KEK, Ibaraki
A few issues on the path of the luminosity upgrade of KEKB B-Factory is described, including coherent synchrotron radiation, design of the interaction region, crab crossing, and high current operation. These issues will raise more obstacles on the upgrade with the High-Current Scheme. As an alternative, {¥it Nano-Beam Scheme} should be considered as a possible option for the upgrade.
KEK, Ibaraki
The titanium nitride (TiN) coating inside a beam duct has been recently attracting attention as a measure to mitigate the electron cloud effect in positron/proton rings. Here studied is the gas desorption from the TiN-coated copper beam duct, which will be adopted in the upgrade of KEK B-factory (KEKB). In the experiment, the pressure in a TiN-coated duct was measured and compared with that in a non-coated one. The TiN film (200 nm thick) was coated by DC magnetron sputtering at KEK. After an air exposure for the previously-determined period, the duct was evacuated by a turbo-molecular pump (300 l/s). At 50 hours after evacuation, the pressure was about 4 times larger than that for the case of the non-coated one. The residual gas was mainly water. In order to fine the minimum baking temperature to decrease the gas desorption from the TiN coating, the pressures were measured after the baking by changing the temperatures in the practical range, from 50 to 150 degrees. The pressure after the baking at 80 degrees was finally found to be comparable to that for the non-coated one. This paper describes these results in detail including the measurements of gas desorption rates.
KEK, Ibaraki
Crab cavities were installed at KEKB at the beginning of 2007. The beam operation with the crab cavities is in progress. In this paper, machine performance with crab crossing is described focusing on a specific luminosity and a beam lifetime issue related to the dynamic beam-beam effects.
KEK, Ibaraki
SLAC, Menlo Park, California
Funding: The Japan/US Cooperation Program
Beam instability caused by the electron cloud is expected to be a limiting factor in the performance of future advanced positron and proton storage rings. In a wiggler section of the positron ring of the KEK B-factory (KEKB), we have installed a vacuum chamber with an insertion that can be replaced and including different techniques to study the mitigation of the electron-cloud effect in a high magnetic field region. We have installed an insertion with strip-line clearing electrode, an insertion with triangular grooves and an insertion with a smooth surface, and compared them each other under the same conditions. The electrode insertion is composed of a thin tungsten layer formed on a thin alumina ceramic layer. The groove insertion is composed of TiN-coated triangular grooves running longitudinally. In this paper, we report about the tests in the KEKB and about the large reduction in the measured electron cloud density when the clearing electrode and groove sections are installed with respect to the smooth insertion. These experiments are the first ones demonstrating the principle of the clearing electrode and groove insertions in a magnetic field.
SLAC, Menlo Park, California
KEK, Ibaraki
Using a streak camera, we measured the longitudinal profiles of a positron bunch in the Low Energy Ring (LER) of KEKB at various currents. The measured charge densities were used to construct a simple Q=1 broadband impedance model. The model with three parameters not only gave an excellent description of longitudinal dynamics for a positive momentum compaction factor but also for the negative ones, including bunch shortening bellow a threshold and bursting modes beyond the threshold. Furthermore, our study indicated that the threshold of microwave instability was about 0.5 mA in bunch current in the LER. At the nominal operating current 1.0 mA, there was a 20% increase of the energy spread. The results of measurement, analysis, and simulations will be presented in this paper.
CLASSE, Ithaca, New York
LBNL, Berkeley, California
KEK, Ibaraki
SLAC, Menlo Park, California
Funding: Work supported by the National Science Foundation, the US Department of Energy, and the Japan/US Cooperation Program
Wiggler magnets are one of the key components in the ILC Damping Ring. It is critical to the ILCDR GDE to understand electron cloud (EC) growth and patterns, and to develop EC suppression techniques in the wiggler beampipes. The CESR-c superconducting wigglers, closely matching the parameters of the ILCDR wigglers, serve as unique testing vehicles. As part of the CesrTA project, we replaced the copper beampipes of two SCWs with EC diagnostic beampipes, where one of the beampipes is uncoated and the second is coated with a thin TiN film. Each of the EC diagnostic beampipes is equipped with three retarding field analyzers (RFAs) at strategic longitudinal locations in the wiggler field. Each of the RFAs has 12-fold segmentation to measure the horizontal EC density distribution. To maintain sufficient vertical beam aperture and to fit within the SCW warm bore, a thin style of RFA (with a thickness of 2.5 mm) has been developed and deployed. These SCWs with RFA-equipped beampipe have been installed and successfully operated in the re-configured CesrTA vacuum system. This paper describes the design and the construction of the RFA-equipped SCW beampipes and operational experience.
CLASSE, Ithaca, New York
LBNL, Berkeley, California
KEK, Ibaraki
ANL, Argonne
Fermilab, Batavia
CalPoly, San Luis Obispo, CA
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire
SLAC, Menlo Park, California
Cornell University, Ithaca, New York
Cockcroft Institute, Warrington, Cheshire
Funding: Support provided by the US National Science Foundation, the US Department of Energy, and the Japan/US Cooperation Program.
In March of 2008, the Cornell Electron Storage Ring (CESR) concluded twenty eight years of colliding beam operations for the CLEO high energy physics experiment. We have reconfigured CESR as an ultra low emittance damping ring for use as a test accelerator (CesrTA) for International Linear Collider (ILC) damping ring R&D. The primary goals of the CesrTA program are to achieve a beam emittance approaching that of the ILC Damping Rings with a positron beam, to investigate the interaction of the electron cloud with both low emittance positron and electron beams, to explore methods to suppress the electron cloud, and to develop suitable advanced instrumentation required for these experimental studies (in particular a fast x-ray beam size monitor capable of single pass measurements of individual bunches). We report on progress with the CESR conversion activities, the status and schedule for the experimental program, and the first experimental results that have been obtained.
CLASSE, Ithaca, New York
LBNL, Berkeley, California
ANL, Argonne
KEK, Ibaraki
SLAC, Menlo Park, California
Funding: Supported by the US National Science Foundation, the US Department of Energy under Contracts No. DE-AC02-06CH11357, DE-AC02-05CH11231, and DE-AC02-76SF00515, and by the Japan/US Cooperation Program.
CESR at Cornell has been operating as a damping ring test accelerator (CesrTA) with beam parameters approaching those anticipated for the ILC damping rings. A core component of the research program is to fully understand electron cloud effects in CesrTA. As a local probe of the electron cloud, several segmented retarding field analyzers (RFAs) have been installed in CesrTA in dipole, drift and wiggler regions. Using these RFAs, the energy spectrum of the time-average electron cloud current density striking the walls has been measured for a variety of bunch train patterns; with bunch populations up to 2x1010 per bunch, beam energies from 2 to 5 GeV, horizontal geometric emittances from roughly 10 to 133 nm, and bunch lengths of about 1 cm; and for both positron and electron beams. The effect of mitigation measures, such as coatings, has also been studied. This paper will compare these measurements with the predictions of simulation programs, and discuss the implications of these comparisons for our understanding of the physics of electron cloud generation and mitigation in ILC-like damping rings.