SRF2013 - List of Authors (Kaluzny, J.A.)

Paper	Title	Page
MOP009	A Summary of the Advanced Photon Source (APS) Short Pulse X-ray (SPX) R&D Accomplishments	92
	A. Nassiri, N.D. Arnold, T.G. Berenc, M. Borland, B. Brajuskovic, D.J. Bromberek, J. Carwardine, G. Decker, L. Emery, J.D. Fuerst, J.P. Holzbauer, D. Horan, J.A. Kaluzny, J.S. Kerby, F. Lenkszus, R.M. Lill, H. Ma, V. Sajaev, B.K. Stillwell, G.J. Waldschmidt, M. White, G. Wu, Y. Yang, A. Zholents ANL, Argonne, USA J.M. Byrd, L.R. Doolittle, G. Huang LBNL, Berkeley, California, USA P. Dhakal, J. Henry, J.D. Mammosser, J. Matalevich, R.A. Rimmer, H. Wang, K.M. Wilson JLAB, Newport News, Virginia, USA Z. Li, L. Xiao SLAC, Menlo Park, California, USA
	Funding: Work supported by the U.S. Department of Energy, Office of Science, under Contract No. DE-AC02-06H11357. The Advanced Photon Source Upgrade Project (APS-U) at Argonne will include generation of short-pulse x-rays based on Zholents’ [1] deflecting cavity scheme. We have chosen superconducting (SC) cavities in order to have a continuous train of crabbed bunches and flexibility of operating modes. Since early 2012, in collaboration with Jefferson National Laboratory, we have made significant progress prototyping and testing a number of single-cell deflecting cavities. We have designed, prototyped, and tested silicon carbide as damping material for higher-order-mode (HOM) dampers, which are broadband to handle the HOM power across the frequency spectrum produced by the APS beam. In collaboration with Lawrence Berkeley National Laboratory, we have developing a state-of-the-art timing and synchronization system for distributing stable rf signals over optical fiber capable of achieving tens of femtoseconds phase drift and jitter. Collaboration with the Advanced Computations Department at Stanford Linear Accelerator Center is looking into simulations of complex, multi- cavity geometries. This contribution provides a progress report on the current R&D status of the SPX project. [1] A. Zholents et al., NIM A 425, 385 (1999).

MOP078	Horizontal Testing of a Dressed Deflecting Mode Cavity for the APS Upgrade Short Pulse X-Ray Project	321
	J.P. Holzbauer, N.D. Arnold, T.G. Berenc, D.J. Bromberek, J. Carwardine, N.P. Di Monte, J.D. Fuerst, A.E. Grelick, D. Horan, J.A. Kaluzny, J.W. Lang, H. Ma, T.L. Mann, D.A. Meyer, M.E. Middendorf, A. Nassiri, Y. Shiroyanagi, J.H. Vacca, G.J. Waldschmidt, R.D. Wright, G. Wu, Y. Yang, A. Zholents ANL, Argonne, USA E.R. Harms, W. Schappert Fermilab, Batavia, USA J.D. Mammosser JLAB, Newport News, Virginia, USA
	Funding: Work supported by the U.S. Department of Energy, Office of Science, under Contract No. DE-AC02-06CHI1357. The short pulse x-ray (SPX) part of the Advanced Photon Source (APS) Upgrade is an effort to enhance time-resolved experiments on a few-ps-scale at the APS. The goal of SPX is the generation of short pulses of x-rays for pump-probe time-resolved capability using superconducting rf (SRF) deflecting cavities. These cavities will create a correlation between longitudinal position in the electron bunch and vertical momentum. The light produced by this bunch can be passed through a slit to produce a pulse of light much shorter (1-2 ps instead of 100 ps) than the bunch length at reduced flux. An SPX cavity has been tested with a helium vessel and tuner. In addition to studying rf performance with more realistic cooling, this test allowed integration and operation of many systems designed for SPX cryomodule in-ring operation. These systems included an APS-constructed 5 kW, 2.815 GHz amplifier, a digital low-level rf controller system designed and fabricated in collaboration with LBNL, a cavity tuner, and instrumentation systems designed for the existing APS infrastructure. Cavity performance and subsystem performance will be reported and discussed in this paper. A. Zholents et al., NIM A 425, 385 (1999). ** A. Nassiri et al., “Status of the Short-Pulse X-Ray Project at the Advanced Photon Source,” IPAC 2012, New Orleans, LA, May 2012.

MOP079	Design and Test of a Cryogenic Seal for Rectangular Waveguide Using VATSEAL Technology	325
	J.D. Fuerst, J.P. Holzbauer, J.A. Kaluzny, C.R. Montiel, Y. Shiroyanagi, B.K. Stillwell ANL, Argonne, USA
	Funding: This work was supported by the U. S. Department of Energy, Office of Science, under contract No. DE-AC02-06CH11357. A commercially available rectangular metal seal from VAT Vacuum Valves AG has been evaluated and cold tested as a possible cryogenic seal for srf cavities. A program of analysis and cryogenic testing was undertaken to evaluate seal parameters and suitability. Seal line loads, bolt torque and resultant flange/seal deformation at low temperature and during thermal cycling were calculated both statically and via time-dependent numerical simulation to confirm the mechanical integrity of the flange/seal system. Cold testing of flange/waveguide assemblies included thermal shocks in liquid nitrogen and realistic cool-downs below the λ point. Acceptable seal performance has been demonstrated under all test conditions although seal joint assembly is sensitive to details including bolt torque, flange flatness, and surface finish.

TUP055	Electropolishing of the ANL Deflecting Cavity for the APS Upgrade	544
	Y. Yang, J.D. Fuerst, J.P. Holzbauer, J.A. Kaluzny, A. Nassiri, G. Wu ANL, Argonne, USA A.C. Crawford Fermilab, Batavia, USA P. Dhakal, J.D. Mammosser, H. Wang JLAB, Newport News, Virginia, USA Y. Yang TUB, Beijing, People's Republic of China
	Studies on the application of electropolishing (EP) of the ANL superconducting deflecting cavity have shown promising results. This cavity geometry is a squashed single-cell cavity with Y-end group waveguide as well as on-cell LOM damper. The cavity works at TM110-like deflecting mode, in which the iris between the cavity cell and the Y-end group is the highest magnetic field region. Before EP, the cavity had been chemically etched (BCP) several times. Forty-um EP processing was performed on one Mark II prototype deflecting cavity at Fermilab. No mild baking was performed before the cavity vertical test. The test showed that the low-field Q had improved from 2·10⁹ to 3·10⁹ and the high-field Q-slope had been successfully removed. The quench limit was slightly improved from 10⁶ mT to 113 mT. Fast T-mapping had detected a significant decrease of local temperature rise in the cavity iris. Optical inspection before EP found a lot of grooves around the iris, which might be related to the gas bubbles generated during BCP. This suggests that horizontal EP is a promising processing technique to remove the high-field Q-slope and improve the deflecting cavity performance.

Paper

Title

Page

A Summary of the Advanced Photon Source (APS) Short Pulse X-ray (SPX) R&D Accomplishments

92

A. Nassiri, N.D. Arnold, T.G. Berenc, M. Borland, B. Brajuskovic, D.J. Bromberek, J. Carwardine, G. Decker, L. Emery, J.D. Fuerst, J.P. Holzbauer, D. Horan, J.A. Kaluzny, J.S. Kerby, F. Lenkszus, R.M. Lill, H. Ma, V. Sajaev, B.K. Stillwell, G.J. Waldschmidt, M. White, G. Wu, Y. Yang, A. Zholents
ANL, Argonne, USA
J.M. Byrd, L.R. Doolittle, G. Huang
LBNL, Berkeley, California, USA
P. Dhakal, J. Henry, J.D. Mammosser, J. Matalevich, R.A. Rimmer, H. Wang, K.M. Wilson
JLAB, Newport News, Virginia, USA
Z. Li, L. Xiao
SLAC, Menlo Park, California, USA

Funding: Work supported by the U.S. Department of Energy, Office of Science, under Contract No. DE-AC02-06H11357.
The Advanced Photon Source Upgrade Project (APS-U) at Argonne will include generation of short-pulse x-rays based on Zholents’ [1] deflecting cavity scheme. We have chosen superconducting (SC) cavities in order to have a continuous train of crabbed bunches and flexibility of operating modes. Since early 2012, in collaboration with Jefferson National Laboratory, we have made significant progress prototyping and testing a number of single-cell deflecting cavities. We have designed, prototyped, and tested silicon carbide as damping material for higher-order-mode (HOM) dampers, which are broadband to handle the HOM power across the frequency spectrum produced by the APS beam. In collaboration with Lawrence Berkeley National Laboratory, we have developing a state-of-the-art timing and synchronization system for distributing stable rf signals over optical fiber capable of achieving tens of femtoseconds phase drift and jitter. Collaboration with the Advanced Computations Department at Stanford Linear Accelerator Center is looking into simulations of complex, multi- cavity geometries. This contribution provides a progress report on the current R&D status of the SPX project.
[1] A. Zholents et al., NIM A 425, 385 (1999).

MOP078

Horizontal Testing of a Dressed Deflecting Mode Cavity for the APS Upgrade Short Pulse X-Ray Project

321

J.P. Holzbauer, N.D. Arnold, T.G. Berenc, D.J. Bromberek, J. Carwardine, N.P. Di Monte, J.D. Fuerst, A.E. Grelick, D. Horan, J.A. Kaluzny, J.W. Lang, H. Ma, T.L. Mann, D.A. Meyer, M.E. Middendorf, A. Nassiri, Y. Shiroyanagi, J.H. Vacca, G.J. Waldschmidt, R.D. Wright, G. Wu, Y. Yang, A. Zholents
ANL, Argonne, USA
E.R. Harms, W. Schappert
Fermilab, Batavia, USA
J.D. Mammosser
JLAB, Newport News, Virginia, USA

Funding: Work supported by the U.S. Department of Energy, Office of Science, under Contract No. DE-AC02-06CHI1357.
The short pulse x-ray (SPX) part of the Advanced Photon Source (APS) Upgrade is an effort to enhance time-resolved experiments on a few-ps-scale at the APS. The goal of SPX is the generation of short pulses of x-rays for pump-probe time-resolved capability using superconducting rf (SRF) deflecting cavities*. These cavities will create a correlation between longitudinal position in the electron bunch and vertical momentum**. The light produced by this bunch can be passed through a slit to produce a pulse of light much shorter (1-2 ps instead of 100 ps) than the bunch length at reduced flux. An SPX cavity has been tested with a helium vessel and tuner. In addition to studying rf performance with more realistic cooling, this test allowed integration and operation of many systems designed for SPX cryomodule in-ring operation. These systems included an APS-constructed 5 kW, 2.815 GHz amplifier, a digital low-level rf controller system designed and fabricated in collaboration with LBNL, a cavity tuner, and instrumentation systems designed for the existing APS infrastructure. Cavity performance and subsystem performance will be reported and discussed in this paper.
* A. Zholents et al., NIM A 425, 385 (1999).
** A. Nassiri et al., “Status of the Short-Pulse X-Ray Project at the Advanced Photon Source,” IPAC 2012, New Orleans, LA, May 2012.

MOP079

Design and Test of a Cryogenic Seal for Rectangular Waveguide Using VATSEAL Technology

325

J.D. Fuerst, J.P. Holzbauer, J.A. Kaluzny, C.R. Montiel, Y. Shiroyanagi, B.K. Stillwell
ANL, Argonne, USA

Funding: This work was supported by the U. S. Department of Energy, Office of Science, under contract No. DE-AC02-06CH11357.
A commercially available rectangular metal seal from VAT Vacuum Valves AG has been evaluated and cold tested as a possible cryogenic seal for srf cavities. A program of analysis and cryogenic testing was undertaken to evaluate seal parameters and suitability. Seal line loads, bolt torque and resultant flange/seal deformation at low temperature and during thermal cycling were calculated both statically and via time-dependent numerical simulation to confirm the mechanical integrity of the flange/seal system. Cold testing of flange/waveguide assemblies included thermal shocks in liquid nitrogen and realistic cool-downs below the λ point. Acceptable seal performance has been demonstrated under all test conditions although seal joint assembly is sensitive to details including bolt torque, flange flatness, and surface finish.

TUP055

Electropolishing of the ANL Deflecting Cavity for the APS Upgrade

544

Y. Yang, J.D. Fuerst, J.P. Holzbauer, J.A. Kaluzny, A. Nassiri, G. Wu
ANL, Argonne, USA
A.C. Crawford
Fermilab, Batavia, USA
P. Dhakal, J.D. Mammosser, H. Wang
JLAB, Newport News, Virginia, USA
Y. Yang
TUB, Beijing, People's Republic of China

Studies on the application of electropolishing (EP) of the ANL superconducting deflecting cavity have shown promising results. This cavity geometry is a squashed single-cell cavity with Y-end group waveguide as well as on-cell LOM damper. The cavity works at TM110-like deflecting mode, in which the iris between the cavity cell and the Y-end group is the highest magnetic field region. Before EP, the cavity had been chemically etched (BCP) several times. Forty-um EP processing was performed on one Mark II prototype deflecting cavity at Fermilab. No mild baking was performed before the cavity vertical test. The test showed that the low-field Q had improved from 2·10⁹ to 3·10⁹ and the high-field Q-slope had been successfully removed. The quench limit was slightly improved from 10⁶ mT to 113 mT. Fast T-mapping had detected a significant decrease of local temperature rise in the cavity iris. Optical inspection before EP found a lot of grooves around the iris, which might be related to the gas bubbles generated during BCP. This suggests that horizontal EP is a promising processing technique to remove the high-field Q-slope and improve the deflecting cavity performance.