INFN/LNF, Frascati (Roma)
SLAC, Menlo Park, California
CERN, Geneva
BINP SB RAS, Novosibirsk
KEK, Ibaraki
University of Pisa and INFN, Pisa
The SuperB project aims at the construction of an asymmetric (4x7 GeV), very high luminosity, B-Factory on the Roma II (Italy) University campus. The luminosity goal of 1036 cm-2 s-1 can be reached with a new collision scheme with large Piwinski angle and the use of “crab” sextupoles. A crab-waist IR has been successfully tested at the DAPHNE Phi-Factory at LNF-Frascati (Italy) in 2008. The crab waist together with very low beta* will allow for operation with relatively low beam currents and reasonable bunch length, comparable to those of PEP-II and KEKB. In the High Energy Ring, two spin rotators permit bringing longitudinally polarized beams into collision at the IP. The lattice has been designed with a very low intrinsic emittance and is quite compact, less than 2 km long. The tight focusing requires a sophisticated Interaction Region with quadrupoles very close to the IP. A Conceptual Design Report was published in March 2007, and beam dynamics and collective effects R&D studies are in progress in order to publish a Technical Design Report by the end of 2010. A status of the design and simulations is presented in this paper.
SLAC, Menlo Park, California
Funding: Work supported by the U.S. Department of Energy under contract number DE-AC02-76SF00515
SLAC National Accelerator Laboratory is studying an option of building a high brightness synchrotron light source machine, PEP-X, in the existing PEP-II tunnel*,**. By replacing 6 arcs of FODO cells of PEPII High Energy Ring (HER) with two arcs of DBA and four arcs of TME and installation of 89.3 m long damping wiggler an ultra low beam emittance of 0.14 nm-rad (including intra-beam scattering) at 4.5 GeV is achieved. In this paper we study the possibility to further reduce the beam emittance by releasing the constraint of the dispersion free in the DBA straight. The QBA (Quadruple Bend Achromat) cell is used to replace the DBA. The ratio of outer and inner bending angle is optimized. The dispersion function in the non-dispersion straight is controlled to compromise with lower emittance and beam size at the dispersion straight. An undulator of period length 23 mm, maximum magnetic field of 1.053 T, and total periods of 150 is used to put in the 30 straights to simulate the effects of these IDs on the beam emittance and energy spread. The brightness including all the ID effects is calculated and compared to the original PEP-X design.
*R. Hettel et al., “Ideas for a Future PEP-X Light Source”, EPAC08, p.2031(2008).
**M-H Wang et al., “Lattice Design of PEP-X as a Light Source Machine at SLAC”, EPAC08, p.2127(2008).
SLAC, Menlo Park, California
Funding: This work is supported by the Department of Energy contract DE-AC02-76SF00515.
LCLS capabilities can be significantly extended with a second undulator aiming at the soft x-ray spectrum (1- 5 nm). To allow for simultaneous hard and soft x-ray operations, 14 GeV beams at the end of the LCLS accelerator can be intermittently switched into the SLAC A-line (the beam transport line to End Station A) where the second undulator may be located. In this paper, we discuss the A-line optics design for transporting the high-brightness LCLS beams using the existing tunnel. To preserve the high brightness of the LCLS beams, special attentions are paid to effects of incoherent and coherent synchrotron radiation. Start-to-end simulations using realistic LCLS beam distributions are carried out.
SLAC, Menlo Park, California
INFN/LNF, Frascati (Roma)
BINP SB RAS, Novosibirsk
The proposed SuperB factory will provide longitudinal polarized electrons to the experiment. Vertically polarized electrons will be injected into the High Energy Ring; the vertical spin orientation will be locally rotated into the longitudinal direction before the interaction point and back afterwards to avoid spin depolarization. The spin rotators can be designed using compensated solenoids–-as proposed by Zholents and Litvinenko–-to rotate the spin into the horizontal plane, followed by dipoles for horizontal spin rotation into the longitudinal direction. Such spin rotators have been matched into the existing lattice and combined with the crab-waist IR. Several ways of achieving this are explored, that differ in the degree of spin matching achieved and the overall geometry of the interaction region. The spin rotation can also be achieved by a series of dipole magnets only, which present a different optical matching problem. We will compare the different scenarios leading up to the adopted solution.
SLAC, Menlo Park, California
Funding: This work is supported by the Department of Energy contract DE-AC02-76SF00515.
FACET is a proposed facility at SLAC National Accelerator Laboratory for beam driven plasma wakefield acceleration research. It is proposed to be built in the SLAC linac sector 20, where it will be separated from the LCLS located downstream and will gain the maximum beam energy from the upstream two kilometers of linac. FACET will also include an upgrade to linac sector 10, where a new e+ compressor chicane will be installed. The sector 20 will require a new optics consisting of two chicanes for e+ and e- bunch length compression, a final focus system and an extraction line. The two chicanes will allow the transport of e- and e+ bunches together, their simultaneous compression and proper positioning of e+ bunch behind e- at the plasma Interaction Point (IP). For a minimal cost, the new optics will mostly use the existing SLAC magnets. The desired beam parameters at the IP are: up to 23 GeV beam energy, 2·1010 charge per bunch, 10 micron round beam spot without dispersion and 25 micron bunch length. Details of the FACET optics design and results of particle tracking simulations are presented.
SLAC, Menlo Park, California
Stanford University, Stanford, California
UCLA, Los Angeles, California
Funding: This work was supported by the Director, Office of Science, Office of Basic Energy Sciences, of the U.S. Department of Energy under Contract No. DE-AC02-76SF00515.
SSRL and SLAC groups are developing a long-range plan to transfer its evolving scientific programs from the SPEAR3 light source to a much higher performing photon source that would be housed in the 2.2-km PEP-II tunnel. While various concepts for the PEP-X light source are under consideration, including ultimate storage ring and ERL configurations, the present baseline design is a very low-emittance storage ring. A hybrid lattice has DBA or QBA cells in two of the six arcs that provide a total ~30 straight sections for ID beam lines extending into two new experimental halls. The remaining arcs contain TME cells. Using ~100 m of damping wigglers the horizontal emittance at 4.5 GeV would be ~0.1 nm-rad with >1 A stored beam. PEP-X will produce photon beams having brightnesses near 1022 at 10 keV. Studies indicate that a ~100-m undulator could have FEL gain and brightness enhancement at soft x-ray wavelengths with the stored beam. Crab cavities or other beam manipulation systems could be used to reduce bunch length or otherwise enhance photon emission properties. The present status of the PEP-X lattice and beam line designs are presented and other implementation options are discussed.
SLAC, Menlo Park, California
Funding: Work supported by the DOE under contract DE-AC02-76SF00515.
Facilities for Accelerator Science and Experimental Test Beams (FACET) is a proposed facility at SLAC that would use the initial two-thirds of the linac to transport e+ and e- beams to an experimental region. A principal use of this facility is to identify the optimum method for accelerating positrons in a beam driven plasma wakefield accelerator. To study this, a positron bunch, followed ½ an rf cycle later by an electron bunch, will be accelerated to an asymmetric chicane designed to move the positrons behind the electrons, and then on to the plasma wakefield test stand. A major focus of study was the coupling of jitter of the positron bunch to the electron bunch via linac wakes. Lucretia is a Matlab toolbox for the simulation of electron beam transport systems, capable of multi-bunch tracking and wakefield calculations. With the exception of the lack of support for tracking of electrons and positrons within a single bunch train, it was well suited to the jitter coupling studies. This paper describes the jitter studies, including modifications made to Lucretia to correctly simulate tracking of mixed-species bunch trains through a lattice of magnetic elements and em wakes.