CERN, Geneva
LAL, Orsay
INFN/LNF, Frascati (Roma)
Installation of the new photo-injector for the CTF3 drive beam (PHIN) has been completed on a stand-alone test bench. The photo-injector operates with a 2.5 cell RF gun at 3 GHz, using a Cs2Te photocathode illuminated by a UV laser beam. The test bench is equipped with different beam monitoring devices as well as a 90-degree spectrometer. A grid of 200 micrometer wide slits can be inserted for emittance measurements. The laser used to trigger the photo-emission process is a Nd:YLF system consisting of an oscillator and a preamplifier operating at 1.5 GHz and two powerful amplifier stages. The infrared radiation produced is frequency quadrupled in two stages to obtain the UV. A Pockels cell allows adjusting the length of the pulse train between 50 nanoseconds and 50 microseconds. The nominal train length for CTF3 is 1.272 microseconds (1908 bunches). The first electron beam in PHIN was produced in November 2008. In this paper, results concerning the operation of the laser system and measurements performed to characterize the electron beam are presented.
CERN, Geneva
SLAC, Menlo Park, California
Uppsala University, Uppsala
A fundamental element of the CLIC concept is two-beam acceleration, where rf power is extracted from a high-current and low-energy beam in order to accelerate the low-current main beam to high energy. The power extraction occurs in special X-band Power Extraction and Transfer Structures (PETS). The structures are large aperture, high-group velocity and overmoded periodic structures. Following the substantial changes of the CLIC baseline parameters in 2006, the PETS design has been thoroughly updated along with the fabrication methods and corresponding rf components. Two PETS prototypes have been fabricated and high power tested. Test results and future plans are presented.
SLAC, Menlo Park, California
CERN, Geneva
KEK, Ibaraki
Funding: Work supported by the DOE under contract DE-AC02-76SF00515
As part of a SLAC-CERN-KEK collaboration on high gradient X-band structure research, several prototype structures for the CLIC linear collider study have been tested using two of the high power (300 MW) X-band rf stations in the NLCTA facility at SLAC. These structures differ in terms of their manufacturing (brazed disks and clamped quadrants), gradient profile (amount by which the gradient increases along the structure which optimizes efficiency and maximizes sustainable gradient) and HOM damping (use of slots or waveguides to rapidly dissipate dipole mode energy). The CLIC goal in the next few years is to demonstrate the feasibility of a CLIC-ready baseline design and to investigate alternatives which could bring even higher efficiency. This paper summarizes the high gradient test results from the NLCTA in support of this effort.
SLAC, Menlo Park, California
CERN, Geneva
KEK, Ibaraki
Funding: This work was supported by DOE Contract No. DE-AC02-76SF00515 and used resources of NERSC supported by DOE Contract No. DE-AC02-05CH11231, and of NCCS supported by DOE Contract No. DE-AC05-00OR22725.
Normal conducting accelerator structures such as the X-Band NLC structures and the CLIC structures have been found to suffer damage due to RF breakdown and/or dark current when processed to high gradients. Improved understanding of these issues is desirable for the development of structure designs and processing techniques that improve the structure high gradient performance. While vigorous experimental efforts have been put forward to explore the gradient parameter space via high power testing, comprehensive numerical multipacting and dark current simulations would complement measurements by providing an effective probe for observing interior quantities. In this paper, we present studies of multipacting, dark current, and the associated surface heating in high gradient accelerator structures using the parallel finite element simulation code Track3P. Comparisons with the high power test of the CLIC accelerator structures will be presented.
CERN, Geneva
The aim of the last CLIC test facility CTF3, built at CERN by an international collaboration, is to prove the main feasibility issues of the CLIC two-beam acceleration technology. The main points which CTF3 should demonstrate by 2010 are the generation of a very high current drive beam and its use to efficiently produce and transfer RF power to high-gradient accelerating structures. To prove the first point a delay loop and a combiner ring have been built, following a linac, in order to multiply the current by a factor two and four, respectively. The power generation and transfer and the high gradient acceleration are instead demonstrated in the CLIC experimental area (CLEX), where the drive beam is decelerated in special power extraction structures(PETS). In this paper we describe the results of the combination in the ring, properly working after the cure of the vertical instability which limited high current operation, and the commissioning of the new beam lines installed in the second half of 2008, including response matrix analysis and dispersion measurements used to validate the optics model. The results of the energy transfer will be also briefly described.