IBIC2016 - List of Authors (Pietralla, N.)

Paper	Title	Page
TUPG42	Design of a Very Compact 130 MeV Møller Polarimeter for the S-DALINAC	438
	T. Bahlo, J. Enders, T. Kürzeder, N. Pietralla, J. Wissmann TU Darmstadt, Darmstadt, Germany
	Funding: Supported by the DFG through grants SFB 634 and GRK 2128 At the Superconducting Darmstadt Linear Accelerator S-DALINAC it is possible to accelerate electron beams to a maximum energy of up to 130 MeV. In the S-DALINAC Polarized Injector SPIN polarized electrons with a polarization of up to 86% can be produced. The polarization can be measured with two already mounted Mott polarimeters in the injector beamline where the electrons can have energies of up to 10 MeV. To allow polarization measurements behind the main accelerator a Moeller polarimeter suitable for energies between 50 MeV and 130 MeV is currently being developed. The rather low and variable beam energies result in a big and also variable scattering angle distribution. Combined with strict spatial boundary conditions at the designated mounting area necessitate a very compact set-up for the polarimeter. In addition to an overview over the planned polarimeter we will present drafts of the target chamber, the beam separation chamber including a angle-defining aperture and the separation dipole as well as the beamline to the detectors and the beam dump.
DOI •	reference for this paper ※ DOI:10.18429/JACoW-IBIC2016-TUPG42
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPG10	Phase and Energy Stabilization System at the S-Dalinac	638
	T. Bahlo, C. Burandt, L.E. Jürgensen, T. Kürzeder, N. Pietralla, J. Wissmann TU Darmstadt, Darmstadt, Germany F. Hug IKP, Mainz, Germany
	The Superconducting Darmstadt Linear Accelerator S‑DALINAC is a recirculating electron accelerator with a design energy of 130 MeV operating in cw. Before entering the 30 MeV main accelerator the low energetic electron beam passes both a normal-conducting injector beamline preparing the beam's 3 GHz time structure as well as a superconducting 10 MeV injector beamline for preacceleration. Since the superconducting injector accelerates on-crest while the main accelerator accelerates off-crest the beam phase is crucial for the efficiency of the acceleration process and the minimization of the energy spread. Due to thermal drifts of the normal-conducting injector cavities this injection phase varies by about 0.2 degree over a timescale of an hour. In order to compensate for these drifts, a high level phase controller has been implemented. Additionally a low-energy scraper system has been installed between the injector and main linac in order to lock both the phase and the energy spread at the linac entrance. We will present the hardware for the phase controller, the control algorithm and the scraper setup. A report on measurements showing the effect of both systems will be given.
DOI •	reference for this paper ※ DOI:10.18429/JACoW-IBIC2016-WEPG10
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Design of a Very Compact 130 MeV Møller Polarimeter for the S-DALINAC

438

T. Bahlo, J. Enders, T. Kürzeder, N. Pietralla, J. Wissmann
TU Darmstadt, Darmstadt, Germany

Funding: Supported by the DFG through grants SFB 634 and GRK 2128
At the Superconducting Darmstadt Linear Accelerator S-DALINAC it is possible to accelerate electron beams to a maximum energy of up to 130 MeV. In the S-DALINAC Polarized Injector SPIN polarized electrons with a polarization of up to 86% can be produced. The polarization can be measured with two already mounted Mott polarimeters in the injector beamline where the electrons can have energies of up to 10 MeV. To allow polarization measurements behind the main accelerator a Moeller polarimeter suitable for energies between 50 MeV and 130 MeV is currently being developed. The rather low and variable beam energies result in a big and also variable scattering angle distribution. Combined with strict spatial boundary conditions at the designated mounting area necessitate a very compact set-up for the polarimeter. In addition to an overview over the planned polarimeter we will present drafts of the target chamber, the beam separation chamber including a angle-defining aperture and the separation dipole as well as the beamline to the detectors and the beam dump.

DOI •

reference for this paper ※ DOI:10.18429/JACoW-IBIC2016-TUPG42

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPG10

Phase and Energy Stabilization System at the S-Dalinac

638

T. Bahlo, C. Burandt, L.E. Jürgensen, T. Kürzeder, N. Pietralla, J. Wissmann
TU Darmstadt, Darmstadt, Germany
F. Hug
IKP, Mainz, Germany

The Superconducting Darmstadt Linear Accelerator S‑DALINAC is a recirculating electron accelerator with a design energy of 130 MeV operating in cw. Before entering the 30 MeV main accelerator the low energetic electron beam passes both a normal-conducting injector beamline preparing the beam's 3 GHz time structure as well as a superconducting 10 MeV injector beamline for preacceleration. Since the superconducting injector accelerates on-crest while the main accelerator accelerates off-crest the beam phase is crucial for the efficiency of the acceleration process and the minimization of the energy spread. Due to thermal drifts of the normal-conducting injector cavities this injection phase varies by about 0.2 degree over a timescale of an hour. In order to compensate for these drifts, a high level phase controller has been implemented. Additionally a low-energy scraper system has been installed between the injector and main linac in order to lock both the phase and the energy spread at the linac entrance. We will present the hardware for the phase controller, the control algorithm and the scraper setup. A report on measurements showing the effect of both systems will be given.

DOI •

reference for this paper ※ DOI:10.18429/JACoW-IBIC2016-WEPG10

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)