IPAC2013 - List of Authors (Gabor, C.)

Paper	Title	Page
MOPWA049	Status Report of the FETS Photo Detachment Emittance Instrument at RAL	783
	C. Gabor STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom G.E. Boorman, A. Bosco, S.M. Gibson Royal Holloway, University of London, Surrey, United Kingdom G.E. Boorman, A. Bosco, S.M. Gibson JAI, Egham, Surrey, United Kingdom A.P. Letchford STFC/RAL/ISIS, Chilton, Didcot, Oxon, United Kingdom P. Savage Imperial College of Science and Technology, Department of Physics, London, United Kingdom V.E. Scarpine Fermilab, Batavia, USA
	The Front End Test Stand at the Rutherford Appleton Laboratory (RAL) is being developed to demonstrate a chopped H⁻ beam of 60 mA at 3 MeV with 10% duty cycle. Due to the high beam power it is advisable to use the technique of photo detachment to avoid intrusive methods. It is intended to apply this technique to perform emittance measurements at the output of the RFQ at full power. This requires a dedicated diagnostics dipole with a special-made vacuum chamber giving room for the different beam paths necessary to install a particle detector to measure the produced neutrals. Other aspects are the beam transport and influence of the dipole and its fringe field to the beam transport Other considerations are the installation of the laser, the optics and the particle detector itself.

THPWO086	Status of the RAL Front End Test Stand	3963
	A.P. Letchford, M.A. Clarke-Gayther, D.C. Faircloth, S.R. Lawrie STFC/RAL/ISIS, Chilton, Didcot, Oxon, United Kingdom S.M.H. Alsari, M. Aslaninejad, J.K. Pozimski, P. Savage Imperial College of Science and Technology, Department of Physics, London, United Kingdom J.J. Back University of Warwick, Coventry, United Kingdom G.E. Boorman, A. Bosco, S.M. Gibson Royal Holloway, University of London, Surrey, United Kingdom R.T.P. D'Arcy, S. Jolly UCL, London, United Kingdom C. Gabor, D.C. Plostinar STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom J.K. Pozimski STFC/RAL, Chilton, Didcot, Oxon, United Kingdom
	The Front End Test Stand (FETS) under construction at RAL is a demonstrator for the front end systems of a future high power proton linac. Possible applications include a linac upgrade for the ISIS spallation neutron source, new future neutron sources, accelerator driven sub-critical systems, a neutrino factory etc. Designed to deliver a 60mA H-minus beam at 3MeV with a 10% duty factor, FETS consists of a high brightness ion source, magnetic low energy beam transport (LEBT), 4-vane 324MHz radio frequency quadrupole, medium energy beam transport (MEBT) containing a high speed beam chopper and non-destructive photo-detachment diagnostics. This paper describes the current status of the project and future plans.

Paper

Title

Page

Status Report of the FETS Photo Detachment Emittance Instrument at RAL

783

C. Gabor
STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom
G.E. Boorman, A. Bosco, S.M. Gibson
Royal Holloway, University of London, Surrey, United Kingdom
G.E. Boorman, A. Bosco, S.M. Gibson
JAI, Egham, Surrey, United Kingdom
A.P. Letchford
STFC/RAL/ISIS, Chilton, Didcot, Oxon, United Kingdom
P. Savage
Imperial College of Science and Technology, Department of Physics, London, United Kingdom
V.E. Scarpine
Fermilab, Batavia, USA

The Front End Test Stand at the Rutherford Appleton Laboratory (RAL) is being developed to demonstrate a chopped H⁻ beam of 60 mA at 3 MeV with 10% duty cycle. Due to the high beam power it is advisable to use the technique of photo detachment to avoid intrusive methods. It is intended to apply this technique to perform emittance measurements at the output of the RFQ at full power. This requires a dedicated diagnostics dipole with a special-made vacuum chamber giving room for the different beam paths necessary to install a particle detector to measure the produced neutrals. Other aspects are the beam transport and influence of the dipole and its fringe field to the beam transport Other considerations are the installation of the laser, the optics and the particle detector itself.

THPWO086

Status of the RAL Front End Test Stand

3963

A.P. Letchford, M.A. Clarke-Gayther, D.C. Faircloth, S.R. Lawrie
STFC/RAL/ISIS, Chilton, Didcot, Oxon, United Kingdom
S.M.H. Alsari, M. Aslaninejad, J.K. Pozimski, P. Savage
Imperial College of Science and Technology, Department of Physics, London, United Kingdom
J.J. Back
University of Warwick, Coventry, United Kingdom
G.E. Boorman, A. Bosco, S.M. Gibson
Royal Holloway, University of London, Surrey, United Kingdom
R.T.P. D'Arcy, S. Jolly
UCL, London, United Kingdom
C. Gabor, D.C. Plostinar
STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom
J.K. Pozimski
STFC/RAL, Chilton, Didcot, Oxon, United Kingdom

The Front End Test Stand (FETS) under construction at RAL is a demonstrator for the front end systems of a future high power proton linac. Possible applications include a linac upgrade for the ISIS spallation neutron source, new future neutron sources, accelerator driven sub-critical systems, a neutrino factory etc. Designed to deliver a 60mA H-minus beam at 3MeV with a 10% duty factor, FETS consists of a high brightness ion source, magnetic low energy beam transport (LEBT), 4-vane 324MHz radio frequency quadrupole, medium energy beam transport (MEBT) containing a high speed beam chopper and non-destructive photo-detachment diagnostics. This paper describes the current status of the project and future plans.