KEK, Ibaraki
JAEA/ERL, Ibaraki
The compact ERL, cERL, is a project to test an energy recovery linac (ERL) with 60 MeV and 100 mA electron beam to generate synchrotron radiation with smaller emittance and shorter pulse length. The design work of the cERL injector has been carried out using a space charge simulation code. The injector consists of 500 kV photo cathode DC gun, two solenoid magnets, buncher cavity, three super conducting RF cavities and merger section to return pass. It generates an electron beam with -77 pC bunch charge and 1.3 GHz repetition rate. Our target value of emittance is less than 1 mm mrad with the bunch length of 1 mm at the exit of the injector. The parameter optimization of the injector using the multi objected method has been carried out to obtain the minimum emittance. The simulation results will be presented in detail.
JAEA/FEL, Ibaraki-ken
KEK, Ibaraki
JAEA/ERL, Ibaraki
HU/AdSM, Higashi-Hiroshima
Nagoya University, Nagoya
A 500-kV, 10-mA photocathode DC gun has been designed and is now under fabrication by the collaboration efforts of JAEA, KEK, Hiroshima Univ. and Nagoya Univ. The Cockcroft-Walton generator and the ceramic insulator are installed upright in the SF6 tank. We have adopted a multiple-stacked cylindrical ceramic insulator, because this type of ceramic insulator has shown good stability and robustness at the 200-kV Nagoya polarized gun and the 250-kV JAEA FEL gun. All the vacuum chambers are made of titanium alloy with very low out-gassing. The Cockcroft-Walton generator, the ceramic insulator, the vacuum chambers will be fabricated by April 2009 and a high-voltage test will be started soon later. Up-to-date status of the gun development will be presented in detail.
JAEA/ERL, Ibaraki
KEK, Ibaraki
A 250-kV, 50-mA electron gun has been developed at JAEA for establishing fundamental technologies to generate and evaluate a ultra-small emittance beam, which is required for future ERLs such as a coherent X-ray source and a high-flux gamma-ray source. The gun has been assembled and the first photo-current was obtained from a cathode of NEA-GaAs. Apparatuses for beam measurements has been installed. We plan to measure the transverse emittance by a double-slit configuration and the temporal profile with a deflecting cavity.
KEK, Ibaraki
Future accelerators require a high resolution beam profile monitor that measures the beam non-destructively and works at high beam intensity. Laser based beam monitors can be the solution. It uses a focused laser beam to scan the electron beam while detecting the Compton scattered photon. Accelerator Test Facility at KEK has been developing various types of Laser Wire monitors. CW laser wire with build-up optical cavity has been used to measure the small emittance beam at the damping ring. Pulsed laser wire has been developed to measure a small focused beam at the extraction line. Performance of these systems will be presented.
RISE, Tokyo
KEK, Ibaraki
Kyoto University, Kyoto
Funding: Work supported by a Grant-In-Aid for Creative Scientific Research of JSPS (KAKENHI 17GS0210) and a Grant-In-Aid for JSPS Fellows (19-5789)
We have been developing a pulsed-laser storage technique in a super-cavity for compact X-ray sources. The pulsed-laser super-cavity enables to make high peak power and small waist laser at the collision point with the electron beam. Recently, using 357 MHz mode-locked Nd:VAN laser pulses which stacked in a super-cavity scattered off a multi-bunch electron beam, we obtained multi-pulse X-rays through laser-Compton scattering. Detecting an X-ray pulse-by-pulse using a high-speed detector makes it possible to measure the 3-dimensional beam size with bunch-by-bunch scanning the laserwire target position and pulse timing. This technique provides not only the non-destructive beam profile monitoring but also the measuring of bunch length and/or bunch spacing shifting. In our multi-bunch electron linac, the bunch spacing narrowing due to the electron velocity difference in the train at the output of rf-gun cavity was observed. The principle of the 3-dimensional laserwire monitor and the experimental results of multi-bunch electron beam measurements will be presented at the conference.
CERN, Geneva
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire
IHEP Beijing, Beijing
LAL, Orsay
KEK, Ibaraki
UMAN, Manchester
SLAC, Menlo Park, California
The CLIC Final Focus System has considerably larger chromaticity than those of ILC and its scaled test machine ATF2. We propose to reduce the IP betas of ATF2 to reach a CLIC-like chromaticity. This would also allow to study the FFS tuning difficulty as function of the IP beam spot size. Both the ILC and CLIC projects will largely benefit from the ATF2 experience at these ultra-low IP betas.
KEK, Ibaraki
JAEA/ERL, Ibaraki
JASRI/SPring-8, Hyogo-ken
ISSP/SRL, Chiba
UVSOR, Okazaki
HU/AdSM, Higashi-Hiroshima
Hiroshima University, Graduate School of Science, Higashi-Hiroshima
AIST, Tsukuba
Future synchrotron light source project using an energy recovery linac (ERL) is under proposal at the High Energy Accelerator Research Organization (KEK) in collaboration with several Japanese institutes such as the JAEA and the ISSP. We are on the way to develop such key technologies as the super-brilliant DC photo-injector and superconducting cavities that are suitable for both CW and high-current operations. We are also promoting the construction of the Compact ERL for demonstrating such key technologies. We report the latest status of our project, including update results from our photo-injector and from both superconducting cavities for the injector and the main linac, as well as the progress in the design and preparations for constructing the Compact ERL.
Kyungpook National University, Daegu
Royal Holloway, University of London, Surrey
KEK, Ibaraki
PAL, Pohang, Kyungbuk
UCL, London
SLAC, Menlo Park, California
Fermilab, Batavia
CHEP, Daegu
University of Cambridge, Cambridge
The ATF2 international collaboration is intending to demonstrate nanometer beam sizes required for the future Linear Colliders. The position of the electron beam focused down at the end of the ATF2 extraction line to a size as small as 35 nm has to be measured with nanometer resolution. For that purpose a special Interaction Point(IP) beam position monitor (BPM) was designed. In this paper we report on the features of the BPM and electronics design providing the required resolution. We also consider the results obtained with BPM triplet which was installed in the ATF beamline and the first data from ATF2 commissioning runs.
KEK, Ibaraki
IN2P3-LAPP, Annecy-le-Vieux
ICEPP, Tokyo
University of Tokyo, Tokyo
The ATF2, accelerator test facility has been developed confirming techniques for obtaining super low emittance beam for future particle accelerators. Here, the converged beam size is designed to be 37 nm, and a precision beam size monitor using interference fringes as a reference called Shintake monitor is used for measuring it. In order to measure the beam size with resolution of better than 10%, relative position between the beam and the interference fringes should be stabilized within few nanometers. Highly rigid tables and mounts for the Shintake monitor and final focusing magnets are adopted with highly rigid floor to ensure relative position stability. Then, the Shintake monitor can be stabilized against the beam, since the beam fluctuates coherently with the final focusing magnets. On the other hand the interference fringes are stabilized against the Shintake monitor with precise phase control system. As a result, relative position between the beam and the interference fringes is stabilized based on rigidity of tables, mounts, and floor between them. We will present our conception for stabilization and results of vibration measurements for the Shintake monitor.
RCNS, Sendai
KEK, Ibaraki
Tohoku University, School of Scinece, Sendai
We have designed a beam orbit tilt monitor for stabilizing a beam orbit in ATF2. Once we can measure a beam orbit tilt angle with high precision at one point, we can relate this data with the beam position profile at the focal point. This monitor is composed of a single rectangular cavity and waveguides to extract the signal. This monitor can measure the beam orbit tilt with a single cavity. We extract the signal of one basic resonance mode from the cavity. This electric field mode is perpendicular to the nominal beam axis, and is excited by beam tilt. The magnitude of extracted signal gives us the beam tilt data. According to our simulation, the expected sensitivity is about 30 nrad.
UCL, London
Royal Holloway, University of London, Surrey
Kyungpook National University, Daegu
KEK, Ibaraki
SLAC, Menlo Park, California
Fermilab, Batavia
University of Cambridge, Cambridge
The ATF2 international collaboration is intending to demonstrate nanometre beam sizes required for the future Linear Colliders. An essential part of the beam diagnostics needed to achieve this goal is the high resolution cavity beam position monitors (BPMs). In this paper we report on the S-band system installed in the final focus region of the new ATF2 extraction beamline. It only includes 4 BPMs, but they are mounted on the most critical final focus magnets squeezing the beam down to 35 nm. We discuss both the design and the first operational experience with the system.
Royal Holloway, University of London, Surrey
Kyungpook National University, Daegu
KEK, Ibaraki
UCL, London
SLAC, Menlo Park, California
Fermilab, Batavia
University of Cambridge, Cambridge
The ATF2 international collaboration is intending to demonstrate nanometre beam sizes required for the future Linear Colliders. An essential part of the beam diagnostics needed to achieve that goal is the high resolution cavity beam position monitors (BPMs). In this paper we report on the C-band system consisting of 32 BPMs spread over the whole length of the new ATF2 extraction beamline. We discuss the design of the BPMs and electronics, main features of the DAQ system, and the first operational experience with these BPMs.
University of Tokyo, Tokyo
KEK, Ibaraki
ICEPP, Tokyo
Commissioning of the ATF/ATF2 project will start in the winter of 2008 to 2009, with the aim of studying beam optics, diagnostic instrumentations, and tuning processes for around 35 nm beam size. The project is the realistic scaled down model of the ILC final focus system, and also, studies in the project offered important findings for future accelerator physics. In this presentation, we will present about the status of the first commissioning of the Shintake monitor for ATF2. The monitor is located at the virtual interaction point of the ATF2 (the focus point) to measure beam size. A measurable ranges as a design are from 6 micron down to 20 nm in vertical and down to several microns in horizontal. That wide range allows us to used the detector from the beginning of the beam tuning process. The monitor scheme was originally proposed by T. Shintake and verified using around 60 nm beam at FFTB project. We upgraded the detector system for ATF2 of smaller beam size and implemented a laser wire scheme for horizontal beam size measurement. These additional capabilities are also presented.
SLAC, Menlo Park, California
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire
JAI, Oxford
KEK, Ibaraki
IHEP Beijing, Beijing
LAL, Orsay
Royal Holloway, University of London, Surrey
IN2P3-LAPP, Annecy-le-Vieux
OXFORDphysics, Oxford, Oxon
ATOMKI, Debrecen
CERN, Geneva
DESY, Hamburg
Fermilab, Batavia
Kyungpook National University, Daegu
PAL, Pohang, Kyungbuk
Kyoto ICR, Uji, Kyoto
ICEPP, Tokyo
University of Tokyo, Tokyo
UCL, London
BNL, Upton, Long Island, New York
Tohoku University, Graduate School of Science, Sendai
UMAN, Manchester
Hiroshima University, Graduate School of Science, Higashi-Hiroshima
Cockcroft Institute, Warrington, Cheshire
ATF2 is a final-focus test beam line that attempts to focus the low-emittance beam from the ATF damping ring to a beam size of about 37 nm, and at the same time to demonstrate nm beam stability, using numerous advanced beam diagnostics and feedback tools. The construction is well advanced and beam commissioning of ATF2 has started in the second half of 2008. ATF2 is constructed and commissioned by ATF international collaborations with strong US, Asian and European participation.