| Paper | Title | Page |
|---|---|---|
| MO6RFP080 | Intense Stopping Muon Beams | 560 |
|
||
|
The study of rare processes using a beam of muons that stop in a target provides access to new physics at and beyond the reach of energy frontier colliders. The flux of stopping muons is limited by the pion production process and by stochastic processes in the material used to slow down the decay muons. Innovative muon beam collection and cooling techniques are applied to the design of stopping muon beams in order to provide better beams for such experiments. Such intense stopping beams will also support the development of applications such as muon spin resonance and muon-catalyzed fusion. |
||
| TU5PFP017 | RF Cavities Loaded with Dielectric for Muon Facilities | 846 |
|
||
|
Funding: Supported in part by FRA DOE contract number DE-AC02-07CH11359 RF cavities below 800 MHz are large, so alternative cavities at low frequencies are needed. Novel dielectric loaded RF cavities will allow smaller diameter cavities to be designed; changing the frequency of a cavity design would be as simple as changing the dielectric cylinder insert material or inner radius of the dielectric in the cavity. This paper discusses RF cavities loaded with dielectric material that could be used in various ways for muon facilities. The examples given are for 400 and 800 MHz cavities. Our initial motivation was to use dielectric to reduce the radial size of gas-filled cavities in helical cooling channels, but dielectric-loading has potential use in vacuum cavities for suppression of dark current emission. We also studied cavities that can be used for the phase rotation channel in the front end of a muon collider or neutrino factory. |
||
| TU5PFP018 | Tunable RF Cavities Using Orthogonally Biased Ferrite | 849 |
|
||
|
Funding: Supported by STTR Grant DE-FG02-07ER86320 and FRA DOE contract number DE-AC02-07CH11359 Originally conceived as a solution for FFAG applications, a new compact RF cavity design that tunes rapidly over various frequency ranges can be used to upgrade existing machines. The design being developed uses orthogonally biased garnet cores for fast frequency tuning and liquid dielectric to adjust the frequency range and to control the core temperature. We describe measurements of candidate ferrite and dielectric materials. The first use of the new cavity concept will be for improvements to the 8 GeV Fermilab Booster synchrotron. |
||
| TU5PFP019 | Phase and Frequency Locked Magnetrons for SRF Sources | 852 |
|
||
|
Funding: Supported in part by USDOE Contract. DE-AC05-84-ER-40150 and by FRA DOE contract number DE-AC02-07CH11359 Magnetrons are low-cost highly-efficient microwave sources, but they have several limitations, primarily centered about the phase and frequency stability of their output. When the stability requirements are low, such as for medical accelerators or kitchen ovens, magnetrons are the very efficient power source of choice. But for high energy accelerators, because of the need for frequency and phase stability–-proton accelerators need 1-2 degrees source phase stability, and electron accelerators need .1-.2 degrees of phase stability–-they have rarely been used. We describe a novel variable frequency cavity technique which will be utilized to phase and frequency lock magnetrons. |
||
| TU5PFP020 | Doped H2-Filled RF Cavities for Muon Beam Cooling | 855 |
|
||
|
Funding: Supported in part by USDOE STTR Grant DE-FG02-08ER86350 and and FRA DOE contract number DE-AC02-07CH11359 RF cavities pressurized with hydrogen gas may provide effective muon beam ionization cooling needed for muon colliders. Recent 805 MHz test cell studies reported below include the first use of SF6 dopant to reduce the effects of the electrons that will be produced by the ionization cooling process in hydrogen or helium. Measurements of maximum gradient in the Paschen region are compared to a simulation model for a 0.01% SF6 doping of hydrogen. The observed good agreement of the model with the measurements is a prerequisite to the investigation of other dopants. |
||
| TU5PFP021 | Traveling Wave RF Systems for Helical Cooling Channels | 858 |
|
||
|
Funding: supported in part by USDOE STTR Grant DE-FG02-08ER86350 The great advantage of the helical ionization cooling channel (HCC) is its compact structure that enables the fast cooling of muon beam 6-dimensional phase space. This compact aspect requires a high average RF gradient, with few places that do not have cavities. Also, the muon beam is diffuse and requires an RF system with large transverse and longitudinal acceptance. A traveling wave system can address these requirements. First, the number of RF power coupling ports can be significantly reduced compared with our previous pillbox concept. Secondly, by adding a nose on the cell iris, the presence of thin metal foils traversed by the muons can possibly be avoided. We show simulations of the cooling performance of a traveling wave RF system in a HCC, including cavity geometries with inter-cell RF power couplers needed for power propagation. |
||
| TU6PFP062 | Preparations for Muon Experiments at Fermilab | 1427 |
|
||
|
Funding: Operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy. The use of existing Fermilab facilities to provide beams for two muon experiments –- the Muon to Electron Conversion Experiment (Mu2e) and the Muon g-2 Experiment –- is under consideration. Plans are being pursued to be able to perform these experiments following the completion of the Tevatron Collider Run II with no impact to the on-going Main Injector neutrino program by using spare Booster cycles to provide 8.9 GeV/c protons on target. Utilizing the beam lines and storage rings used today for antiproton accumulation, beams can be prepared for these experiments with minimal disruption, reconfiguration or expansion of the Fermilab accelerator infrastructure. The proposed operational scenarios and required alterations to the complex are described. |
||
| WE5PFP008 | RF Breakdown of Metallic Surfaces in Hydrogen | 2000 |
|
||
|
Funding: Supported in part by USDOE STTR Grant DE-FG02-08ER86350 Supported in part by USDOE STTR Grant DE-FG02-08ER86352 and in part by FRA DOE contract number DE-AC02-07CH11359 In earlier reports, microscopic images of the surfaces of metallic electrodes used in high-pressure gas-filled 805 MHz RF cavity experiments were used to investigate the mechanism of RF breakdown of tungsten, molybdenum, and beryllium electrode surfaces. Plots of remnants were consistent with the breakdown events being due to field emission, due to the quantum mechanical tunnelling of electrons through a barrier as described by Fowler and Nordheim. In the work described here, these studies have been extended to include tin, aluminium, and copper. Contamination of the surfaces, discovered after the experiments concluded, have cast some doubt on the proper qualities to assign to the metallic surfaces. However, two significant results are noted. First, the maximum stable RF gradient of contaminated copper electrodes is higher than for a clean surface. Second, the addition of as little as 0.01% of SF6 to the hydrogen gas increased the maximum stable gradient, which implies that models of RF breakdown in hydrogen gas will be important to the study of metallic breakdown |
||
| WE5PFP009 | RF Breakdown Studies Using a 1.3-GHz Test Cell | 2003 |
|
||
|
Funding: Supported in part by USDOE STTR Grant DE-FG02-08ER86352 and FRA DOE contract number DE-AC02-07CH11359 Many present and future particle accelerators are limited by the maximum electric gradient and peak surface fields that can be realized in RF cavities. Despite considerable effort, a comprehensive theory of RF breakdown has not been achieved and mitigation techniques to improve practical maximum accelerating gradients have had only limited success. Recent studies have shown that high gradients can be achieved quickly in 805 MHz RF cavities pressurized with dense hydrogen gas without the need for long conditioning times, because the dense gas can dramatically reduce dark currents and multipacting. In this project we use this high pressure technique to suppress effects of residual vacuum and geometry found in evacuated cavities to isolate and study the role of the metallic surfaces in RF cavity breakdown as a function of magnetic field, frequency, and surface preparation. A 1.3-GHz RF test cell with replaceable electrodes (e.g. Mo, Cu, Be, W, and Nb) and pressure barrier capable of operating both at high pressure and in vacuum been designed and built, and preliminary testing has been completed. A series of detailed experiments is planned at the Argonne Wakefield Accelerator. |