SRF2013 - List of Authors (Muller, K.)

Paper	Title	Page
TUP046	Vertical Electropolishing of SRF Cavities and its Parameters Investigation	514
	F. Eozénou, F. Ballester, Y. Boudigou, P. Carbonnier, J.-P. Charrier, Y. Gasser, D. Roudier, C. Servouin CEA/DSM/IRFU, France K. Muller Grenoble-INP Phelma, Grenoble, France
	Funding: We acknowledge the support of the European Community-Research Infrastructure Activity under the FP7 program (EuCARD, Contract No. 227579),and the support of the ‘‘Conseil General de l’Essonne’’(ASTRE) An advanced set-up for vertical electropolishing (VEP) of SRF niobium elliptical cavities is operating at CEA Saclay. Cavities are VEP’ed with circulating standard HF-H2SO4 electrolyte. Parameters such as voltage, cathode shape, acid flow and temperature were investigated. Low-voltage (<7V), high acid flow (25L/min) and low acid temperature (20°C) are considered as promising parameters. Such recipe was tested on single-cell and 9-cell ILC cavities with nice surface finishing. After 60 μm VEP on a HEP'ed single-cell, the cavity show similar performance at 1.6K compared to previous Horizontal EP: (Eacc > 41MV/m) limited by quench. Another cavity reaches 36MV/m after 300μm removal by VEP in spite of a pitted surface due to initial VEP treatment at higher temperature (> 30°C). The baking effect after HEP/VEP is similar. An asymmetric niobium removal is observed with faster polishing in the upper cell. Nice surface finishing as well as standard Q0 value are obtained at low/medium field on 9Cell but achieved performance is limited by Field Emission. F. Eozenou et al., PRST-AB, 15, 083501 (2012)

Paper

Title

Page

Vertical Electropolishing of SRF Cavities and its Parameters Investigation

514

F. Eozénou, F. Ballester, Y. Boudigou, P. Carbonnier, J.-P. Charrier, Y. Gasser, D. Roudier, C. Servouin
CEA/DSM/IRFU, France
K. Muller
Grenoble-INP Phelma, Grenoble, France

Funding: We acknowledge the support of the European Community-Research Infrastructure Activity under the FP7 program (EuCARD, Contract No. 227579),and the support of the ‘‘Conseil General de l’Essonne’’(ASTRE)
An advanced set-up for vertical electropolishing (VEP) of SRF niobium elliptical cavities is operating at CEA Saclay*. Cavities are VEP’ed with circulating standard HF-H2SO4 electrolyte. Parameters such as voltage, cathode shape, acid flow and temperature were investigated. Low-voltage (<7V), high acid flow (25L/min) and low acid temperature (20°C) are considered as promising parameters. Such recipe was tested on single-cell and 9-cell ILC cavities with nice surface finishing. After 60 μm VEP on a HEP'ed single-cell, the cavity show similar performance at 1.6K compared to previous Horizontal EP: (Eacc > 41MV/m) limited by quench. Another cavity reaches 36MV/m after 300μm removal by VEP in spite of a pitted surface due to initial VEP treatment at higher temperature (> 30°C). The baking effect after HEP/VEP is similar. An asymmetric niobium removal is observed with faster polishing in the upper cell. Nice surface finishing as well as standard Q0 value are obtained at low/medium field on 9Cell but achieved performance is limited by Field Emission.
*F. Eozenou et al., PRST-AB, 15, 083501 (2012)