IBIC2022 - List of Authors (Freitas, A.)

Paper	Title	Page
TUP41	Multi-Dimensional Feedforward Controller at MAX IV	335
	C. Takahashi, Á. Freitas, V. Hardion, M. Holz, M. Lindberg, M. Sjöström, H. Tarawneh MAX IV Laboratory, Lund University, Lund, Sweden
	Feedforward control loops are used in numerous applications to correct process variables. While feedforward control loops correct process variables according to expected behaviour of a system at any given set point, feedback loops require measurements of the output to correct deviations from the set point. At MAX IV, a generic multi-dimensional input and output feedforward controller was implemented using TANGO Control System. This paper describes the development and use cases of this controller for beam orbit and optics corrections at MAX IV.
	Poster TUP41 [1.597 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-IBIC2022-TUP41
About •	Received ※ 06 September 2022 — Revised ※ 10 September 2022 — Accepted ※ 11 September 2022 — Issue date ※ 15 September 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEP38	Control System Suite for Beam Position Monitors at MAX IV	496
	Á. Freitas, V. Hardion, M. Lindberg, R. Lindvall, R. Svärd, C. Takahashi MAX IV Laboratory, Lund University, Lund, Sweden
	MAX IV is a fourth generation synchrotron facility at Lund, Sweden. It is composed by a full energy linear accelerator and two storage rings with 1.5 GeV and 3 GeV, which requires hundreds of beam position monitors. In this context, Libera Single Pass E and Libera Brilliance⁺ are employed as BPM instruments. This paper will present an overview of the control system suite used in the facility, including the communication, data acquisition and storage pipelines, monitoring, configuration and software maintainability.
	Poster WEP38 [4.895 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-IBIC2022-WEP38
About •	Received ※ 07 September 2022 — Revised ※ 10 September 2022 — Accepted ※ 12 September 2022 — Issue date ※ 25 October 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Multi-Dimensional Feedforward Controller at MAX IV

335

C. Takahashi, Á. Freitas, V. Hardion, M. Holz, M. Lindberg, M. Sjöström, H. Tarawneh
MAX IV Laboratory, Lund University, Lund, Sweden

Feedforward control loops are used in numerous applications to correct process variables. While feedforward control loops correct process variables according to expected behaviour of a system at any given set point, feedback loops require measurements of the output to correct deviations from the set point. At MAX IV, a generic multi-dimensional input and output feedforward controller was implemented using TANGO Control System. This paper describes the development and use cases of this controller for beam orbit and optics corrections at MAX IV.

Poster TUP41 [1.597 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-IBIC2022-TUP41

About •

Received ※ 06 September 2022 — Revised ※ 10 September 2022 — Accepted ※ 11 September 2022 — Issue date ※ 15 September 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEP38

Control System Suite for Beam Position Monitors at MAX IV

496

Á. Freitas, V. Hardion, M. Lindberg, R. Lindvall, R. Svärd, C. Takahashi
MAX IV Laboratory, Lund University, Lund, Sweden

MAX IV is a fourth generation synchrotron facility at Lund, Sweden. It is composed by a full energy linear accelerator and two storage rings with 1.5 GeV and 3 GeV, which requires hundreds of beam position monitors. In this context, Libera Single Pass E and Libera Brilliance⁺ are employed as BPM instruments. This paper will present an overview of the control system suite used in the facility, including the communication, data acquisition and storage pipelines, monitoring, configuration and software maintainability.

Poster WEP38 [4.895 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-IBIC2022-WEP38

About •

Received ※ 07 September 2022 — Revised ※ 10 September 2022 — Accepted ※ 12 September 2022 — Issue date ※ 25 October 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)