IPAC2011 - List of Authors (Drago, A.)

Paper

Title

Page

DAΦNE Bunch-by-bunch Feedback Upgrade as SuperB Design Test

490

A. Drago
INFN/LNF, Frascati (Roma), Italy
D. Teytelman
Dimtel, San Jose, USA

DAΦNE, the PHI-factory located in Frascati, has always shown dynamic behavior strongly dependent on the bunch-by-bunch feedback, since its first runs in 1997. Over the years, to keep up with the evolving machine requirements, transverse and longitudinal systems have received multiple upgrades and updates. During fall 2010, all the six DAΦNE feedback systems have been upgraded to support the next run for KLOE as well as to test bunch-by-bunch feedback architectures intended for the future Italian SuperB factory. Both e+/e^- longitudinal feedback systems have been completely replaced with new hardware for increased reliability, better diagnostics and improved maintainability. In the effort to reduce residual dipole beam motion, determined by the front-end and quantization noise floor, vertical feedback systems now feature a 12-bit ADC, in place of the older 8-bit design. In the paper, we describe the hardware and software changes of this upgrade. Feedback performance analysis and beam dynamics data collected by the systems are presented.

WEPC077

Beam Based Measurements with the Modified Wigglers in DAΦNE

2196

S. Bettoni
CERN, Geneva, Switzerland
A. Drago, S. Guiducci, C. Milardi, M.A. Preger, P. Raimondi
INFN/LNF, Frascati (Roma), Italy

A novel idea to minimize the odd high order non-linearities in periodic magnets has been presented in other articles in the past. The optimization of this method on the wigglers of the main rings in DAΦNE has been performed by means of multipolar and tracking analysis. After the magnetic measurements on a spare wiggler confirmed the magnetic model used to optimize the DAΦNE wigglers, all the insertion devices in the main rings have been modified accordingly. In fall last year tune variation measurements as a function of closed orbit bumps around the wigglers confirmed the validity of the method. In this paper the beam based measurement results with the new configuration are discussed and compared with those obtained in the previous configurations.

THYB01

Advanced Beam Manipulation Techniques at SPARC

2877

A. Mostacci, D. Alesini, P. Antici, A. Bacci, M. Bellaveglia, R. Boni, M. Castellano, E. Chiadroni, G. Di Pirro, A. Drago, M. Ferrario, A. Gallo, G. Gatti, A. Ghigo, E. Pace, A.R. Rossi, B. Spataro, C. Vaccarezza
INFN/LNF, Frascati (Roma), Italy
A. Cianchi
Università di Roma II Tor Vergata, Roma, Italy
B. Marchetti
INFN-Roma II, Roma, Italy
M. Migliorati
University of Rome "La Sapienza", Rome, Italy
L. Palumbo
Rome University La Sapienza, Roma, Italy
V. Petrillo, L. Serafini
Istituto Nazionale di Fisica Nucleare, Milano, Italy
C. Ronsivalle
ENEA C.R. Frascati, Frascati (Roma), Italy

SPARC in Frascati is a high brightness photo-injector used to drive Free Electron Laser experiments and explore advanced beam manipulation techniques. The R&D effort made for the optimization of the beam parameters will be presented here, together with the major experimental results achieved. In particular, we will focus on the generation of sub-picosecond, high brightness electron bunch trains via velocity bunching technique (the so called comb beam). Such bunch trains can be used to drive tunable and narrow band THz sources, FELs and plasma wake field accelerators.

Slides THYB01 [20.772 MB]

THPZ003

The SuperB Project: Accelerator Status and R&D

3684

M.E. Biagini, S. Bini, R. Boni, M. Boscolo, B. Buonomo, T. Demma, E. Di Pasquale, A. Drago, L.G. Foggetta, S. Guiducci, S.M. Liuzzo, G. Mazzitelli, L. Pellegrino, M.A. Preger, P. Raimondi, U. Rotundo, C. Sanelli, M. Serio, A. Stecchi, A. Stella, S. Tomassini, M. Zobov
INFN/LNF, Frascati (Roma), Italy
M.A. Baylac, O. Bourrion, J.-M. De Conto, N. Monseu, C. Vescovi
LPSC, Grenoble, France
K.J. Bertsche, A. Brachmann, Y. Cai, A. Chao, M.H. Donald, R.C. Field, A.S. Fisher, D. Kharakh, A. Krasnykh, K.C. Moffeit, Y. Nosochkov, A. Novokhatski, M.T.F. Pivi, J.T. Seeman, M.K. Sullivan, S.P. Weathersby, A.W. Weidemann, U. Wienands, W. Wittmer, G. Yocky
SLAC, Menlo Park, California, USA
S. Bettoni
PSI, Villigen, Switzerland
A.V. Bogomyagkov, I. Koop, E.B. Levichev, S.A. Nikitin, I.N. Okunev, P.A. Piminov, D.N. Shatilov, S.V. Sinyatkin, P. Vobly
BINP SB RAS, Novosibirsk, Russia
B. Bolzon, M. Esposito
CERN, Geneva, Switzerland
F. Bosi
INFN-Pisa, Pisa, Italy
L. Brunetti, A. Jeremie
IN2P3-LAPP, Annecy-le-Vieux, France
A. Chancé
CEA, Gif-sur-Yvette, France
P. Fabbricatore, S. Farinon, R. Musenich
INFN Genova, Genova, Italy
E. Paoloni
University of Pisa and INFN, Pisa, Italy
C. Rimbault, A. Variola
LAL, Orsay, France
Y. Zhang
IHEP Beijing, Beijing, People's Republic of China

The SuperB collider project has been recently approved by the Italian Government as part of the National Research Plan. SuperB is a high luminosity (10³6 cm^-2 s^-1) asymmetric e⁺e⁻ collider at the Y(4S) energy. The design is based on a “large Piwinski angle and Crab Waist” scheme already successfully tested at the DAΦNE Phi-Factory in Frascati, Italy. The project combines the challenges of high luminosity colliders and state-of-the-art synchrotron light sources, with two beams (e⁺ at 6.7 and e^- at 4.2 GeV) with extremely low emittances and small beam sizes at the Interaction Point. As unique features, the electron beam will be longitudinally polarized at the IP and the rings will be able to ramp down to collide at the tau/charm energy threshold with one tenth the luminosity. The relatively low beam currents (about 2 A) will allow for low running (power) costs compared to similar machines. The insertion of beam lines for synchrotron radiation users is the latest feature included in the design. The lattice has been recently modified to accommodate insertion devices for X-rays production. A status of the project and a description of R&D in progress will be presented.

THPZ004

DAΦNE Tune-up for the KLOE-2 Experiment

3687

C. Milardi, D. Alesini, M.E. Biagini, S. Bini, C. Biscari, R. Boni, M. Boscolo, B. Buonomo, A. Clozza, G.O. Delle Monache, T. Demma, E. Di Pasquale, G. Di Pirro, A. Drago, M. Esposito, L.G. Foggetta, A. Gallo, A. Ghigo, S. Guiducci, C. Ligi, S.M. Liuzzo, F. Marcellini, G. Mazzitelli, L. Pellegrino, M.A. Preger, L. Quintieri, P. Raimondi, R. Ricci, U. Rotundo, C. Sanelli, M. Serio, F. Sgamma, B. Spataro, A. Stecchi, A. Stella, S. Tomassini, C. Vaccarezza, M. Zobov
INFN/LNF, Frascati (Roma), Italy
S. Bettoni
PSI, Villigen, Switzerland

Funding: Work supported by the EuCARD research programme within the 'Assessment of Novel Accelerator Concepts' work package (ANAC-WP11).
In its continuous evolution DAΦNE, the Frascati lepton collider, is starting a new run for the KLOE-2 experiment, an upgraded version of the KLOE one. A new interaction region, based on the high luminosity Crab-Waist collision scheme, has been designed, built and installed. Several machine subsystems have been revised according to innovative design concepts in order to improve beam dynamics. Collimators and shieldings have been upgraded in order to minimize the background rates on the detector during coasting as well as injection operation. A wide measurement campaign has been undertaken to verify and quantify the effect of the modifications and to tune-up the collider in view of the 3 years long data-taking foreseen to deliver ~5 fb-1 to the experiment.

Paper	Title	Page
MOPO006	DAΦNE Bunch-by-bunch Feedback Upgrade as SuperB Design Test	490
	A. Drago INFN/LNF, Frascati (Roma), Italy D. Teytelman Dimtel, San Jose, USA
	DAΦNE, the PHI-factory located in Frascati, has always shown dynamic behavior strongly dependent on the bunch-by-bunch feedback, since its first runs in 1997. Over the years, to keep up with the evolving machine requirements, transverse and longitudinal systems have received multiple upgrades and updates. During fall 2010, all the six DAΦNE feedback systems have been upgraded to support the next run for KLOE as well as to test bunch-by-bunch feedback architectures intended for the future Italian SuperB factory. Both e+/e^- longitudinal feedback systems have been completely replaced with new hardware for increased reliability, better diagnostics and improved maintainability. In the effort to reduce residual dipole beam motion, determined by the front-end and quantization noise floor, vertical feedback systems now feature a 12-bit ADC, in place of the older 8-bit design. In the paper, we describe the hardware and software changes of this upgrade. Feedback performance analysis and beam dynamics data collected by the systems are presented.

WEPC077	Beam Based Measurements with the Modified Wigglers in DAΦNE	2196
	S. Bettoni CERN, Geneva, Switzerland A. Drago, S. Guiducci, C. Milardi, M.A. Preger, P. Raimondi INFN/LNF, Frascati (Roma), Italy
	A novel idea to minimize the odd high order non-linearities in periodic magnets has been presented in other articles in the past. The optimization of this method on the wigglers of the main rings in DAΦNE has been performed by means of multipolar and tracking analysis. After the magnetic measurements on a spare wiggler confirmed the magnetic model used to optimize the DAΦNE wigglers, all the insertion devices in the main rings have been modified accordingly. In fall last year tune variation measurements as a function of closed orbit bumps around the wigglers confirmed the validity of the method. In this paper the beam based measurement results with the new configuration are discussed and compared with those obtained in the previous configurations.

THYB01	Advanced Beam Manipulation Techniques at SPARC	2877
	A. Mostacci, D. Alesini, P. Antici, A. Bacci, M. Bellaveglia, R. Boni, M. Castellano, E. Chiadroni, G. Di Pirro, A. Drago, M. Ferrario, A. Gallo, G. Gatti, A. Ghigo, E. Pace, A.R. Rossi, B. Spataro, C. Vaccarezza INFN/LNF, Frascati (Roma), Italy A. Cianchi Università di Roma II Tor Vergata, Roma, Italy B. Marchetti INFN-Roma II, Roma, Italy M. Migliorati University of Rome "La Sapienza", Rome, Italy L. Palumbo Rome University La Sapienza, Roma, Italy V. Petrillo, L. Serafini Istituto Nazionale di Fisica Nucleare, Milano, Italy C. Ronsivalle ENEA C.R. Frascati, Frascati (Roma), Italy
	SPARC in Frascati is a high brightness photo-injector used to drive Free Electron Laser experiments and explore advanced beam manipulation techniques. The R&D effort made for the optimization of the beam parameters will be presented here, together with the major experimental results achieved. In particular, we will focus on the generation of sub-picosecond, high brightness electron bunch trains via velocity bunching technique (the so called comb beam). Such bunch trains can be used to drive tunable and narrow band THz sources, FELs and plasma wake field accelerators.
	Slides THYB01 [20.772 MB]

THPZ003	The SuperB Project: Accelerator Status and R&D	3684
	M.E. Biagini, S. Bini, R. Boni, M. Boscolo, B. Buonomo, T. Demma, E. Di Pasquale, A. Drago, L.G. Foggetta, S. Guiducci, S.M. Liuzzo, G. Mazzitelli, L. Pellegrino, M.A. Preger, P. Raimondi, U. Rotundo, C. Sanelli, M. Serio, A. Stecchi, A. Stella, S. Tomassini, M. Zobov INFN/LNF, Frascati (Roma), Italy M.A. Baylac, O. Bourrion, J.-M. De Conto, N. Monseu, C. Vescovi LPSC, Grenoble, France K.J. Bertsche, A. Brachmann, Y. Cai, A. Chao, M.H. Donald, R.C. Field, A.S. Fisher, D. Kharakh, A. Krasnykh, K.C. Moffeit, Y. Nosochkov, A. Novokhatski, M.T.F. Pivi, J.T. Seeman, M.K. Sullivan, S.P. Weathersby, A.W. Weidemann, U. Wienands, W. Wittmer, G. Yocky SLAC, Menlo Park, California, USA S. Bettoni PSI, Villigen, Switzerland A.V. Bogomyagkov, I. Koop, E.B. Levichev, S.A. Nikitin, I.N. Okunev, P.A. Piminov, D.N. Shatilov, S.V. Sinyatkin, P. Vobly BINP SB RAS, Novosibirsk, Russia B. Bolzon, M. Esposito CERN, Geneva, Switzerland F. Bosi INFN-Pisa, Pisa, Italy L. Brunetti, A. Jeremie IN2P3-LAPP, Annecy-le-Vieux, France A. Chancé CEA, Gif-sur-Yvette, France P. Fabbricatore, S. Farinon, R. Musenich INFN Genova, Genova, Italy E. Paoloni University of Pisa and INFN, Pisa, Italy C. Rimbault, A. Variola LAL, Orsay, France Y. Zhang IHEP Beijing, Beijing, People's Republic of China
	The SuperB collider project has been recently approved by the Italian Government as part of the National Research Plan. SuperB is a high luminosity (10³6 cm^-2 s^-1) asymmetric e⁺e⁻ collider at the Y(4S) energy. The design is based on a “large Piwinski angle and Crab Waist” scheme already successfully tested at the DAΦNE Phi-Factory in Frascati, Italy. The project combines the challenges of high luminosity colliders and state-of-the-art synchrotron light sources, with two beams (e⁺ at 6.7 and e^- at 4.2 GeV) with extremely low emittances and small beam sizes at the Interaction Point. As unique features, the electron beam will be longitudinally polarized at the IP and the rings will be able to ramp down to collide at the tau/charm energy threshold with one tenth the luminosity. The relatively low beam currents (about 2 A) will allow for low running (power) costs compared to similar machines. The insertion of beam lines for synchrotron radiation users is the latest feature included in the design. The lattice has been recently modified to accommodate insertion devices for X-rays production. A status of the project and a description of R&D in progress will be presented.

THPZ004	DAΦNE Tune-up for the KLOE-2 Experiment	3687
	C. Milardi, D. Alesini, M.E. Biagini, S. Bini, C. Biscari, R. Boni, M. Boscolo, B. Buonomo, A. Clozza, G.O. Delle Monache, T. Demma, E. Di Pasquale, G. Di Pirro, A. Drago, M. Esposito, L.G. Foggetta, A. Gallo, A. Ghigo, S. Guiducci, C. Ligi, S.M. Liuzzo, F. Marcellini, G. Mazzitelli, L. Pellegrino, M.A. Preger, L. Quintieri, P. Raimondi, R. Ricci, U. Rotundo, C. Sanelli, M. Serio, F. Sgamma, B. Spataro, A. Stecchi, A. Stella, S. Tomassini, C. Vaccarezza, M. Zobov INFN/LNF, Frascati (Roma), Italy S. Bettoni PSI, Villigen, Switzerland
	Funding: Work supported by the EuCARD research programme within the 'Assessment of Novel Accelerator Concepts' work package (ANAC-WP11). In its continuous evolution DAΦNE, the Frascati lepton collider, is starting a new run for the KLOE-2 experiment, an upgraded version of the KLOE one. A new interaction region, based on the high luminosity Crab-Waist collision scheme, has been designed, built and installed. Several machine subsystems have been revised according to innovative design concepts in order to improve beam dynamics. Collimators and shieldings have been upgraded in order to minimize the background rates on the detector during coasting as well as injection operation. A wide measurement campaign has been undertaken to verify and quantify the effect of the modifications and to tune-up the collider in view of the 3 years long data-taking foreseen to deliver ~5 fb-1 to the experiment.