Paper |
Title |
Page |
THPMB051 |
Development of Intelligent Alarm Message System at TPS |
3363 |
|
- C.C. Liang, C.H. Chang, C.H. Chen, J. Chen, J.Y. Chen, Y.-S. Cheng, M.-S. Chiu, S. Fann, C.S. Huang, C.-C. Kuo, T.Y. Lee, Y.C. Lin, Y.-C. Liu, H.-J. Tsai, F.H. Tseng, I.C. Yang, T.-C. Yu
NSRRC, Hsinchu, Taiwan
|
|
|
The traditional alarm systems usually set up/low limit for various signals. When the acquired values exceed the limits, the alarm system would be activated. The proposed system in this article can focus on various possible events with many kinds of signals for response judgments. During alarm calling period, data can also be announced and recorded. The system can also monitor various events according to different time shifts. Integrating LabVIEW, mobile phone, AT-command and Bluetooth communication, the system can handle factory broadcast, sending E-mail and SMS message. The above sound and words messages can be set directly at the home-made software interface. The new intelligent alarm system can eliminate the procedure made by man with the added event recording, system stability improvement and debugging function in wider application fields.
|
|
Export • |
reference for this paper to
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|
THPMY011 |
Chamber Upgrade for EPU48 in TPS |
3676 |
|
- I.C. Sheng, C.K. Chan, C.-C. Chang, C.M. Cheng, Y.T. Cheng, J. -Y. Chuang, Y.M. Hsiao, Y.T. Huang, C. Shueh, L.H. Wu, I.C. Yang
NSRRC, Hsinchu, Taiwan
|
|
|
Due to high total power and power density in Taiwan Photon Source (TPS) of EPU48 (Elliptical Polarized Undulator) in double minimum sector, we fabricate a new Aluminum vacuum chamber to increase sufficient room for synchrotron radiation to pass through without damage the storage ring chamber. A new method of in-site replacement of bending chamber is also presented, the result of this replacement procedure shows that it is very cost-effective as well as good UHV vacuum quality.
|
|
Export • |
reference for this paper to
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|
THPMY015 |
Measurement of the Pressure in the TPS Booster Ring |
3685 |
|
- C.M. Cheng, C.K. Chan, G.-Y. Hsiung, Y.T. Huang, I.C. Sheng, L.H. Wu, I.C. Yang
NSRRC, Hsinchu, Taiwan
|
|
|
The booster ring of Taiwan Photon Source (TPS) is designed to provide full energy injection 3 GeV ramped up from 150 MeV with a small beam emittance. It is a synchrotron accelerator of circumference 496.8 m. The vacuum chamber through the magnets is made of thin stainless-steel tube extruded to an elliptical cross section of inner diameters 35 mm and 20 mm, and thickness 0.7 mm. The other chambers have standard 35CF round tube. The vacuum system was baked in the first installation. Because the residual stress of the stainless-steel elliptical tubing caused the magnetic field to become unstable, all elliptical tubing was removed for annealing to proceed, and reinstalled without baking. The ultimate pressure and data for the residual gas are shown as follows.
|
|
Export • |
reference for this paper to
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|