| Paper | Title | Page |
|---|---|---|
| MOPMP002 | Linac and Damping Ring Designs for the FCC-ee | 420 |
|
||
| We report the design of the pre-injector chain for the Future Circular e+ e− Collider (FCC-ee) system. The electron beam from a low-emittance RF gun is accelerated by an S-band linac up to 6 GeV. A damping ring at 1.54 GeV is required for emittance cooling of the positron beam. The intermediate energy step from the exit of the S-band linac at 6 GeV to the 20 GeV injection energy of the top-up booster can be provided by the modified Super Proton Synchrotron (SPS), serving as a pre-booster ring (PBR). An alternative option to reach 20 GeV energy would be to extend the S-band linac with a C- or X-band linac. An overall cost optimisation will determine the choice of the final configuration. Beam loss and emittance dilution in the linac due to space charge effects, wakefields, and misalignment of accelerator components can be mitigated by RF phasing and orbit steering. Start-to-end simulations examine the beam transport through the linac up to either 6 GeV or 20 GeV. The results indicate large design margins. Simulations of the beam dynamics in the damping ring (DR) demonstrate a sufficiently large momentum acceptance. Effects of intrabeam scattering and electron cloud instability in the DR are also studied. | ||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-MOPMP002 | |
| About • | paper received ※ 13 May 2019 paper accepted ※ 21 May 2019 issue date ※ 21 June 2019 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| MOPTS032 | New Beam Dynamics Simulations for the FAIR p-Linac RFQ | 921 |
|
||
|
The construction of a 3.3m Ladder-RFQ at IAP*, Goethe University Frankfurt, has been finished successfully last summer. This RFQ is designed to accelerate protons from 95 keV to 3.0 MeV according to the design parameters of the p-Linac at FAIR**. Along the acceleration section the parameters modulation, aperture and synchronous phase are varied linearly with cell number, which differs from former designs from IAP Frankfurt. The ratio of transversal vane curvature radius to mid-cell radial aperture and the vane radius itself are constant. The development of an adequate beam dynamics design was done with the aid of the RFQGen-code and in close collaboration with the IAP resonator design team. The RFQ beam dynamics design could be successfully reproduced with the TOUTATIS-routine of CEAs*** TraceWin-code. Several new beam dynamics simulations were performed on the design. Among these were current and Twiss parameter studies as well as simulations concerned with the investigation of longitudinal entrance and exit gap field effects. Others were based on new measurements in the LEBT-line performed by the GSI**** Ion Source Group in April 2019. In the near future, further LEBT measurements and subsequent simulations (among other to design a well-fitting cone for the RFQ), as well as mechanical error studies in TOUTATIS, will follow.
*Institute of Applied Physics **Facility for Antiproton and Ion Research ***French Alternative Energies and Atomic Energy Commission ****GSI Helmholtz Centre for Heavy Ion Research |
||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-MOPTS032 | |
| About • | paper received ※ 14 May 2019 paper accepted ※ 20 May 2019 issue date ※ 21 June 2019 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| MOPTS065 | Alternative Design of CEPC LINAC | 1005 |
|
||
| Circular Electron-Positron Collider (CEPC) is a 100 km ring e+ e− collider for a Higgs factory. The injector is composed of a Linac and a Booster. The baseline design of CEPC Linac is a normal conducting S-band linear accelerator with frequency in 2860 MHz, which can provide electron and positron beam at an energy up to 10 GeV and bunch charge up to 3 nC. To reduce the design difficulty of booster and booster magnet at low energy part, an alternative design of the Linac with C-band accelerating structure at high energy part is proposed and the energy is up to 20 GeV. The compre-hensive consideration of Linac design and damping ring design will be discussed. In this paper, the physics design of this scheme is presented. | ||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-MOPTS065 | |
| About • | paper received ※ 16 May 2019 paper accepted ※ 19 May 2019 issue date ※ 21 June 2019 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |