| Paper |
Title |
Page |
| THPO102 |
Design Studies of Output Window for CEPC Klystron |
911 |
| |
- Z.J. Lu, Y.L. Chi, S. Fukuda, G. Pei, S. Pei, S.C. Wang, O. Xiao, U. N. Zaib, Z.S. Zhou
IHEP, Beijing, People’s Republic of China
- S. Fukuda
KEK, Ibaraki, Japan
|
|
| |
A high power and high efficiency klystron of the 650MHz, 800kW CW klystron for the Circular Electron Positron Collider (CEPC) is designed and developed at IHEP. This paper presents the design and simulation for the high power coaxial window for it. Plan of the hot test (high power testing before installing to the klystron) are also described. Simulation software of CST, ANSYS and Multipac 2.1 are used for design of window microwave structure, thermal analysis and multipacting effects. We obtained the good simulation results successively; the coaxial window S-parameter analysis, has revealed a low reflection at the operating frequency of 650 MHz. The thermal simulation shows a good temperature distribution under the cw 800kW propagation; maximum temperature has been found to be 33 °C at ceramic with water cooling in the inner and outer conductor. The multipacting at the window is possible source of the failure and it is shown that multipacting has less chance to be happened on the surface of ceramic.
|
|
| DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-LINAC2018-THPO102
|
|
| About • |
paper received ※ 12 September 2018 paper accepted ※ 31 October 2018 issue date ※ 18 January 2019 |
|
| Export • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
| |
| THPO095 |
Present Status of Capacitor-charging Power Supplies for Klystron Modulators in SuperKEKB Injector Linac |
898 |
| |
- M. Kawamura, M. Akemoto, S. Fukuda, H. Honma, S. Michizono, H. Nakajima, T. Natsui, T. Shidara
KEK, Ibaraki, Japan
- H. Akikawa, O. Endo, K. Sato
Nihon Koshuha Co. Ltd, Yokohama, Japan
|
|
| |
The capacitor-charging power supplies (CCPSs) for the klystron modulators have been developed from 2002 in the SuperKEKB injector linac. The specifications are that the output voltage is 43kV, the charging power is 30kJ/s, and the output voltage stability is 0.2%p-p. Being used in the old facility, their sizes are restricted in 480mm x 680 mm x 760mm. After various modifications, the 13 CCPSs in the linac have been operated with no fault since last October. The present status of the CCPSs, including the outlines, specifications, and the modifications against the faults, are described.
|
|
| DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-LINAC2018-THPO095
|
|
| About • |
paper received ※ 12 September 2018 paper accepted ※ 20 September 2018 issue date ※ 18 January 2019 |
|
| Export • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
| |
| THPO096 |
Design Study of a High Efficiency Klystron for SuperKEKB Linac |
901 |
| |
- F. Qiu, S. Fukuda, S. Matsumoto, T. Matsumoto, T. Miura, T. Natsui
KEK, Ibaraki, Japan
|
|
| |
The injector linear accelerator (linac) for the SuperKEKB particle accelerator requires a higher efficiency klystron than the currently used 50 MW, S-band, pulsed unit (PV3050/E3730), which operates at the same voltage, to increase the power redundancy. The efficiency is expected to improve from the currently observed 45% to more than 60%. We propose a type of high efficiency klystron using novel bunching mechanisms. The 1-D disk model based code is used for preliminary optimization of the tube parameters; these parameters are further checked by 2-D codes known as field charge interaction (FCI) and MAGIC. In this paper, the design consideration of the high efficiency klystron is presented.
|
|
| DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-LINAC2018-THPO096
|
|
| About • |
paper received ※ 12 September 2018 paper accepted ※ 20 September 2018 issue date ※ 18 January 2019 |
|
| Export • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
| |