NAPAC2016 - List of Authors (Hartsell, B.D.)

Paper	Title	Page
MOPOB14	Experimental Results of Beryllium Exposed to Intense High Energy Proton Beam Pulses	102
	K. Ammigan, B.D. Hartsell, P. Hurh, R.M. Zwaska Fermilab, Batavia, Illinois, USA A.R. Atherton STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom M.E.J. Butcher, M. Calviani, M. Guinchard, R. Losito CERN, Geneva, Switzerland O. Caretta, T.R. Davenne, C.J. Densham, M.D. Fitton, P. Loveridge, J. O'Dell STFC/RAL, Chilton, Didcot, Oxon, United Kingdom V.I. Kuksenko, S.G. Roberts University of Oxford, Oxford, United Kingdom S.G. Roberts CCFE, Abingdon, Oxon, United Kingdom
	Funding: Work supported by Fermi Research Alliance, LLC, under Contract No. DE-AC02-07CH11359 with the U.S. Department of Energy. Beryllium is extensively used in various accelerator beam lines and target facilities as material for beam windows, and to a lesser extent, as secondary particle production targets. With increasing beam intensities of future accelerator facilities, it is critical to understand the response of beryllium under extreme conditions to reliably operate these components as well as avoid compromising particle production efficiency by limiting beam parameters. As a result, an exploratory experiment at CERN's HiRadMat facility was carried out to take advantage of the test facility's tunable high intensity proton beam to probe and investigate the damage mechanisms of several beryllium grades. The test matrix consisted of multiple arrays of thin discs of varying thicknesses as well as cylinders, each exposed to increasing beam intensities. This paper outlines the experimental measurements, as well as findings from Post-Irradiation-Examination (PIE) work where different imaging techniques were used to analyze and compare surface evolution and microstructural response of the test matrix specimens.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2016-MOPOB14
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPOB35	Design of the LBNF Beamline Target Station	146
	S. Tariq, K. Ammigan, K. Anderson, S.A. Buccellato, C.F. Crowley, B.D. Hartsell, P. Hurh, J. Hylen, P.H. Kasper, G.E. Krafczyk, A. Lee, B.G. Lundberg, A. Marchionni, N.V. Mokhov, C.D. Moore, V. Papadimitriou, D. Pushka, I.L. Rakhno, S.D. Reitzner, V.I. Sidorov, A.M. Stefanik, I.S. Tropin, K. Vaziri, K.E. Williams, R.M. Zwaska Fermilab, Batavia, Illinois, USA C.J. Densham STFC/RAL, Chilton, Didcot, Oxon, United Kingdom
	Funding: Work supported by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy. The Long Baseline Neutrino Facility (LBNF) project will build a beamline located at Fermilab to create and aim an intense neutrino beam of appropriate energy range toward the DUNE detectors at the SURF facility in Lead, South Dakota. Neutrino production starts in the Target Station, which consists of a solid target, magnetic focusing horns, and the associated sub-systems and shielding infrastructure. Protons hit the target producing mesons which are then focused by the horns into a helium-filled decay pipe where they decay into muons and neutrinos. The target and horns are encased in actively cooled steel and concrete shielding in a chamber called the target chase. The reference design chase is filled with air, but nitrogen and helium are being evaluated as alternatives. A replaceable beam window separates the decay pipe from the target chase. The facility is designed for initial operation at 1.2 MW, with the ability to upgrade to 2.4 MW, and is taking advantage of the experience gained by operating Fermilab's NuMI facility. We discuss here the design status, associated challenges, and ongoing R&D and physics-driven component optimization of the Target Station.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2016-MOPOB35
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPOA15	Installation Progress at the PIP-II Injector Test at Fermilab	722
	C.M. Baffes, M.L. Alvarez, R. Andrews, A.Z. Chen, J. Czajkowski, P. Derwent, J.P. Edelen, B.M. Hanna, B.D. Hartsell, K.R. Kendziora, D.V. Mitchell, L.R. Prost, V.E. Scarpine, A.V. Shemyakin, J. Steimel, T.J. Zuchnik Fermilab, Batavia, Illinois, USA A.L. Edelen CSU, Fort Collins, Colorado, USA
	Funding: Fermilab is operated by Fermi Research Alliance, LLC under Contract No. De-AC02-07CH11359 with the United States Department of Energy A CW-compatible, pulsed H⁻ superconducting linac 'PIP-II' is being planned to upgrade Fermilab's injection complex. To validate the concept of the front-end of such a machine, a test accelerator (The PIP-II Injector Test, formerly known as "PXIE") is under construction. The warm part of this accelerator comprises a 10 mA DC 30 keV H⁻ ion source, a 2m-long LEBT, a 2.1 MeV CW RFQ, and a 10-m long MEBT that is capable of creating a large variety of bunch structures. The paper will report on the installation of the RFQ and the first sections of the MEBT and related mechanical design considerations.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2016-WEPOA15
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Experimental Results of Beryllium Exposed to Intense High Energy Proton Beam Pulses

102

K. Ammigan, B.D. Hartsell, P. Hurh, R.M. Zwaska
Fermilab, Batavia, Illinois, USA
A.R. Atherton
STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom
M.E.J. Butcher, M. Calviani, M. Guinchard, R. Losito
CERN, Geneva, Switzerland
O. Caretta, T.R. Davenne, C.J. Densham, M.D. Fitton, P. Loveridge, J. O'Dell
STFC/RAL, Chilton, Didcot, Oxon, United Kingdom
V.I. Kuksenko, S.G. Roberts
University of Oxford, Oxford, United Kingdom
S.G. Roberts
CCFE, Abingdon, Oxon, United Kingdom

Funding: Work supported by Fermi Research Alliance, LLC, under Contract No. DE-AC02-07CH11359 with the U.S. Department of Energy.
Beryllium is extensively used in various accelerator beam lines and target facilities as material for beam windows, and to a lesser extent, as secondary particle production targets. With increasing beam intensities of future accelerator facilities, it is critical to understand the response of beryllium under extreme conditions to reliably operate these components as well as avoid compromising particle production efficiency by limiting beam parameters. As a result, an exploratory experiment at CERN's HiRadMat facility was carried out to take advantage of the test facility's tunable high intensity proton beam to probe and investigate the damage mechanisms of several beryllium grades. The test matrix consisted of multiple arrays of thin discs of varying thicknesses as well as cylinders, each exposed to increasing beam intensities. This paper outlines the experimental measurements, as well as findings from Post-Irradiation-Examination (PIE) work where different imaging techniques were used to analyze and compare surface evolution and microstructural response of the test matrix specimens.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2016-MOPOB14

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPOB35

Design of the LBNF Beamline Target Station

146

S. Tariq, K. Ammigan, K. Anderson, S.A. Buccellato, C.F. Crowley, B.D. Hartsell, P. Hurh, J. Hylen, P.H. Kasper, G.E. Krafczyk, A. Lee, B.G. Lundberg, A. Marchionni, N.V. Mokhov, C.D. Moore, V. Papadimitriou, D. Pushka, I.L. Rakhno, S.D. Reitzner, V.I. Sidorov, A.M. Stefanik, I.S. Tropin, K. Vaziri, K.E. Williams, R.M. Zwaska
Fermilab, Batavia, Illinois, USA
C.J. Densham
STFC/RAL, Chilton, Didcot, Oxon, United Kingdom

Funding: Work supported by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy.
The Long Baseline Neutrino Facility (LBNF) project will build a beamline located at Fermilab to create and aim an intense neutrino beam of appropriate energy range toward the DUNE detectors at the SURF facility in Lead, South Dakota. Neutrino production starts in the Target Station, which consists of a solid target, magnetic focusing horns, and the associated sub-systems and shielding infrastructure. Protons hit the target producing mesons which are then focused by the horns into a helium-filled decay pipe where they decay into muons and neutrinos. The target and horns are encased in actively cooled steel and concrete shielding in a chamber called the target chase. The reference design chase is filled with air, but nitrogen and helium are being evaluated as alternatives. A replaceable beam window separates the decay pipe from the target chase. The facility is designed for initial operation at 1.2 MW, with the ability to upgrade to 2.4 MW, and is taking advantage of the experience gained by operating Fermilab's NuMI facility. We discuss here the design status, associated challenges, and ongoing R&D and physics-driven component optimization of the Target Station.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2016-MOPOB35

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPOA15

Installation Progress at the PIP-II Injector Test at Fermilab

722

C.M. Baffes, M.L. Alvarez, R. Andrews, A.Z. Chen, J. Czajkowski, P. Derwent, J.P. Edelen, B.M. Hanna, B.D. Hartsell, K.R. Kendziora, D.V. Mitchell, L.R. Prost, V.E. Scarpine, A.V. Shemyakin, J. Steimel, T.J. Zuchnik
Fermilab, Batavia, Illinois, USA
A.L. Edelen
CSU, Fort Collins, Colorado, USA

Funding: Fermilab is operated by Fermi Research Alliance, LLC under Contract No. De-AC02-07CH11359 with the United States Department of Energy
A CW-compatible, pulsed H⁻ superconducting linac 'PIP-II' is being planned to upgrade Fermilab's injection complex. To validate the concept of the front-end of such a machine, a test accelerator (The PIP-II Injector Test, formerly known as "PXIE") is under construction. The warm part of this accelerator comprises a 10 mA DC 30 keV H⁻ ion source, a 2m-long LEBT, a 2.1 MeV CW RFQ, and a 10-m long MEBT that is capable of creating a large variety of bunch structures. The paper will report on the installation of the RFQ and the first sections of the MEBT and related mechanical design considerations.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2016-WEPOA15

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)