| Paper | Title | Page |
|---|---|---|
| MOPA007 | Polarized Proton Collisions at RHIC | 600 |
|
||
|
Funding: The work was performed under the auspices of the U.S. Department of Energy and RIKEN Japan. The Relativistic Heavy Ion Collider~(RHIC) provides not only collisions of ions but also collisions of polarized protons. In a circular accelerator, the polarization of polarized proton beam can be partially or fully lost when a spin depolarizing resonance is encountered. To preserve the beam polarization during acceleration, two full Siberian snakes were employed in RHIC to avoid depolarizing resonances. In 2003, polarized proton beams were accelerated to 100~GeV and collided in RHIC. Beams were brought into collisions with longitudinal polarization at the experiments STAR and PHENIX by using spin rotators. RHIC polarized proton run experience demonstrates that optimizing polarization transmission efficiency and improving luminosity performance are significant challenges. Currently, the luminosity lifetime in RHIC is limited by the beam-beam effect. The current state of RHIC polarized proton program, including its dedicated physics run in 2005 and efforts to optimize luminosity production in beam-beam limited conditions are reported. |
||
| TOAC003 | Stochastic Cooling for Bunched Beams | 310 |
|
||
|
Funding: Work performed under the auspices of the U.S. DOE. A longitudinal stochastic cooling system for RHIC is under construction and partial commissioning is planned for the upcoming run. The state of the system and future plans are discussed. |
||
| TPAP043 | Electron Cooling of RHIC | 2741 |
|
||
|
We report progress on the R&D program for electron-cooling of the Relativistic Heavy Ion Collider (RHIC). This electron cooler is designed to cool 100 GeV/nucleon at storage energy using 54 MeV electrons. The electron source will be a superconducting RF photocathode gun. The accelerator will be a superconducting energy recovery linac. The frequency of the accelerator is set at 703.75 MHz. The maximum electron bunch frequency is 9.38 MHz, with bunch charge of 20 nC. The R&D program has the following components: The photoinjector and its photocathode, the superconducting linac cavity, start-to-end beam dynamics with magnetized electrons, electron cooling calculations including benchmarking experiments and development of a large superconducting solenoid. The photoinjector and linac cavity are being incorporated into an energy recovery linac aimed at demonstrating ampere class current at about 20 MeV. A Zeroth Order Design Report is in an advanced draft state, and can be found on the web at http://www.agsrhichome.bnl.gov/eCool/.
Under contract with the U.S. Department of Energy, Contract Number DE-AC02-98CH10886. |
||
| TPAT081 | Observation of Electron-Ion Effects at RHIC Transition | 4087 |
|
||
|
Funding: Work performed under the auspices of the U.S. Department of Energy. Electron cloud is found to be a serious obstacle on the upgrade path of the Relativistic Heavy Ion Collider (RHIC). At twice the design number of bunches, electron-ion interactions cause significant instability, emittance growth, and beam loss along with vacuum pressure rises when the beam is accelerated across the transition. |
||
| TPAT093 | Operations and Performance of RHIC as a Cu-Cu Collider | 4281 |
|
||
|
Funding: Work performed under the auspices of the U.S. Department of Energy. The 5th year of RHIC operations, started in November 2004 and expected to last till June 2005, consists of a physics run with Cu-Cu collisions at 100 GeV/u followed by one with polarized protons at 100 GeV. We will address here overall performance of the RHIC complex used for the first time as a Cu-Cu collider, and compare it with previous operational experience with Au, PP and asymmetric d-Au collisions. We will also discuss operational improvements, such as a ?* squeeze to 85cm in the high luminosity interaction regions from the design value of 1m, system improvements and machine performance limitations, such as vacuum pressure rise, intra-beam scattering, and beam beam interaction. |
||
| TPAT095 | Beam Induced Pressure Rise at RHIC | 4308 |
|
||
|
Beam induced pressure rise in RHIC warm sections is currently one of the machine intensity and luminosity limits. This pressure rise is mainly due to electron cloud effects. The RHIC warm section electron cloud is associated with longer bunch spacings compared with other machines, and is distributed non-uniformly around the ring. In addition to the countermeasures for normal electron cloud, such as the NEG coated pipe, solenoids, beam scrubbing, bunch gaps, and larger bunch spacing, other studies and beam tests toward the understanding and counteracting RHIC warm electron cloud are of interest. These include the ion desorption studies and the test of anti-grazing ridges. For high bunch intensities and the shortest bunch spacings, pressure rises at certain locations in the cryogenic region have been observed during the past two runs. Beam studies are planned for the current 2005 run and the results will be reported.
Work performed under the auspices of the US Department of Energy. |
||
| TPPP019 | Collective Effects in Lepton Ring of eRHIC | 1628 |
|
||
|
Funding: Department of Energy. The eRHIC is a new generation lepton-hadron collider undergoing design studies by a collaboration of BNL, MIT, DESY and BINP. The collider complex will consist of a hadron machine that is mainly the existing RHIC with necessary upgrades, and a new lepton machine that can provide intense, highly polarized electron and positron beams at energy of 5-10 GeV. The ring-ring option of eRHIC is to build a 5-10 GeV electron ring with a injector chain. In this paper the beam lifetime of lepton beams is calculated. |
||
| TPPP043 | ERL Based Electron-Ion Collider eRHIC | 2768 |
|
||
|
Funding: Work performed under Contract Number DE-AC02-98CH10886 with the auspices of the US Department of Energy. We present the designs of a future polarized electron-hadron collider, eRHIC* based on a high current super-conducting energy-recovery linac (ERL) with energy of electrons up to 20 GeV. We plan to operate eRHIC in both dedicated (electron-hadrons only) and parallel(with the main hadron-hadron collisions) modes. The eRHIC has very large tunability range of c.m. energies while maintaining very high luminosity up to 1034 cm-2 s-1 per nucleon. Two of the most attractive features of this scheme are full spin transparency of the ERL at all operational energies and the capability to support up to four interaction points. We present two main layouts of the eRHIC, the expected beam and luminosity parameter, and discuss the potential limitation of its performance. *http://www.agsrhichome.bnl.gov/eRHIC/, Appendix A: Linac-Ring Option. |
||
| TPPT069 | Design Considerations for the Mechanical Tuner of the RHIC Electron Cooler SRF Cavity | 3786 |
|
||
|
Funding: Work is supported by the DOD Joint Technology Office and by the U.S. Department of Energy. The ECX Project, Brookhaven Lab's predecessor to the RHIC e-Cooler, includes a prototype RF tuner mechanism capable of both coarse and fine tuning of the superconducting RF cavity. This tuner is adapted originally from a DESY design concept but with a longer stroke and significantly higher loads due to our very stiff cavity shape. Structural design, kinematics, controls, thermal and RF issues are discussed and certain improvements are proposed. |
||
| RPPE009 | Extremely High Current, High-Brightness Energy Recovery Linac | 1150 |
|
||
|
Funding: Under contract with the U.S. Department of Energy, U.S. DOD Office of Naval Research and Joint Technology Office. Next generation ERL light-sources, high-energy electron coolers, high-power Free-Electron Lasers, powerful Compton X-ray sources and many other accelerators were made possible by the emerging technology of high-power, high-brightness electron beams. In order to get the anticipated performance level of ampere-class currents, many technological barriers are yet to be broken. BNL’s Collider-Accelerator Department is pursuing some of these technologies for its electron cooling of RHIC application, as well as a possible future electron-hadron collider. We will describe work on CW, high-current and high-brightness electron beams. This will include a description of a superconducting, laser-photocathode RF gun and an accelerator cavity capable of producing low emittance (about 1 micron rms normalized) one nano-Coulomb bunches at currents of the order of one ampere average. |
||
| RPPE048 | Physical and Electromagnetic Properties of Customized Coatings for SNS Injection Ceramic Chambers and Extraction Ferrite Kickers | 3028 |
|
||
|
Funding: SNS is managed by UT-Battelle, LLC, under contract DE-AC05-00OR22725 for the U.S. Department of Energy. SNS is a partnership of six national laboratories: Argonne, Brookhaven, Jefferson, Lawrence Berkeley, Los Alamos, and Oak Ridge. The inner surfaces of the 248 m SNS accumulator ring vacuum chambers are coated with ~100 nm of titanium nitride (TiN) to reduce the secondary electron yield (SEY) of the chamber walls. All the ring inner surfaces are made of stainless or inconel, except those of the injection and extraction kickers. Ceramic vacuum chambers are used for the 8 injection kickers to avoid shielding of a fast-changing kicker field and to reduce eddy current heating. The internal diameter was coated with Cu to reduce the beam coupling impedance and provide passage for beam image current, and a TiN overlayer to reduce SEY. The ferrite surfaces of the 14 extraction kicker modules were coated with TiN to reduce SEY. Customized masks were used to produce coating strips of 1 cm x 5 cm with 1 to 1.5 mm separation among the strips. The masks maximized the coated area to more than 80%, while minimizing the eddy current effect to the kicker rise time. The coating method, as well as the physical and electromagnetic properties of the coatings for both types of kickers will be summarized, with emphasis on the effect to the beam and the electron cloud buildup. †Corresponding author email: hseuh@bnl.gov. |
||
| RPPT032 | High Current Energy Recovery Linac at BNL | 2242 |
|
||
|
Funding: Work performed under Contract Number DE-AC02-98CH10886 with the auspices of the U.S. Department of Energy. We present the design and the parameters of a small Energy Recovery Linac (ERL) facility, which is under construction at BNL. This R&D facility has goals to demonstrate CW operation of ERL with average beam current in the range of 0.1 - 1 ampere, combined with very high efficiency of energy recovery. The possibility for future up-grade to a two-pass ERL is being considered. The heart of the facility is a 5-cell 703.75 MHz super-conducting RF linac with HOM damping. Flexible lattice of ERL provides a test-bed for testing issues of transverse and longitudinal instabilities and diagnostics of intense CW e-beam. We present the status and plans for this facility. |
||
| FPAE029 | Setup and Performance of the RHIC Injector Accelerators for the 2005 Run with Copper Ions | 2068 |
|
||
|
Funding: Work performed under the auspices of the U.S. Department of Energy. Copper ions for the 2005 run of the Relativistic Heavy Ion Collider (RHIC) at Brookhaven National Laboratory are accelerated in the Tandem, Booster and AGS prior to injection into RHIC. The setup and performance of this chain of accelerators will be reviewed. |