NAPAC2016 - List of Authors (Hasse, Q.B.)

Paper	Title	Page
THA1CO05	Thermal Modeling and Cryogenic Design of a Helical Superconducting Undulator Cryostat	1064
	Y. Shiroyanagi, J.D. Fuerst, Q.B. Hasse, Y. Ivanyushenkov ANL, Argonne, Illinois, USA
	A conceptual design for a helical superconducting undulator (HSCU) for the Advanced Photon Source (APS) at Argonne National Laboratory (ANL) has been completed. The device differs sufficiently from the existing APS planar superconducting undulator (SCU) design to warrant development of a new cryostat based on value engineering and lessons learned from the existing planar SCU. Changes include optimization of the existing cryocooler-based refrigeration system and thermal shield as well as cost reduction through the use of standard vacuum hardware. The end result is a design that provides significantly larger 4.2 K refrigeration margin in a smaller package for greater installation flexibility in the APS storage ring. This paper presents ANSYS-based thermal analysis of the cryostat, including estimated static and dynamic (beam-induced) heating, and compares the new design with the existing planar SCU cryostat. Work supported by the U.S. Department of Energy, Office of Science, under Contract No. DE-AC02-06CH11357.
	Slides THA1CO05 [3.905 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2016-THA1CO05
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THA1CO06	Status of the Development of Superconducting Undulators for Storage Rings and Free Electron Lasers at the Advanced Photon Source	1068
	Y. Ivanyushenkov, C.L. Doose, J.F. Fuerst, E. Gluskin, K.C. Harkay, Q.B. Hasse, M. Kasa, Y. Shiroyanagi, D. Skiadopoulos, E. Trakhtenberg ANL, Argonne, Illinois, USA P. Emma SLAC, Menlo Park, California, USA
	Funding: Work supported by the U.S. Department of Energy, Office of Science, under Contract No. DE-AC02-06CH11357. Development of superconducting undulator (SCU) technology continues at the Advanced Photon Source (APS). Experience of building and successful operation of the first short-length, 16-mm period length superconducting undulator SCU0 paved a way for the second 1-m long, 18-mm period device, SCU1, which is in operation since May 2015. The APS SCU team has also built and tested a 1.5-m long, 21-mm period undulator as a part of LCLS SCU R&D program aiming at demonstration of SCU technology availability for free electron lasers. This undulator successfully achieved all the requirements including a phase error of 5 degree rms. Our team is currently completing one more 1-m, 18-mm period undulator that will replace the SCU0. We are also working on a helical SCU for the APS. The status of these projects will be presented.
	Slides THA1CO06 [3.545 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2016-THA1CO06
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Thermal Modeling and Cryogenic Design of a Helical Superconducting Undulator Cryostat

1064

Y. Shiroyanagi, J.D. Fuerst, Q.B. Hasse, Y. Ivanyushenkov
ANL, Argonne, Illinois, USA

A conceptual design for a helical superconducting undulator (HSCU) for the Advanced Photon Source (APS) at Argonne National Laboratory (ANL) has been completed. The device differs sufficiently from the existing APS planar superconducting undulator (SCU) design to warrant development of a new cryostat based on value engineering and lessons learned from the existing planar SCU. Changes include optimization of the existing cryocooler-based refrigeration system and thermal shield as well as cost reduction through the use of standard vacuum hardware. The end result is a design that provides significantly larger 4.2 K refrigeration margin in a smaller package for greater installation flexibility in the APS storage ring. This paper presents ANSYS-based thermal analysis of the cryostat, including estimated static and dynamic (beam-induced) heating, and compares the new design with the existing planar SCU cryostat.
Work supported by the U.S. Department of Energy, Office of Science, under Contract No. DE-AC02-06CH11357.

Slides THA1CO05 [3.905 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2016-THA1CO05

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THA1CO06

Status of the Development of Superconducting Undulators for Storage Rings and Free Electron Lasers at the Advanced Photon Source

1068

Y. Ivanyushenkov, C.L. Doose, J.F. Fuerst, E. Gluskin, K.C. Harkay, Q.B. Hasse, M. Kasa, Y. Shiroyanagi, D. Skiadopoulos, E. Trakhtenberg
ANL, Argonne, Illinois, USA
P. Emma
SLAC, Menlo Park, California, USA

Funding: Work supported by the U.S. Department of Energy, Office of Science, under Contract No. DE-AC02-06CH11357.
Development of superconducting undulator (SCU) technology continues at the Advanced Photon Source (APS). Experience of building and successful operation of the first short-length, 16-mm period length superconducting undulator SCU0 paved a way for the second 1-m long, 18-mm period device, SCU1, which is in operation since May 2015. The APS SCU team has also built and tested a 1.5-m long, 21-mm period undulator as a part of LCLS SCU R&D program aiming at demonstration of SCU technology availability for free electron lasers. This undulator successfully achieved all the requirements including a phase error of 5 degree rms. Our team is currently completing one more 1-m, 18-mm period undulator that will replace the SCU0. We are also working on a helical SCU for the APS. The status of these projects will be presented.

Slides THA1CO06 [3.545 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2016-THA1CO06

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)