• N. Ohuchi, M. Akemoto, S. Fukuda, H. Hayano, N. Higashi, E. Kako, H. Katagiri, Y. Kojima, Y. Kondou, T. Matsumoto, H. Matsushita, S. Michizono, T. Miura, H. Nakai, H. Nakajima, S. Noguchi, M. Satoh, T. Shidara, T. Shishido, T. Takenaka, A. Terashima, N. Toge, K. Tsuchiya, K. Watanabe, S. Yamaguchi, A. Yamamoto, Y. Yamamoto, K. Yokoya, M. Yoshida
  KEK, Ibaraki
• C. Adolphsen, C.D. Nantista
  SLAC, Menlo Park, California
• T.T. Arkan, S. Barbanotti, H. Carter, M.S. Champion, R.D. Kephart, J.S. Kerby, D.V. Mitchell, Y. Orlov, T.J. Peterson, M.C. Ross
  Fermilab, Batavia
• A. Bosotti, C. Pagani, R. Paparella, P. Pierini
  INFN/LASA, Segrate (MI)
• D. Kostin, L. Lilje, A. Matheisen, W.-D. Möller, N.J. Walker, H. Weise
  DESY, Hamburg

In an attempt at demonstrating an average field gradient of 31.5 MV/m as per the design accelerating gradient for ILC, a program called S1-Global is in progress as an international research collaboration among KEK, INFN, FNAL, DESY and SLAC. The design of the S1-G cryomodule began at May 2008 by INFN and KEK. The S1-Global cryomodule was designed to contain eight superconducting cavities from FNAL, DESY and KEK, and to be constructed by joining two half-size cryomodules, each 6 m in length. The module containing four cavities from FNAL and DESY was constructed by INFN. Four KEK cavities have been assembled in the 6 m module which KEK fabricated. All major components were transported to KEK from INFN, FNAL and DESY in December 2009. The assembly of the two 6-m cryomodules started from January 2010 in a collaborative work of FNAL, DESY, INFN and KEK. The construction of the S1-G cryomodule will complete in May, and the cool-down of the S1-G cryomodule is scheduled from June 2010 at the KEK-STF. In this paper, the construction and the cold tests of the S1-Global cryomodule in the worldwide research collaboration will be presented.

Slides

• F.B. Bouly, J.-L. Biarrotte, S. Bousson, C. Commeaux, C. Joly, J. Lesrel
  IPN, Orsay
• A. Bosotti, P.M. Michelato, R. Paparella, P. Pierini, D. Sertore
  INFN/LASA, Segrate (MI)

Accelerator Driven systems (ADS) are being considered for their potential use in the transmutation of nuclear waste. Because of the induced thermal stress to the subcritical core, the high-power proton LINAC will have to fulfill stringent reliability requirements and to minimize the number of unwanted beam trips per operation cycle. It is forseen to build an ADS demonstrator (MYRRHA) in Mol (Belgium). Such a device will be piloted by a 600 MeV / 4mA superconducting linac. IPN Orsay and INFN Milano are in charge of the realisation and tests of a prototypical cryomodule for the high energy section of the accelerator, equipped with a 5-cell superconducting cavity. Developed at INFN, this RF cryogenic accelerating device is tested for the first time at IPN. We will describe the status of the R&D activities on this device. The first low power tests of the 5-cell superconducting cavity in its prototypical cryomodule will be reviewed. Those tests aim to evaluate the cavity performances after installation in the module (16MV/m in vertical test) but also to measure the tuning systems behaviors in view of reliability considerations for 'fast fault-recovery scenarios'.