. Boogert Royal Holloway, University of London, Surrey C. C. Chung, P. Fitsos, J. Gronberg LLNL, Livermore, California J. C. Frisch, S. Hinton, J. May, D. J. McCormick, S. Smith, T. J. Smith, G. R. White SLAC, Menlo Park, California H. Hayano, Y. Honda, N. Terunuma, J. Urakawa KEK, Ibaraki Yu. G. Kolomensky, T. Orimoto UCB, Berkeley, California P. Loscutoff LBNL, Berkeley, California A. Lyapin, S. Malton, D. J. Miller UCL, London R. Meller Cornell University, Department of Physics, Ithaca, New York M. C. Ross Fermilab, Batavia, Illinois M. Slater, M. Thomson, D. R. Ward University of Cambridge, Cambridge V. Vogel DESY, Hamburg
	International Linear Collider (ILC) interaction region beam sizes and component position stability requirements will be as small as a few nanometers. It is important to the ILC design effort to demonstrate that these tolerances can be achieved – ideally using beam-based stability measurements. It has been estimated that RF cavity beam position monitors (BPMs) could provide position measurement resolutions of less than one nanometer and could form the basis of the desired beam-based stability measurement. We have developed a high resolution RF cavity BPM system. A triplet of these BPMs has been installed in the extraction line of the KEK Accelerator Test Facility (ATF) for testing with its ultra-low emittance beam. A metrology system for the three BPMs was recently installed. This system employed optical encoders to measure each BPM's position and orientation relative to a zero-coefficient of thermal expansion carbon fiber frame and has demonstrated that the three BPMs behave as a rigid-body to less than 5 nm. To date, we have demonstrated a BPM resolution of less than 20 nm over a dynamic range of ± 20 microns.