A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z    

Jimenez, J.M.

Paper Title Page
WPAE020 A Large Diameter Entrance Window for the LHC Beam Dump Line 1698
 
  • A. Presland, B. Goddard, J.M. Jimenez, D.R. Ramos, R. Veness
    CERN, Geneva
  
  The graphite LHC beam dump block TDE has to absorb the full LHC beam intensity at 7 TeV. The TDE vessel will be filled with inert gas at atmospheric pressure, and requires a large diameter entrance window for vacuum separation from the beam dumping transfer line. The swept LHC beam must traverse this window without damage for regular operation of the beam dump dilution system. For dilution failures, the entrance window must survive most of the accident cases, and must not fail catastrophically in the event of damage. The conceptual design of the entrance window is presented, together with the load conditions and performance criteria. The FLUKA energy deposition simulations and ANSYS stress calculations are described, and the results discussed.  
TPAP007 LHC Collimation: Design and Results from Prototyping and Beam Tests 1078
 
  • R.W. Assmann, O. Aberle, G. Arduini, A. Bertarelli, H.-H. Braun, M. Brugger, H. Burkhardt, S. Calatroni, F. Caspers, E. Chiaveri, A. Dallocchio, B. Dehning, A. Ferrari, M. Gasior, A. Grudiev, E.B. Holzer, J.-B. Jeanneret, J.M. Jimenez, Y. Kadi, R. Losito, M. Magistris, A.M. Masi, M. Mayer, E. Métral, R. Perret, C. Rathjen, S. Redaelli, G. Robert-Demolaize, S. Roesler, M. Santana-Leitner, D. Schulte, P. Sievers, E. Tsoulou, H. Vincke, V. Vlachoudis, J. Wenninger
    CERN, Geneva
  • I. Baishev, I.L. Kurochkin
    IHEP Protvino, Protvino, Moscow Region
  • G. Spiezia
    Naples University Federico II, Science and Technology Pole, Napoli
  
  The problem of collimation and beam cleaning concerns one of the most challenging aspects of the LHC project. A collimation system must be designed, built, installed and commissioned with parameters that extend the present state-of-the-art by 2-3 orders of magnitude. Problems include robustness, cleaning efficiency, impedance and operational aspects. A strong design effort has been performed at CERN over the last two years. The system design has now been finalized for the two cleaning insertions. The adopted phased approach is described and the expected collimation performance is discussed. In parallel robust and precisely controllable collimators have been designed. Several LHC prototype collimators have been built and tested with the highest beam intensities that are presently available at CERN. The successful beam tests are presented, including beam-based setup procedures, a 2 MJ robustness test and measurements of the collimator-induced impedance. Finally, an outlook is presented on the challenges that are ahead in the coming years.  
RPPE042 Aperture and Field Constraints for the Vacuum System in the LHC Injection Septa 2732
 
  • M. Gyr, B. Henrist, J.M. Jimenez, J.-M. Lacroix, S. Sgobba
    CERN, Geneva
  
  Each beam arriving from the SPS has to pass through five injection septum magnets before being kicked onto the LHC orbit. The injection layout implies that the vacuum chambers for the two circulating beams pass through the septum magnet yokes at a flange distance from the chamber of the beam to be injected. Specially designed vacuum chambers and interconnections provide the required straightness and alignment precision, thus optimising the aperture for both the circulating and injected beams, without affecting the quality of the magnetic dipole field seen by the injected beam. The circulating beams are shielded against the magnetic stray field by using μ-metal chambers with a thickness of 0.9 mm to avoid saturation of the μ-metal (0.8 T), coated with copper (0.4 mm) for impedance reasons and NEG for pumping and electron cloud purposes. A sufficiently large gap between the iron yoke and the μ-metal chamber allows an in-situ bake-out at 200°C, based on a polyimide/stainless steel/polyimide sandwich structure with an overall thickness of 0.2 mm. The constraints will be described and the resulting vacuum system design, the apertures and the residual stray field will be presented.  
FPAP014 Electron Cloud Measurements in the SPS in 2004 1371
 
  • D. Schulte, G. Arduini, V. Baglin, J.M. Jimenez, F. Zimmermann
    CERN, Geneva
  
  Novel measurements of the electron cloud have been performed in the SPS in 2004. In this machine the beam consists of a number of short bunch trains. By varying the distance between these trains it is possible to witness the survival of the electrons after the bunch passage. In this paper, results from simulations and experiments are compared.