SRF2013 - List of Authors (Hardy, P.)

Paper

Title

Page

Cavity Development for the Linear IFMIF Prototype Accelerator

878

N. Bazin, P. Carbonnier, G. Devanz, G. Disset, N. Grouas, P. Hardy, F. Orsini, D. Roudier
CEA/DSM/IRFU, France
J. Neyret
CEA/IRFU, Gif-sur-Yvette, France

The Linear IFMIF Prototype Accelerator (LIPAc), which is presently under design and realization, aims to accelerate a 125 mA deuteron beam up to 9 MeV. Therefore, a low-beta 175 MHz Half-Wave Resonator (HWR) was initially designed and manufactured with a tuning system based on a capacitive plunger located in the electric field region. Following the results of the vertical tests at 4.2K, this tuning system was abandoned and replaced by a conservative solution based on the HWR wall deformation using an external mechanical tuner. This paper will focus on the manufacturing of the prototype cavity, the studies realized to explain the first test results and the solutions taken to overcome the difficulties, leading to the validation of the prototype. Then, we will present the new cavity design.

Slides THIOD03 [8.845 MB]

FRIOC02

ESS Elliptical Cavities and Cryomodules

1218

G. Devanz, P. Bosland, M. Desmons, P. Hardy, F. Leseigneur, M. Luong, F. Peauger, J. Plouin, D. Roudier
CEA/DSM/IRFU, France
N. Bazin
CEA/IRFU, Gif-sur-Yvette, France
G. Costanza
Lund University, Lund, Sweden
G. Olivier
IPN, Orsay, France

The accelerator of the European Spallation Source (ESS) is a 5 MW proton linac to be built in Lund Sweden. Its superconducting section is composed of 3 cavity families: double spoke resonators, medium beta and high beta elliptical multicell cavities. This paper presents the electromagnetic and mechanical design of the 704.42 MHz elliptical cavities. Both elliptical famillies are housed in 4-cavity cryomodules which share a common design and set of components which will be described here.

Slides FRIOC02 [3.475 MB]

THP056

Validation Procedures for the IFMIF Power Coupler Prototypes

1043

H. Jenhani, P. Carbonnier, Y. Gasser, N. Grouas, P. Hardy, V.M. Hennion, F. Orsini, Y. Penichot, B. Renard, D. Roudier
CEA/IRFU, Gif-sur-Yvette, France
S.J. Einarson, T.A. Treado
CPI, Beverley, Massachusetts, USA
D. Regidor, M. Weber
CIEMAT, Madrid, Spain

In the framework of the International Fusion Materials Irradiation Facility (IFMIF), which consists of two high power CW accelerator drivers, each delivering a 125 mA deuteron beam at 40 MeV, a Linear IFMIF Prototype Accelerator (LIPAc) is presently under design for the first phase of the project. The first two IFMIF Power Coupler Prototypes were manufactured for LIPAc. Series of acceptance tests have been performed successfully. Prototype Power Couplers have been then cleaned and assembled in an ISO 5 cleanroom. A dedicated test bench allowing RF conditioning of the couplers up to 200 kW CW at 175 MHz was achieved. RF power conditioning is planned to start during October 2013.

Paper	Title	Page
THIOD03	Cavity Development for the Linear IFMIF Prototype Accelerator	878
	N. Bazin, P. Carbonnier, G. Devanz, G. Disset, N. Grouas, P. Hardy, F. Orsini, D. Roudier CEA/DSM/IRFU, France J. Neyret CEA/IRFU, Gif-sur-Yvette, France
	The Linear IFMIF Prototype Accelerator (LIPAc), which is presently under design and realization, aims to accelerate a 125 mA deuteron beam up to 9 MeV. Therefore, a low-beta 175 MHz Half-Wave Resonator (HWR) was initially designed and manufactured with a tuning system based on a capacitive plunger located in the electric field region. Following the results of the vertical tests at 4.2K, this tuning system was abandoned and replaced by a conservative solution based on the HWR wall deformation using an external mechanical tuner. This paper will focus on the manufacturing of the prototype cavity, the studies realized to explain the first test results and the solutions taken to overcome the difficulties, leading to the validation of the prototype. Then, we will present the new cavity design.
	Slides THIOD03 [8.845 MB]

FRIOC02	ESS Elliptical Cavities and Cryomodules	1218
	G. Devanz, P. Bosland, M. Desmons, P. Hardy, F. Leseigneur, M. Luong, F. Peauger, J. Plouin, D. Roudier CEA/DSM/IRFU, France N. Bazin CEA/IRFU, Gif-sur-Yvette, France G. Costanza Lund University, Lund, Sweden G. Olivier IPN, Orsay, France
	The accelerator of the European Spallation Source (ESS) is a 5 MW proton linac to be built in Lund Sweden. Its superconducting section is composed of 3 cavity families: double spoke resonators, medium beta and high beta elliptical multicell cavities. This paper presents the electromagnetic and mechanical design of the 704.42 MHz elliptical cavities. Both elliptical famillies are housed in 4-cavity cryomodules which share a common design and set of components which will be described here.
	Slides FRIOC02 [3.475 MB]

THP056	Validation Procedures for the IFMIF Power Coupler Prototypes	1043
	H. Jenhani, P. Carbonnier, Y. Gasser, N. Grouas, P. Hardy, V.M. Hennion, F. Orsini, Y. Penichot, B. Renard, D. Roudier CEA/IRFU, Gif-sur-Yvette, France S.J. Einarson, T.A. Treado CPI, Beverley, Massachusetts, USA D. Regidor, M. Weber CIEMAT, Madrid, Spain
	In the framework of the International Fusion Materials Irradiation Facility (IFMIF), which consists of two high power CW accelerator drivers, each delivering a 125 mA deuteron beam at 40 MeV, a Linear IFMIF Prototype Accelerator (LIPAc) is presently under design for the first phase of the project. The first two IFMIF Power Coupler Prototypes were manufactured for LIPAc. Series of acceptance tests have been performed successfully. Prototype Power Couplers have been then cleaned and assembled in an ISO 5 cleanroom. A dedicated test bench allowing RF conditioning of the couplers up to 200 kW CW at 175 MHz was achieved. RF power conditioning is planned to start during October 2013.