PAC 2005 - List of Authors

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Dedyk, A.

Paper	Title	Page
WPAT095	Low-Loss Ferroelectric for Accelerator Application	4305
	A. Kanareykin Euclid TechLabs, LLC, Solon, Ohio A. Dedyk, S.F. Karmanenko Eltech University, St. Petersburg E. Nenasheva Ceramics Ltd., St. Petersburg V.P. Yakovlev Omega-P, Inc., New Haven, Connecticut
	Funding: U.S. Department of Energy. Ferroelectric ceramics have an electric field-dependent dielectric permittivity that can be altered by applying a bias voltage. Ferroelectrics have unique intrinsic properties that makes them attractive for high-energy accelerator applications: very small response time of ~ 10^-11 sec, considerably high breakdown limit of more than 100 kV/cm, good vacuum properties. Because of these features, bulk ferroelectrics may be used as active elements of tunable accelerator structures,* or in fast, electrically - controlled switches and phase shifters in pulse compressors or power distribution circuits of future linear colliders.** One of the most critical requirements for ferroelectric ceramic in these applications is the dielectric loss factor. In this paper, the new bulk ferroelectric ceramic is presented. The new composition shows a loss tangent of 4× 10^-3 at 35 GHz. The ceramics have high tunability factor: the bias voltage of 50 kV/cm was enough to reduce the permittivity from 500 to 400. The material chemical compound, features of the technology process, and mechanical and electrical properties are discussed. The ways of BST ferrolectric parameters further improvement are discussed as well. A. Kanareykin, W. Gai, J. Power, E. Sheinman, and A. Altmark, AIP Conf. Proc. 647, Melville, N.Y., 2002, p. 565. *V.P. Yakovlev, O.A. Nezhevenko, J.L. Hirshfield, and A.D. Kanareykin, AIP Conf. Proc. 691, Melville, N.Y., 2003, p.187.

Paper

Title

Page

WPAT095

Low-Loss Ferroelectric for Accelerator Application

4305

A. Kanareykin
Euclid TechLabs, LLC, Solon, Ohio
A. Dedyk, S.F. Karmanenko
Eltech University, St. Petersburg
E. Nenasheva
Ceramics Ltd., St. Petersburg
V.P. Yakovlev
Omega-P, Inc., New Haven, Connecticut

Funding: U.S. Department of Energy.

Ferroelectric ceramics have an electric field-dependent dielectric permittivity that can be altered by applying a bias voltage. Ferroelectrics have unique intrinsic properties that makes them attractive for high-energy accelerator applications: very small response time of ~ 10^-11 sec, considerably high breakdown limit of more than 100 kV/cm, good vacuum properties. Because of these features, bulk ferroelectrics may be used as active elements of tunable accelerator structures,* or in fast, electrically - controlled switches and phase shifters in pulse compressors or power distribution circuits of future linear colliders.** One of the most critical requirements for ferroelectric ceramic in these applications is the dielectric loss factor. In this paper, the new bulk ferroelectric ceramic is presented. The new composition shows a loss tangent of 4× 10^-3 at 35 GHz. The ceramics have high tunability factor: the bias voltage of 50 kV/cm was enough to reduce the permittivity from 500 to 400. The material chemical compound, features of the technology process, and mechanical and electrical properties are discussed. The ways of BST ferrolectric parameters further improvement are discussed as well.

*A. Kanareykin, W. Gai, J. Power, E. Sheinman, and A. Altmark, AIP Conf. Proc. 647, Melville, N.Y., 2002, p. 565. **V.P. Yakovlev, O.A. Nezhevenko, J.L. Hirshfield, and A.D. Kanareykin, AIP Conf. Proc. 691, Melville, N.Y., 2003, p.187.