Gronberg, J.

Paper	Title	Page
WEOCAB01	Design of the Beam Delivery System for the International Linear Collider	1985
	A. Seryi I. V. Agapov, G. A. Blair, S. T. Boogert, J. Carter Royal Holloway, University of London, Surrey M. Alabau, P. Bambade, J. Brossard, O. Dadoun LAL, Orsay J. A. Amann, R. Arnold, F. Asiri, K. L.F. Bane, P. Bellomo, E. Doyle, A. F. Fasso, L. Keller, J. Kim, K. Ko, Z. Li, T. W. Markiewicz, T. V.M. Maruyama, K. C. Moffeit, S. Molloy, Y. Nosochkov, N. Phinney, T. O. Raubenheimer, S. Seletskiy, S. Smith, C. M. Spencer, P. Tenenbaum, D. R. Walz, G. R. White, M. Woodley, M. Woods, L. Xiao SLAC, Menlo Park, California M. Anerella, A. K. Jain, A. Marone, B. Parker BNL, Upton, Long Island, New York D. A.-K. Angal-Kalinin, C. D. Beard, J.-L. Fernandez-Hernando, P. Goudket, F. Jackson, J. K. Jones, A. Kalinin, P. A. McIntosh STFC/DL/ASTeC, Daresbury, Warrington, Cheshire R. Appleby UMAN, Manchester J. L. Baldy, D. Schulte CERN, Geneva L. Bellantoni, A. I. Drozhdin, V. S. Kashikhin, V. Kuchler, T. Lackowski, N. V. Mokhov, N. Nakao, T. Peterson, M. C. Ross, S. I. Striganov, J. C. Tompkins, M. Wendt, X. Yang Fermilab, Batavia, Illinois K. Buesser DESY, Hamburg P. Burrows, G. B. Christian, C. I. Clarke, A. F. Hartin OXFORDphysics, Oxford, Oxon G. Burt, A. C. Dexter Cockcroft Institute, Warrington, Cheshire J. Carwardine, C. W. Saunders ANL, Argonne, Illinois B. Constance, H. Dabiri Khah, C. Perry, C. Swinson JAI, Oxford O. Delferriere, O. Napoly, J. Payet, D. Uriot CEA, Gif-sur-Yvette C. J. Densham, R. J.S. Greenhalgh STFC/RAL, Chilton, Didcot, Oxon A. Enomoto, S. Kuroda, T. Okugi, T. Sanami, Y. Suetsugu, T. Tauchi KEK, Ibaraki A. Ferrari UU/ISV, Uppsala J. Gronberg LLNL, Livermore, California Y. Iwashita Kyoto ICR, Uji, Kyoto W. Lohmann DESY Zeuthen, Zeuthen L. Ma STFC/DL, Daresbury, Warrington, Cheshire T. M. Mattison UBC, Vancouver, B. C. T. S. Sanuki University of Tokyo, Tokyo V. I. Telnov BINP SB RAS, Novosibirsk E. T. Torrence University of Oregon, Eugene, Oregon D. Warner Colorado University at Boulder, Boulder, Colorado N. K. Watson Birmingham University, Birmingham H. Y. Yamamoto Tohoku University, Sendai
	The beam delivery system for the linear collider focuses beams to nanometer sizes at the interaction point, collimates the beam halo to provide acceptable background in the detector and has a provision for state-of-the art beam instrumentation in order to reach the physics goals. The beam delivery system of the International Linear Collider has undergone several configuration changes recently. This paper describes the design details and status of the baseline configuration considered for the reference design.
	Slides
FRPMS049	Resolution of a High Performance Cavity Beam Position Monitor System	4090
	S. Walston S. T. Boogert Royal Holloway, University of London, Surrey C. C. Chung, P. Fitsos, J. Gronberg LLNL, Livermore, California J. C. Frisch, S. Hinton, J. May, D. J. McCormick, S. Smith, T. J. Smith, G. R. White SLAC, Menlo Park, California H. Hayano, Y. Honda, N. Terunuma, J. Urakawa KEK, Ibaraki Yu. G. Kolomensky, T. Orimoto UCB, Berkeley, California P. Loscutoff LBNL, Berkeley, California A. Lyapin, S. Malton, D. J. Miller UCL, London R. Meller Cornell University, Department of Physics, Ithaca, New York M. C. Ross Fermilab, Batavia, Illinois M. Slater, M. Thomson, D. R. Ward University of Cambridge, Cambridge V. Vogel DESY, Hamburg
	International Linear Collider (ILC) interaction region beam sizes and component position stability requirements will be as small as a few nanometers. It is important to the ILC design effort to demonstrate that these tolerances can be achieved – ideally using beam-based stability measurements. It has been estimated that RF cavity beam position monitors (BPMs) could provide position measurement resolutions of less than one nanometer and could form the basis of the desired beam-based stability measurement. We have developed a high resolution RF cavity BPM system. A triplet of these BPMs has been installed in the extraction line of the KEK Accelerator Test Facility (ATF) for testing with its ultra-low emittance beam. A metrology system for the three BPMs was recently installed. This system employed optical encoders to measure each BPM's position and orientation relative to a zero-coefficient of thermal expansion carbon fiber frame and has demonstrated that the three BPMs behave as a rigid-body to less than 5 nm. To date, we have demonstrated a BPM resolution of less than 20 nm over a dynamic range of ± 20 microns.