Paper | Title | Other Keywords | Page |
---|---|---|---|
MOPO061 | Beam Parameters Measurement of C-band 6 MeV Linear Electron Accelerator | gun, electron, controls, klystron | 133 |
|
|||
The new linear electron accelerator with beam energy varied in the range of 2-6 MeV with dual-energy option has been designed by Laboratory of Electron Accelerators MSU Ltd. Linac is based on compact high gradient stand-ing wave C-band accelerating structure fed by multi-beam klystron and is used in the cargo inspection and cancer therapy complexes. In the report, we present the results of electron beam parameters measurements at special stand. | |||
DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2018-MOPO061 | ||
About • | paper received ※ 10 September 2018 paper accepted ※ 19 September 2018 issue date ※ 18 January 2019 | ||
Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
MOPO080 | The Manufacturing of the CSNS DTL Tank | cavity, DTL, vacuum, linac | 167 |
|
|||
The DTL tank is a crucial component of the China Spallation Neutron Source (CSNS) linear accelerator (LINAC), which mainly use the technology of oxygen-free copper (OFC) electroplating on the inner surface of the 20# carbon steel tube. It is the first time to perform OFC electroplating with high electrical conductivity in the high intensity beam accelerator in China. In the process of cavity manufacturing, problems such as machining deformation, plating surface nodule and plating peeling are encountered. In this project, based on pre-research and information from literature, the formula of acid solution was improved to construct a stable pickling process protocol. The manufacturing process of DTL tank and the measurement details are introduced in this paper. | |||
DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2018-MOPO080 | ||
About • | paper received ※ 10 September 2018 paper accepted ※ 20 September 2018 issue date ※ 18 January 2019 | ||
Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
MOPO095 | A Risk Based Approach to Improving Beam Availability at an Accelerator Facility | operation, experiment, GUI, proton | 207 |
|
|||
Funding: United States Department of Energy This paper describes a risk-based approach to improving beam availability at an accelerator facility. Los Alamos Neutron Science Center (LANSCE), like many other accelerator facilities, was built many years ago and has been re-purposed when new missions were adopted. Many of the upgrades to the accelerator and beamlines allowed improvements in the general area of the upgrade but large-scale, system-wide improvements were never accomplished. Because of this, the facility operates with a mix of old and new equipment of varying condition. Limited budgets have constrained spending for spares procurement making it vital to prioritize those items predicted to have the highest impact to availability, should they fail. A systematic approach is described where equipment is inventoried, condition assessed, rated for potential failure and finally compiled into a risk-based priority list. |
|||
![]() |
Poster MOPO095 [0.332 MB] | ||
DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2018-MOPO095 | ||
About • | paper received ※ 21 September 2018 paper accepted ※ 08 October 2018 issue date ※ 18 January 2019 | ||
Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||
THPO092 | LCLSII Fundamental Power Coupler Manufacturing Status and Lesson Learned | FEL, operation, SRF, status | 893 |
|
|||
Thales and RI Research Instrument have manufactured and assembled half of the power couplers for the LCLSII project. This paper remains main characteristics of these coupler. It will also describe main challenges that were overcome among them, thickness of copper coating on Warm Internal Conductor at 150µm and lessons learned during the manufacturing phase of these couplers. The paper will also propose some possible optimization for a future mass production of such components and parameters which could be relevant for a better understanding link to the statistic results obtained. | |||
DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2018-THPO092 | ||
About • | paper received ※ 10 September 2018 paper accepted ※ 21 September 2018 issue date ※ 18 January 2019 | ||
Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | ||