SRF2013 - List of Authors (Sekutowicz, J.K.)

Paper

Title

Page

Towards a 100mA Superconducting RF Photoinjector for BERLinPro

42

A. Neumann, W. Anders, A. Burrill, A. Jankowiak, T. Kamps, J. Knobloch, O. Kugeler, P. Lauinger, A.N. Matveenko, M. Schmeißer, J. Völker
HZB, Berlin, Germany
G. Ciovati, P. Kneisel
JLAB, Newport News, Virginia, USA
R. Nietubyć
NCBJ, Świerk/Otwock, Poland
S.G. Schubert, J. Smedley
BNL, Upton, Long Island, New York, USA
J.K. Sekutowicz
DESY, Hamburg, Germany
V. Volkov
BINP SB RAS, Novosibirsk, Russia
I. Will
MBI, Berlin, Germany
E.N. Zaplatin
FZJ, Jülich, Germany

For BERLinPro, a 100 mA CW-driven SRF energy recovery linac demonstrator facility, HZB needs to develop a photo-injector superconducting cavity which delivers a at least 1mm*mr emittance beam at high average current. To address these challenges of producing a high peak brightness beam at high repetition rate, at first HZB tested a fully superconducting injector with a lead cathode*,followed now by the design of a SC cavity allowing operation up to 4 mA using CW-modified TTF-III couplers and inserting a normal conducting high quantum efficiency cathode using the HZDR-style insert scheme. This talk will present the latest results and an overview of the measurements with the lead cathode cavity and will describe the design and optimization process, the first production results of the current design and an outlook to the further development steps towards the full power version.
*T. Kamps et al., Proceedings of the 2nd International Particle Accelerator Conference, San Sebastián, Spain, 2011.

Slides MOIOB02 [7.574 MB]

MOP086

Integration, Commissioning and Cryogenics Performance of the ERL Cryomodule Installed on ALICE-ERL Facility at STFC Daresbury Laboratory, UK

349

S.M. Pattalwar, R.K. Buckley, P.A. Corlett, P. Goudket, A.R. Goulden, A.J. May, P.A. McIntosh, A.E. Wheelhouse
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom
S.A. Belomestnykh
BNL, Upton, Long Island, New York, USA
A. Büchner, F.G. Gabriel, P. Michel
HZDR, Dresden, Germany
E.P. Chojnacki, J.V. Conway, R.G. Eichhorn, G.H. Hoffstaetter, M. Liepe, H. Padamsee, P. Quigley, J. Sears, V.D. Shemelin
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
M.A. Cordwell, T.J. Jones, L. Ma, A.J. Moss, J. Strachan
STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom
J.N. Corlett, D. Li, S.M. Lidia
LBNL, Berkeley, California, USA
T. Kimura
Stanford University, Stanford, California, USA
R.E. Laxdal
TRIUMF, Canada's National Laboratory for Particle and Nuclear Physics, Vancouver, Canada
J.K. Sekutowicz
DESY, Hamburg, Germany
T.J. Smith
SLAC, Menlo Park, California, USA

On successful assembly and preliminary testing of an optimised SRF cryomodule for application on ERL accelerators, which is being developed through an international collaboration the cryomodule has been installed on the 35 MeV ALICE (Accelerators and Lasers in Combined Experiments) Energy Recovery Linac (ERL) facility at STFC Daresbury Laboratory. Existing cryogenic infrastructure has a capacity to deliver approximately 120 W cooling power at 2 K, but the HOM (Higher Order Mode) absorbers, the thermal intercepts for the high power RF couplers and the radiation shield in the cryomodule are designed to be cooled (to 5 K and 80 K) with gaseous helium instead of liquid nitrogen. As a result the cryogenic infrastructure for ALICE had to be modified to meet these additional requirements. In this paper we describe our experience with the process of integration and the cryogenic commissioning, and present some initial results.

TUP053

Estimation of Small Geometry Deviation for TESLA-Shape Cavities Due to Inner Surface Polishing

537

A.A. Sulimov, G. Kreps, J.K. Sekutowicz
DESY, Hamburg, Germany

Two well know polishing methods are used for the inner surface cleaning of superconducting TESLA-shape cavities: electro-polishing (EP) or buffered chemical polishing (BCP). The amount of removed material is relatively small and varies from 10 till 140 um. The cavity after polishing is closed to prevent the scratches or dust appearing on its inner surface. The estimation of the removed material amount is possible by different criteria, for example by comparison of weight before and after cleaning, or by the time - cleaning procedure duration. Both calculations could give us only approximate average value of the removed material amount. We describe the method for estimation of small geometry deviation basing on RF frequency measurements, which allows calculating the different influence of surface treatment on the iris and equator areas.

Poster TUP053 [0.785 MB]

THP059

HOM Coupler Design Adjustment for CW operation of the 1.3 GHz 9-cell TESLA Type SRF Cavity

1051

D. Kostin, W.-D. Möller, J.K. Sekutowicz
DESY, Hamburg, Germany

One of the key features of a modern research facility is its versatility, ability to adjust for a multitude of the applications and user needs. A challenge for the coming European XFEL is to become a multipurpose laboratory with a broad applications spectrum. Primarily, the XFEL is a pulsed machine. Encompassing the CW mode would be a worthy addition. CW operation of the 1.3GHz 9-cell TESLA Type SRF Cavity was performed several times at DESY and other Labs successfully. One of the difficulties was a heat load of the High Order Mode (HOM) couplers. To amend this HOM coupler design adjustement is proposed, simulated and modelled. Results are presented and discussed.

THP086

LLRF System Design and Performance for XFEL Cryomodules Continuous Wave Operation

1129

J. Branlard, V. Ayvazyan, Ł. Butkowski, K.P. Przygoda, H. Schlarb, J.K. Sekutowicz
DESY, Hamburg, Germany
W. Cichalewski, A. Piotrowski
TUL-DMCS, Łódź, Poland
W. Jałmużna
Embedded Integrated Control Systems GmbH, Hamburg, Germany
J. Szewiński
NCBJ, Świerk/Otwock, Poland

The Cryomodule Test Bench (CMTB) at DESY is equipped with a 100 kW Inductive Output Tube (IOT) allowing the test of superconducting cryomodules in continuous wave (CW) operation mode. Although significantly different from the nominal pulsed operation mode of the European X-Ray Free Electron Laser (XFEL), CW operation can be handled by the same Low-level Radio Frequency (LLRF) system, within minor firmware modifications. The hardware details of the LLRF setup at CMTB, the firmware and software architecture and performance results from the last CW test are presented in this contribution.

Paper	Title	Page
MOIOB02	Towards a 100mA Superconducting RF Photoinjector for BERLinPro	42
	A. Neumann, W. Anders, A. Burrill, A. Jankowiak, T. Kamps, J. Knobloch, O. Kugeler, P. Lauinger, A.N. Matveenko, M. Schmeißer, J. Völker HZB, Berlin, Germany G. Ciovati, P. Kneisel JLAB, Newport News, Virginia, USA R. Nietubyć NCBJ, Świerk/Otwock, Poland S.G. Schubert, J. Smedley BNL, Upton, Long Island, New York, USA J.K. Sekutowicz DESY, Hamburg, Germany V. Volkov BINP SB RAS, Novosibirsk, Russia I. Will MBI, Berlin, Germany E.N. Zaplatin FZJ, Jülich, Germany
	For BERLinPro, a 100 mA CW-driven SRF energy recovery linac demonstrator facility, HZB needs to develop a photo-injector superconducting cavity which delivers a at least 1mmmr emittance beam at high average current. To address these challenges of producing a high peak brightness beam at high repetition rate, at first HZB tested a fully superconducting injector with a lead cathode,followed now by the design of a SC cavity allowing operation up to 4 mA using CW-modified TTF-III couplers and inserting a normal conducting high quantum efficiency cathode using the HZDR-style insert scheme. This talk will present the latest results and an overview of the measurements with the lead cathode cavity and will describe the design and optimization process, the first production results of the current design and an outlook to the further development steps towards the full power version. *T. Kamps et al., Proceedings of the 2nd International Particle Accelerator Conference, San Sebastián, Spain, 2011.
	Slides MOIOB02 [7.574 MB]

MOP086	Integration, Commissioning and Cryogenics Performance of the ERL Cryomodule Installed on ALICE-ERL Facility at STFC Daresbury Laboratory, UK	349
	S.M. Pattalwar, R.K. Buckley, P.A. Corlett, P. Goudket, A.R. Goulden, A.J. May, P.A. McIntosh, A.E. Wheelhouse STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom S.A. Belomestnykh BNL, Upton, Long Island, New York, USA A. Büchner, F.G. Gabriel, P. Michel HZDR, Dresden, Germany E.P. Chojnacki, J.V. Conway, R.G. Eichhorn, G.H. Hoffstaetter, M. Liepe, H. Padamsee, P. Quigley, J. Sears, V.D. Shemelin Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA M.A. Cordwell, T.J. Jones, L. Ma, A.J. Moss, J. Strachan STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom J.N. Corlett, D. Li, S.M. Lidia LBNL, Berkeley, California, USA T. Kimura Stanford University, Stanford, California, USA R.E. Laxdal TRIUMF, Canada's National Laboratory for Particle and Nuclear Physics, Vancouver, Canada J.K. Sekutowicz DESY, Hamburg, Germany T.J. Smith SLAC, Menlo Park, California, USA
	On successful assembly and preliminary testing of an optimised SRF cryomodule for application on ERL accelerators, which is being developed through an international collaboration the cryomodule has been installed on the 35 MeV ALICE (Accelerators and Lasers in Combined Experiments) Energy Recovery Linac (ERL) facility at STFC Daresbury Laboratory. Existing cryogenic infrastructure has a capacity to deliver approximately 120 W cooling power at 2 K, but the HOM (Higher Order Mode) absorbers, the thermal intercepts for the high power RF couplers and the radiation shield in the cryomodule are designed to be cooled (to 5 K and 80 K) with gaseous helium instead of liquid nitrogen. As a result the cryogenic infrastructure for ALICE had to be modified to meet these additional requirements. In this paper we describe our experience with the process of integration and the cryogenic commissioning, and present some initial results.

TUP053	Estimation of Small Geometry Deviation for TESLA-Shape Cavities Due to Inner Surface Polishing	537
	A.A. Sulimov, G. Kreps, J.K. Sekutowicz DESY, Hamburg, Germany
	Two well know polishing methods are used for the inner surface cleaning of superconducting TESLA-shape cavities: electro-polishing (EP) or buffered chemical polishing (BCP). The amount of removed material is relatively small and varies from 10 till 140 um. The cavity after polishing is closed to prevent the scratches or dust appearing on its inner surface. The estimation of the removed material amount is possible by different criteria, for example by comparison of weight before and after cleaning, or by the time - cleaning procedure duration. Both calculations could give us only approximate average value of the removed material amount. We describe the method for estimation of small geometry deviation basing on RF frequency measurements, which allows calculating the different influence of surface treatment on the iris and equator areas.
	Poster TUP053 [0.785 MB]

THP059	HOM Coupler Design Adjustment for CW operation of the 1.3 GHz 9-cell TESLA Type SRF Cavity	1051
	D. Kostin, W.-D. Möller, J.K. Sekutowicz DESY, Hamburg, Germany
	One of the key features of a modern research facility is its versatility, ability to adjust for a multitude of the applications and user needs. A challenge for the coming European XFEL is to become a multipurpose laboratory with a broad applications spectrum. Primarily, the XFEL is a pulsed machine. Encompassing the CW mode would be a worthy addition. CW operation of the 1.3GHz 9-cell TESLA Type SRF Cavity was performed several times at DESY and other Labs successfully. One of the difficulties was a heat load of the High Order Mode (HOM) couplers. To amend this HOM coupler design adjustement is proposed, simulated and modelled. Results are presented and discussed.

THP086	LLRF System Design and Performance for XFEL Cryomodules Continuous Wave Operation	1129
	J. Branlard, V. Ayvazyan, Ł. Butkowski, K.P. Przygoda, H. Schlarb, J.K. Sekutowicz DESY, Hamburg, Germany W. Cichalewski, A. Piotrowski TUL-DMCS, Łódź, Poland W. Jałmużna Embedded Integrated Control Systems GmbH, Hamburg, Germany J. Szewiński NCBJ, Świerk/Otwock, Poland
	The Cryomodule Test Bench (CMTB) at DESY is equipped with a 100 kW Inductive Output Tube (IOT) allowing the test of superconducting cryomodules in continuous wave (CW) operation mode. Although significantly different from the nominal pulsed operation mode of the European X-Ray Free Electron Laser (XFEL), CW operation can be handled by the same Low-level Radio Frequency (LLRF) system, within minor firmware modifications. The hardware details of the LLRF setup at CMTB, the firmware and software architecture and performance results from the last CW test are presented in this contribution.