IPAC2011 - List of Authors (Anders, W.)

Paper

Title

Page

First Characterization of a Fully Superconducting RF Photoinjector Cavity

41

A. Neumann, W. Anders, R. Barday, A. Jankowiak, T. Kamps, J. Knobloch, O. Kugeler, A.N. Matveenko, T. Quast, J. Rudolph, S.G. Schubert, J. Völker
HZB, Berlin, Germany
P. Kneisel
JLAB, Newport News, Virginia, USA
R. Nietubyc
The Andrzej Soltan Institute for Nuclear Studies, Centre Swierk, Swierk/Otwock, Poland
J.K. Sekutowicz
DESY, Hamburg, Germany
J. Smedley
BNL, Upton, Long Island, New York, USA
V. Volkov
BINP SB RAS, Novosibirsk, Russia
G. Weinberg
FHI, Berlin, Germany
I. Will
MBI, Berlin, Germany

As a first step towards a high brightness, high average current electron source for the BERLinPro ERL a fully superconducting photo-injector was developed by HZB in collaboration with JLab, DESY and the A. Soltan Institute. This cavity-injector ensemble is made up of a 1.6-cell superconducting cavity with a superconducting lead cathode deposited on the half-cell backwall. A superconducting solenoid is used for emittance compensation. This system, including a diagnostics beamline, has been installed in the HoBiCaT facility to serve as a testbed for beam dynamics studies and to test the combination SRF cavity and superconducting solenoid. This paper summarizes the characterization of the cavity in this configuration including Q measurements, dark current tests and field-stability analyses.

Slides MOODA03 [10.343 MB]

MOPC080

First Considerations Concerning an Optimized Cavity Design for the Main Linac of BERLinPro

259

B. Riemann, T. Weis
DELTA, Dortmund, Germany
W. Anders, J. Knobloch, A. Neumann
HZB, Berlin, Germany
H.-W. Glock, C. Potratz, U. van Rienen
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany
F. Marhauser
JLAB, Newport News, Virginia, USA

Funding: work supported by BMBF under contracts 05K10PEA and 05K10HRC
The Berlin Energy Recovery Linac Project (BERLinPro) is designed to develop and demonstrate CW linac technology and expertise required to drive next-generation Energy Recovery Linacs. Strongly HOM-damped multicell 1.3 GHz cavities are required for the main linac. The optimization of the cavities presented here is primarily based on the CEBAF 1.5 GHz 5-cell high-current cavity design, including HOM waveguide couplers. The cavity was scaled to 1.3 GHz and extended to 7 cells. Modifications to the end group design have also been studied. An effort was also made to reduce the ratio Epk/Eacc while still permitting HOMs to propagate.

THPC109

First Demonstration of Electron Beam Generation and Characterization with an All Superconducting Radio-frequency (SRF) Photoinjector*

3143

T. Kamps, W. Anders, R. Barday, A. Jankowiak, J. Knobloch, O. Kugeler, A.N. Matveenko, A. Neumann, T. Quast, J. Rudolph, S.G. Schubert, J. Völker
HZB, Berlin, Germany
P. Kneisel
JLAB, Newport News, Virginia, USA
R. Nietubyc
The Andrzej Soltan Institute for Nuclear Studies, Centre Swierk, Swierk/Otwock, Poland
J.K. Sekutowicz
DESY, Hamburg, Germany
J. Smedley
BNL, Upton, Long Island, New York, USA
V. Volkov
BINP SB RAS, Novosibirsk, Russia
G. Weinberg
FHI, Berlin, Germany
I. Will
MBI, Berlin, Germany

Funding: Work supported by Bundesministerium für Bildung und Forschung und Land Berlin. The work on the Pb cathode film is supported by EuCARD Grant Agreement No. 227579
In preparation for a high brightness, high average current electron source for the energy-recovery linac BERLinPro an all superconducting radio-frequency photoinjector is now in operation at Helmholtz-Zentrum Berlin. The aim of this experiment is beam demonstration with a high brightness electron source able to generate sub-ps pulse length electron bunches from a superconducting (SC) cathode film made of Pb coated on the backwall of a Nb SRF cavity. This paper describes the setup of the experiment and first results from beam measurements.

Paper	Title	Page
MOODA03	First Characterization of a Fully Superconducting RF Photoinjector Cavity	41
	A. Neumann, W. Anders, R. Barday, A. Jankowiak, T. Kamps, J. Knobloch, O. Kugeler, A.N. Matveenko, T. Quast, J. Rudolph, S.G. Schubert, J. Völker HZB, Berlin, Germany P. Kneisel JLAB, Newport News, Virginia, USA R. Nietubyc The Andrzej Soltan Institute for Nuclear Studies, Centre Swierk, Swierk/Otwock, Poland J.K. Sekutowicz DESY, Hamburg, Germany J. Smedley BNL, Upton, Long Island, New York, USA V. Volkov BINP SB RAS, Novosibirsk, Russia G. Weinberg FHI, Berlin, Germany I. Will MBI, Berlin, Germany
	As a first step towards a high brightness, high average current electron source for the BERLinPro ERL a fully superconducting photo-injector was developed by HZB in collaboration with JLab, DESY and the A. Soltan Institute. This cavity-injector ensemble is made up of a 1.6-cell superconducting cavity with a superconducting lead cathode deposited on the half-cell backwall. A superconducting solenoid is used for emittance compensation. This system, including a diagnostics beamline, has been installed in the HoBiCaT facility to serve as a testbed for beam dynamics studies and to test the combination SRF cavity and superconducting solenoid. This paper summarizes the characterization of the cavity in this configuration including Q measurements, dark current tests and field-stability analyses.
	Slides MOODA03 [10.343 MB]

MOPC080	First Considerations Concerning an Optimized Cavity Design for the Main Linac of BERLinPro	259
	B. Riemann, T. Weis DELTA, Dortmund, Germany W. Anders, J. Knobloch, A. Neumann HZB, Berlin, Germany H.-W. Glock, C. Potratz, U. van Rienen Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany F. Marhauser JLAB, Newport News, Virginia, USA
	Funding: work supported by BMBF under contracts 05K10PEA and 05K10HRC The Berlin Energy Recovery Linac Project (BERLinPro) is designed to develop and demonstrate CW linac technology and expertise required to drive next-generation Energy Recovery Linacs. Strongly HOM-damped multicell 1.3 GHz cavities are required for the main linac. The optimization of the cavities presented here is primarily based on the CEBAF 1.5 GHz 5-cell high-current cavity design, including HOM waveguide couplers. The cavity was scaled to 1.3 GHz and extended to 7 cells. Modifications to the end group design have also been studied. An effort was also made to reduce the ratio Epk/Eacc while still permitting HOMs to propagate.

THPC109	First Demonstration of Electron Beam Generation and Characterization with an All Superconducting Radio-frequency (SRF) Photoinjector*	3143
	T. Kamps, W. Anders, R. Barday, A. Jankowiak, J. Knobloch, O. Kugeler, A.N. Matveenko, A. Neumann, T. Quast, J. Rudolph, S.G. Schubert, J. Völker HZB, Berlin, Germany P. Kneisel JLAB, Newport News, Virginia, USA R. Nietubyc The Andrzej Soltan Institute for Nuclear Studies, Centre Swierk, Swierk/Otwock, Poland J.K. Sekutowicz DESY, Hamburg, Germany J. Smedley BNL, Upton, Long Island, New York, USA V. Volkov BINP SB RAS, Novosibirsk, Russia G. Weinberg FHI, Berlin, Germany I. Will MBI, Berlin, Germany
	Funding: Work supported by Bundesministerium für Bildung und Forschung und Land Berlin. The work on the Pb cathode film is supported by EuCARD Grant Agreement No. 227579 In preparation for a high brightness, high average current electron source for the energy-recovery linac BERLinPro an all superconducting radio-frequency photoinjector is now in operation at Helmholtz-Zentrum Berlin. The aim of this experiment is beam demonstration with a high brightness electron source able to generate sub-ps pulse length electron bunches from a superconducting (SC) cathode film made of Pb coated on the backwall of a Nb SRF cavity. This paper describes the setup of the experiment and first results from beam measurements.