KEK, Ibaraki
IN2P3-LAPP, Annecy-le-Vieux
ICEPP, Tokyo
University of Tokyo, Tokyo
The ATF2, accelerator test facility has been developed confirming techniques for obtaining super low emittance beam for future particle accelerators. Here, the converged beam size is designed to be 37 nm, and a precision beam size monitor using interference fringes as a reference called Shintake monitor is used for measuring it. In order to measure the beam size with resolution of better than 10%, relative position between the beam and the interference fringes should be stabilized within few nanometers. Highly rigid tables and mounts for the Shintake monitor and final focusing magnets are adopted with highly rigid floor to ensure relative position stability. Then, the Shintake monitor can be stabilized against the beam, since the beam fluctuates coherently with the final focusing magnets. On the other hand the interference fringes are stabilized against the Shintake monitor with precise phase control system. As a result, relative position between the beam and the interference fringes is stabilized based on rigidity of tables, mounts, and floor between them. We will present our conception for stabilization and results of vibration measurements for the Shintake monitor.
IN2P3-LAPP, Annecy-le-Vieux
ICEPP, Tokyo
KEK, Ibaraki
University of Tokyo, Tokyo
Funding: Work supported by the Agence Nationale de la Recherche of the French Ministry of Research (Programme Blanc, Project ATF2-IN2P3-KEK, contract ANR-06-BLAN-0027).
Future linear collider projects like ILC and CLIC will have beam sizes of a few nm. Vibration sources like ground motion can hamper the beam collisions. Relative jitter tolerance between the final focus magnets and the Interaction point (IP) is a fraction of the beam size. The ATF2 project proposes a test facility with a projected beam of 37nm. To measure the beam size with only 2% of error, vertical relative jitter tolerance (above 0.1Hz) between the final doublet magnets (FD) and the IP (with a Shintake beam Size Monitor: BSM) is of the order of 7nm while ground motion is of about 150nm. Thanks to determined adequate instrumentations, investigations were done to design supports for FD. Since ground motion measurements showed that this one is coherent up to 4m, more than the distance between FD and BSM, we chose a stiff support for FD fixed to the ground on its entire surface. Thus, FD and BSM should move in a coherent way. Vibration measurements show that relative motion between FD and BSM is only of 4.8nm and that flowing water in FD does not add any significant jitter. The FD support has been consequently validated on site at ATF2 to be within the vibration specifications.
IHEP Beijing, Beijing
JAI, Egham, Surrey
KEK, Ibaraki
ICEPP, Tokyo
SLAC, Menlo Park, California
University of Tokyo, Tokyo
Funding: NSFC 10525525 and 10775154. CNRS-IN2P3 and ANR.
The ATF2 project is the final focus system prototype for ILC and CLIC linear collider projects, with a purpose to reach a 37nm vertical beam size at the interaction point. We report on techniques developed based on simulation studies to adjust the horizontal and vertical beam waists independently in the presence of errors, at two different IP locations where the beam size can be measured with different accuracies. During initial commissioning, we will start with larger than nominal β-functions at the IP, to reduce the effects from higher-order optical aberrations and thereby simplify the optical corrections needed. The first measurements in such intermediate β-configurations are reported.
University of Tokyo, Tokyo
KEK, Ibaraki
ICEPP, Tokyo
Commissioning of the ATF/ATF2 project will start in the winter of 2008 to 2009, with the aim of studying beam optics, diagnostic instrumentations, and tuning processes for around 35 nm beam size. The project is the realistic scaled down model of the ILC final focus system, and also, studies in the project offered important findings for future accelerator physics. In this presentation, we will present about the status of the first commissioning of the Shintake monitor for ATF2. The monitor is located at the virtual interaction point of the ATF2 (the focus point) to measure beam size. A measurable ranges as a design are from 6 micron down to 20 nm in vertical and down to several microns in horizontal. That wide range allows us to used the detector from the beginning of the beam tuning process. The monitor scheme was originally proposed by T. Shintake and verified using around 60 nm beam at FFTB project. We upgraded the detector system for ATF2 of smaller beam size and implemented a laser wire scheme for horizontal beam size measurement. These additional capabilities are also presented.
SLAC, Menlo Park, California
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire
JAI, Oxford
KEK, Ibaraki
IHEP Beijing, Beijing
LAL, Orsay
Royal Holloway, University of London, Surrey
IN2P3-LAPP, Annecy-le-Vieux
OXFORDphysics, Oxford, Oxon
ATOMKI, Debrecen
CERN, Geneva
DESY, Hamburg
Fermilab, Batavia
Kyungpook National University, Daegu
PAL, Pohang, Kyungbuk
Kyoto ICR, Uji, Kyoto
ICEPP, Tokyo
University of Tokyo, Tokyo
UCL, London
BNL, Upton, Long Island, New York
Tohoku University, Graduate School of Science, Sendai
UMAN, Manchester
Hiroshima University, Graduate School of Science, Higashi-Hiroshima
Cockcroft Institute, Warrington, Cheshire
ATF2 is a final-focus test beam line that attempts to focus the low-emittance beam from the ATF damping ring to a beam size of about 37 nm, and at the same time to demonstrate nm beam stability, using numerous advanced beam diagnostics and feedback tools. The construction is well advanced and beam commissioning of ATF2 has started in the second half of 2008. ATF2 is constructed and commissioned by ATF international collaborations with strong US, Asian and European participation.
