Fermilab, Batavia
CERN, Geneva
ETH, Zurich
Funding: Work partly supported by Fermilab, operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy
In the Large Hadron Collider LHC, particles not captured by the RF system at injection or leaking out of the RF bucket may quench the superconducting magnets during beam abort. The problem, common to other superconducting machines, is particularly serious for the LHC due to the very large stored energy in the beam. For the LHC a way of removing the unbunched beam has been studied and it uses the existing damper kickers to excite resonantly the particles travelling along the abort gap. In this paper we describe the results of simulations performed with MAD-X for various LHC optics configurations, including the estimated multipolar errors.
CERN, Geneva
Fermilab, Batavia
Funding: Work partly supported by Fermilab, operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy
Through May to September 2008, further beam commissioning of the SPS to LHC transfer lines was performed. For the first time, optics and dispersion measurements were also taken in the last part of the lines, and into the LHC. Extensive trajectory and optics studies were conducted, in parallel with hardware checks. In particular dispersion measurements and their comparison with the beam line model were analysed in detail and led to propose the addition of a “dispersion-free” steering algorithm in the existing trajectory correction program.
Fermilab, Batavia
Funding: Work supported by Fermilab, operated by Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy
Recent advances in the HTS magnet technology and ionization cooling theory have re-launched the interest of the physics community in the realization of a high energy, high luminosity Muon Collider (MC). The large muon energy spread requires large momentum acceptance and the required luminosity calls for beta* in the mm range. To avoid luminosity degradation due to the hour-glass effect, the bunch length must be comparatively small. To keep the needed RF voltage inside feasible limits the momentum compaction factor must be as small as possible. Under these circumstances chromatic effects correction, energy acceptance, dynamic aperture and longitudinal motion stability are main issues of a MC design. In this paper we give an overview of various lattice designs toward a high luminosity, large energy acceptance MC currently under study at Fermilab.
Fermilab, Batavia
Funding: Fermi Research Alliance, LLC under Contract No. DE-AC02-07CH11359 with the United States Department of Energy.
Muon collider is a promising candidate for the next energy frontier machine. In order to obtain peak luminosity of the order of 1035/cm2/s in the TeV energy range the beta function at the interaction point should be smaller than 1cm. To obtain correspondingly small bunch length with a reasonable RF voltage (within 1GV) the momentum compaction factor should be smaller than 10-4 in the momentum range ~1%. The lattice design must also provide sufficient dynamic aperture for ~20 microns normalized beam emittance and minimum possible circumference. Together these requirements present a challenge which has never been met before. We offer a solution to this problem which has the following distinctive features: i) chromatic compensation achieved with sextupoles and dispersion generating dipoles placed near the IR quadrupoles (not in a special section), ii) low value of momentum compaction factor obtained by balancing positive contribution from the arcs with negative contribution from the suppressors of the generated in the IR dispersion. Theoretical aspects and various options will be discussed.
SLAC, Menlo Park, California
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire
JAI, Oxford
KEK, Ibaraki
IHEP Beijing, Beijing
LAL, Orsay
Royal Holloway, University of London, Surrey
IN2P3-LAPP, Annecy-le-Vieux
OXFORDphysics, Oxford, Oxon
ATOMKI, Debrecen
CERN, Geneva
DESY, Hamburg
Fermilab, Batavia
Kyungpook National University, Daegu
PAL, Pohang, Kyungbuk
Kyoto ICR, Uji, Kyoto
ICEPP, Tokyo
University of Tokyo, Tokyo
UCL, London
BNL, Upton, Long Island, New York
Tohoku University, Graduate School of Science, Sendai
UMAN, Manchester
Hiroshima University, Graduate School of Science, Higashi-Hiroshima
Cockcroft Institute, Warrington, Cheshire
ATF2 is a final-focus test beam line that attempts to focus the low-emittance beam from the ATF damping ring to a beam size of about 37 nm, and at the same time to demonstrate nm beam stability, using numerous advanced beam diagnostics and feedback tools. The construction is well advanced and beam commissioning of ATF2 has started in the second half of 2008. ATF2 is constructed and commissioned by ATF international collaborations with strong US, Asian and European participation.
