KEK, Ibaraki
SLAC, Menlo Park, California
Fermilab, Batavia
INFN/LASA, Segrate (MI)
DESY, Hamburg
In an attempt at demonstrating an average field gradient of 31.5 MV/m as per the design accelerating gradient for ILC, a program called S1-Global is in progress as an international research collaboration among KEK, INFN, FNAL, DESY and SLAC. The design of the S1-G cryomodule began at May 2008 by INFN and KEK. The S1-Global cryomodule was designed to contain eight superconducting cavities from FNAL, DESY and KEK, and to be constructed by joining two half-size cryomodules, each 6 m in length. The module containing four cavities from FNAL and DESY was constructed by INFN. Four KEK cavities have been assembled in the 6 m module which KEK fabricated. All major components were transported to KEK from INFN, FNAL and DESY in December 2009. The assembly of the two 6-m cryomodules started from January 2010 in a collaborative work of FNAL, DESY, INFN and KEK. The construction of the S1-G cryomodule will complete in May, and the cool-down of the S1-G cryomodule is scheduled from June 2010 at the KEK-STF. In this paper, the construction and the cold tests of the S1-Global cryomodule in the worldwide research collaboration will be presented.
CERN, Geneva
CEA, Gif-sur-Yvette
INFN/LASA, Segrate (MI)
In the framework of the preparatory phase for the luminosity upgrade of the LHC (SLHC-PP ) it is foreseen to characterize two superconducting RF cavities and demonstrate compliance of the required SPL field stability in amplitude and phase using a prototype LLRF system. We report on the preparation for testing of two super-conducting low-beta cavities at 50 Hz pulse repetition rate including the setting-up of the low level RF control system to evaluate the performance of the piezo-tuning system and cavity field stability in amplitude and phase. Results from tests with 50 Hz pulse repetition rate are presented. Simulations of the RF system are used to predict the necessary specifications for power and bandwidth to control the cavity field and derive specifications for the RF system and its control.
This project has received funding from the European Community's Seventh Framework Programme (FP7/2007-2013) under the Grant Agreement no 212114
IPN, Orsay
IAP, Frankfurt am Main
IN2P3, Paris
INFN/LASA, Segrate (MI)
SCK-CEN, Mol
The goal of the MYRRHA project is to demonstrate the technical feasibility of transmutation in an Accelerator Driven System (ADS) by building a new flexible irradiation complex in Mol (Belgium). The MYRRHA facility requires a 600 MeV accelerator delivering a maximum proton flux of 4 mA CW operation. Such a machine belongs to the category of the high-power proton accelerators, with an additional requirement for exceptional reliability: because of the induced thermal stress to the subcritical core, the number of unwanted beam interruptions should be minimized down to the level of about 10 per 3-month operation cycle, a specification that is far above usual proton accelerators performance. This paper describes the reference solution adopted for such a machine, based on a so-called 'fault-tolerant' linear superconducting accelerator, and presents the status of the associated R&D.
IPN, Orsay
INFN/LASA, Segrate (MI)
Accelerator Driven systems (ADS) are being considered for their potential use in the transmutation of nuclear waste. Because of the induced thermal stress to the subcritical core, the high-power proton LINAC will have to fulfill stringent reliability requirements and to minimize the number of unwanted beam trips per operation cycle. It is forseen to build an ADS demonstrator (MYRRHA) in Mol (Belgium). Such a device will be piloted by a 600 MeV / 4mA superconducting linac. IPN Orsay and INFN Milano are in charge of the realisation and tests of a prototypical cryomodule for the high energy section of the accelerator, equipped with a 5-cell superconducting cavity. Developed at INFN, this RF cryogenic accelerating device is tested for the first time at IPN. We will describe the status of the R&D activities on this device. The first low power tests of the 5-cell superconducting cavity in its prototypical cryomodule will be reviewed. Those tests aim to evaluate the cavity performances after installation in the module (16MV/m in vertical test) but also to measure the tuning systems behaviors in view of reliability considerations for 'fast fault-recovery scenarios'.