LINAC2018 - List of Authors (Schneider, P.P.)

Paper	Title	Page
THPO061	Beam Characterization of the MYRRHA-RFQ	830
SPWR017	use link to see paper's listing under its alternate paper code
	P.P. Schneider, M. Droba, O. Meusel, H. Podlech, A. Schempp IAP, Frankfurt am Main, Germany D. Noll CERN, Geneva, Switzerland
	Funding: This work is supported by the German Federal Ministry of Education and Research (BMBF) #05P15RFRBA and HORIZON 2020 for the MYRRHA project #662186 and HIC for FAIR. The Linear Accelerator for the MYRRHA project* is under construction. In a first step the linac up to 100 MeV will be realized. The LEBT section has been set into operation in Belgium and the RFQ is installed in summer 2018. A system to analyze the ion beam consisting of a slit-grid emittance scanner, a beam dump and a momentum spectrometer, called diagnostic train descripted in *, will be set on the rails to characterize the beam at the RFQ injection point. The results will be used to adjust the optimal matching for the RFQ. After the measurements downstream the LEBT, the diagnostic train begins its journey along the beam line and at the first station the RFQ is installed. The accelerated beam of the RFQ is then analyzed and optimized. In addition to optimization of transmission the artificial production of beam offsets in the LEBT is of special interest. These will be measured at the injection point to estimate the range of possible offsets. In the following measurements these offsets will be used to study the influence of the offsets on the RFQ performance. Furthermore, the RFQ parameters are varied to see their influence on the beam transport, transmission and beam quality. H.Aı̈t Abderrahim et al. "MYRRHA: A multipurpose accelerator driven system for research & development", 2001 ** 1st Experiments at the CW-Operated RFQ for Intense Proton Beams, LINAC16
	Poster THPO061 [4.610 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2018-THPO061
About •	paper received ※ 12 September 2018 paper accepted ※ 20 September 2018 issue date ※ 18 January 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

THPO061

Beam Characterization of the MYRRHA-RFQ

830

SPWR017

use link to see paper's listing under its alternate paper code

P.P. Schneider, M. Droba, O. Meusel, H. Podlech, A. Schempp
IAP, Frankfurt am Main, Germany
D. Noll
CERN, Geneva, Switzerland

Funding: This work is supported by the German Federal Ministry of Education and Research (BMBF) #05P15RFRBA and HORIZON 2020 for the MYRRHA project #662186 and HIC for FAIR.
The Linear Accelerator for the MYRRHA project* is under construction. In a first step the linac up to 100 MeV will be realized. The LEBT section has been set into operation in Belgium and the RFQ is installed in summer 2018. A system to analyze the ion beam consisting of a slit-grid emittance scanner, a beam dump and a momentum spectrometer, called diagnostic train descripted in **, will be set on the rails to characterize the beam at the RFQ injection point. The results will be used to adjust the optimal matching for the RFQ. After the measurements downstream the LEBT, the diagnostic train begins its journey along the beam line and at the first station the RFQ is installed. The accelerated beam of the RFQ is then analyzed and optimized. In addition to optimization of transmission the artificial production of beam offsets in the LEBT is of special interest. These will be measured at the injection point to estimate the range of possible offsets. In the following measurements these offsets will be used to study the influence of the offsets on the RFQ performance. Furthermore, the RFQ parameters are varied to see their influence on the beam transport, transmission and beam quality.
* H.Aı̈t Abderrahim et al. "MYRRHA: A multipurpose accelerator driven system for research & development", 2001
** 1st Experiments at the CW-Operated RFQ for Intense Proton Beams, LINAC16

Poster THPO061 [4.610 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-LINAC2018-THPO061

About •

paper received ※ 12 September 2018 paper accepted ※ 20 September 2018 issue date ※ 18 January 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)