| Paper | Title | Page |
|---|---|---|
| MO6RFP079 | Improved DC Gun Insulator | 557 |
|
||
|
Funding: Supported in part by USDOE Contract No. DE-AC05-84-ER-40150. Many user facilities such as synchrotron light sources and free electron lasers require accelerating structures that support electric fields of 10-100 MV/m, especially at the start of the accelerator chain where ceramic insulators are used for very high gradient DC guns. These insulators are difficult to manufacture, require long commissioning times, and have poor reliability, in part because energetic electrons bury themselves in the ceramic, creating a buildup of charge and causing eventual puncture. A novel ceramic manufacturing process is proposed. It will incorporate bulk resistivity in the region where it is needed to bleed off accumulated charge caused by highly energetic electrons. This process will be optimized to provide an appropriate gradient in bulk resistivity from the vacuum side to the air side of the HV standoff ceramic cylinder. A computer model will be used to determine the optimum cylinder dimensions and required resistivity gradient for an example RF gun application. A ceramic material example with resistivity gradient appropriate for use as a DC gun insulator will be fabricated by glazing using doping compounds and tested. |
||
| WE5PFP043 | Beam Pipe HOM Absorber for 750 MHz RF Cavities | 2092 |
|
||
|
Funding: Supported in part by USDOE Contract. DE-AC05-84-ER-40150 Superconducting HOM-damped (higher-order-mode-damped) RF systems are needed for present and future storage ring and linac applications. Superconducting RF (SRF) systems typically contain unwanted frequencies or higher order modes (HOM) that must be absorbed by ferrite and other lossy ceramic-like materials that are brazed to substrates mechanically attached to the drift tubes adjacent to the SRF cavity. These HOM loads must be thermally and mechanically robust and must have the required broadband microwave loss characteristics, but the ferrites and their attachments are weak under tensile stresses and thermal stresses and tend to crack. A HOM absorber with improved materials and design will be developed for high-gradient 750 MHz superconducting cavity systems. RF system designs will be numerically modeled to determine the optimum ferrite load required to meet the broadband loss specifications. Several techniques for attaching ferrites to the metal substrates will be studied, including full compression rings and nearly-stress-free ferrite assemblies. Prototype structures will be fabricated and tested for mechanical strength. |
||
| TU5PFP020 | Doped H2-Filled RF Cavities for Muon Beam Cooling | 855 |
|
||
|
Funding: Supported in part by USDOE STTR Grant DE-FG02-08ER86350 and and FRA DOE contract number DE-AC02-07CH11359 RF cavities pressurized with hydrogen gas may provide effective muon beam ionization cooling needed for muon colliders. Recent 805 MHz test cell studies reported below include the first use of SF6 dopant to reduce the effects of the electrons that will be produced by the ionization cooling process in hydrogen or helium. Measurements of maximum gradient in the Paschen region are compared to a simulation model for a 0.01% SF6 doping of hydrogen. The observed good agreement of the model with the measurements is a prerequisite to the investigation of other dopants. |
||
| WE5PFP008 | RF Breakdown of Metallic Surfaces in Hydrogen | 2000 |
|
||
|
Funding: Supported in part by USDOE STTR Grant DE-FG02-08ER86350 Supported in part by USDOE STTR Grant DE-FG02-08ER86352 and in part by FRA DOE contract number DE-AC02-07CH11359 In earlier reports, microscopic images of the surfaces of metallic electrodes used in high-pressure gas-filled 805 MHz RF cavity experiments were used to investigate the mechanism of RF breakdown of tungsten, molybdenum, and beryllium electrode surfaces. Plots of remnants were consistent with the breakdown events being due to field emission, due to the quantum mechanical tunnelling of electrons through a barrier as described by Fowler and Nordheim. In the work described here, these studies have been extended to include tin, aluminium, and copper. Contamination of the surfaces, discovered after the experiments concluded, have cast some doubt on the proper qualities to assign to the metallic surfaces. However, two significant results are noted. First, the maximum stable RF gradient of contaminated copper electrodes is higher than for a clean surface. Second, the addition of as little as 0.01% of SF6 to the hydrogen gas increased the maximum stable gradient, which implies that models of RF breakdown in hydrogen gas will be important to the study of metallic breakdown |
||
| WE5PFP009 | RF Breakdown Studies Using a 1.3-GHz Test Cell | 2003 |
|
||
|
Funding: Supported in part by USDOE STTR Grant DE-FG02-08ER86352 and FRA DOE contract number DE-AC02-07CH11359 Many present and future particle accelerators are limited by the maximum electric gradient and peak surface fields that can be realized in RF cavities. Despite considerable effort, a comprehensive theory of RF breakdown has not been achieved and mitigation techniques to improve practical maximum accelerating gradients have had only limited success. Recent studies have shown that high gradients can be achieved quickly in 805 MHz RF cavities pressurized with dense hydrogen gas without the need for long conditioning times, because the dense gas can dramatically reduce dark currents and multipacting. In this project we use this high pressure technique to suppress effects of residual vacuum and geometry found in evacuated cavities to isolate and study the role of the metallic surfaces in RF cavity breakdown as a function of magnetic field, frequency, and surface preparation. A 1.3-GHz RF test cell with replaceable electrodes (e.g. Mo, Cu, Be, W, and Nb) and pressure barrier capable of operating both at high pressure and in vacuum been designed and built, and preliminary testing has been completed. A series of detailed experiments is planned at the Argonne Wakefield Accelerator. |