| Paper | Title | Page |
|---|---|---|
| MOPD021 | Low Energy Ion Injector at KACST | 720 |
|
||
|
At the National Centre for Mathematics and Physics (NCMP), at the King Abdulaziz City for Science and Technology (KACST), Saudi Arabia, a versatile low energy ion injector has been developed in collaboration with the QUASAR group. This project will allow for a broad experimental program with most different kinds of ions both in single pass setups, but also with ions stored in a fixed-energy electrostatic storage ring. In this contribution, the design of the injector is presented. It was designed for beams with energies of up to 30 kV/q and will allow for switching between different ion sources from e.g. duoplasmatron to electrospray ion sources and to thus provide the users with a wide range of different beams. The mechanical construction of the injector is summarized and the status of its assembly at KACST presented. |
||
| MOPD022 | Design of a Combined Fast and Slow Extraction for the Ultra-low Energy Storage Ring (USR) | 723 |
|
||
|
The Ultra-Low energy Storage Ring (USR) within the future Facility for Low-energy Antiproton and Ion Research (FLAIR) will decelerate antiproton beams from 300 keV to energies of only 20 keV. Cooled beams will then be extracted and provided to external experiments. The large variety of planned experiments requires a highly flexible longitudinal time structure of the extracted bunches, ranging from ultra-short pulses in the nanosecond regime to quasi DC beams. This requires fast as well as slow extraction in order to cover whole range of envisaged beam parameters. A particular challenge was to combine elements for fast and slow extraction in one straight section of this electrostatic ring. In this contribution we present the results of beam dynamic simulations and describe the overall extraction scheme in detail. |
||
| MOPD023 | DITANET - Investigations into Accelerator Beam Diagnostics | 726 |
|
||
|
The Marie Curie Initial Training Network DITANET covers the development of advanced beam diagnostic methods for a wide range of existing or future accelerators, both for electrons and ions. The network brings together research centres like CERN or DESY, Universities, and private companies. DITANET currently has 27 partners from Europe and the USA and is committed to training young researchers in this field, performing cutting edge research in beam instrumentation, and exploiting synergies within this community. This contribution presents an overview of the research outcomes within the first two years of DITANET and summarizes the network's training activities. on behalf of the DITANET Consortium. |
||
| MOPD024 | Scintillating Screen Studies for Low Energy, Low Intensity Beams | 729 |
|
||
|
Future atomic and nuclear physics experiments put challenging demands on the required beam instrumentation. Low energy (<1 MeV), low intensity (<107 pps) beams will require highly sensitive monitors. This is especially true for the Facility for Low-energy Antiproton and Ion Research (FLAIR) where antiproton beams will be decelerated down to 20 keV and as few as 5·105 particles per second will be slowly extracted for external experiments. In order to investigate the limits of scintillating screens for beam profile monitoring in the low energy, low intensity regime a structured analysis of several screen materials, including CsI:Tl, YAG:Ce and scintillating fibre optic plate (SFOP), has been done under different irradiation conditions with keV proton beams. This contribution will present the experimental setup and summarize the results of this study. |
||
| MOPE073 | Optimization Studies of Planar Supersonic Gas-jets for Beam Profile Monitor Applications | 1149 |
|
||
|
Supersonic gas-jets have attracted much interest as experimental targets in several fields of science since they combine low internal temperatures with high directionality. Axisymmetric jets have found widespread application, triggering a wealth of studies on their properties, while only a limited number of detailed studies have been done on planar jets. In this paper, the design of a beam profile monitor based on a planar supersonic gas-jet for use in the Ultra-low energy Storage Ring (USR) at the Facility for Antiproton and Ion Research (FAIR) in Germany is described. Optimization of the monitor requires investigation into different characteristic jet parameters. For that purpose extensive simulation work with the Gas Dynamics Tool (GDT) was done. The results of these studies are presented together with a description of a novel nozzle-skimmer configuration and an experimental test stand to benchmark the numerical results. |
||
| TUPD014 | Simulations of Space Charge Effects in Low Energy Electrostatic Storage Rings | 1952 |
|
||
|
Electrostatic storage rings have proven to be invaluable tools for atomic and molecular physics. Due to the mass independence of the electrostatic rigidity, these machines are able to store a wide range of different particles, from light ions to heavy singly charged bio-molecules. However, earlier measurements showed strong space charge limitations; probably linked to non-linear fields that cannot be completely avoided in such machines. The nature of these effects is not fully understood. In this contribution, we present the results from simulating an electrostatic storage ring under consideration of non-linear fields as well as space charge effects using the computer code SCALA. |
||
| WEPEB074 | Requirements of CLIC Beam Loss Monitoring System | 2869 |
|
||
|
The Compact Linear Collider (CLIC) is a proposed multi-TeV linear electron-positron collider being designed by a world-wide collaboration. It is based on a novel two-beam acceleration scheme in which two beams (drive and main beam) are placed in parallel to each other and energy is transferred from the drive beam to the main one. Beam losses on either of them can have catastrophic consequences for the machine because of high intensity (drive beam) or high energy and small emittance (main beam). In the framework of machine protection, a Beam Loss Monitoring system has to be put in place. This paper discusses the requirements for the beam loss system in terms of detector sensitivity, resolution, dynamic range and ability to distinguish losses originating from various sources. A particular attention is given to the two-beam module where the protection from beam losses is particularly challenging and important. |
||
| WEPEB075 | Beam Halo Studies for CTF3 | 2872 |
|
||
|
Beam halo can have severe effects on the performance of high energy accelerators. It reduces the experimental throughput, may lead to noise in the experiments, or even damaging of accelerator components. In order to understand and ideally control the formation and evolution of beam halo, detailed simulation studies are required. In this contribution halo generation mechanisms and the underlying physical principles are first presented, before the particular case of the CLIC Test Facility (CTF3) is discussed in detail. Analytical, numerical and simulation studies are combined to estimate the relevant sources of halo formation and to study halo propagation in the different CTF3 sections. |
||
| THPE082 | Higher Order Mode Analysis of the SPL Cavities | 4713 |
|
||
|
Higher Order Modes (HOMs) can severely limit the operation of superconducting cavities in a linac with high beam current, high duty factor and complex pulse structure. The full HOM spectrum has to be analyzed in order to identify potentially dangerous modes already during the design phase and to define their damping requirements. For this purpose a dedicated beam simulation code focused on beam-HOM interaction was developed, taking into account important effects like the HOM frequency spread, beam input jitter, different chopping patterns, as well as klystron and alignment errors. Here this code is used to investigate in detail the HOM properties of the cavities foreseen in the Superconducting Proton Linac (SPL) at CERN and their potential to drive beam instabilities. A special focus is set to HOM excitation by chopped pulses with high repetition rate and on the influence of HOMs on recirculating electron beams in the high-energy part of the SPL. Finally, the HOM characteristics of similar linac designs are presented and compared to the SPL. |
||
| MOPD023 | DITANET - Investigations into Accelerator Beam Diagnostics | 726 |
|
||
|
The Marie Curie Initial Training Network DITANET covers the development of advanced beam diagnostic methods for a wide range of existing or future accelerators, both for electrons and ions. The network brings together research centres like CERN or DESY, Universities, and private companies. DITANET currently has 27 partners from Europe and the USA and is committed to training young researchers in this field, performing cutting edge research in beam instrumentation, and exploiting synergies within this community. This contribution presents an overview of the research outcomes within the first two years of DITANET and summarizes the network's training activities. on behalf of the DITANET Consortium. |
||
| MOPE055 | Design for a Longitudinal Density Monitor for the LHC | 1098 |
|
||
|
Synchrotron radiation is currently used on LHC for beam imaging and for monitoring the proton population in the 3 microsecond abort gap. In addition to these existing detectors, a study has been initiated to provide longitudinal density profiles of the LHC beams with a high dynamic range and a 50ps time resolution. This would allow for the precise measurement both of the bunch shape and the number of particles in the bunch tail or drifting into ghost bunches. A solution is proposed based on counting synchrotron light photons with two fast avalanche photo‐diodes (APD) operated in Geiger mode. One is free‐running but heavily attenuated and can be used to measure the core of the bunch. The other is much more sensitive, for the measurement of the bunch tails, but must be gated off during the passage of the core of the bunch to prevent the detector from saturating. An algorithm is then applied to combine the two measurements and correct for the detector dead time, after pulsing and pile‐up effects. Initial results from laboratory testing of this system are described in this paper. |
||
| MOPE058 | Measuring the Bunch Frequency Multiplication at CTF3 | 1107 |
|
||
|
The CTF3 facility is being built and commissioned by an international collaboration in order to test the feasibility of the proposed CLIC drive beam generation scheme. Central to this scheme is the use of RF deflectors to inject bunches into a Delay Loop and a Combiner Ring, in order to transform the initial bunch spacing of 1.5 GHz from the linac to a final bunch spacing of 12 GHz. The optimization procedure relies on several steps. The active length of each ring is carefully adjusted to within a few millimeters accuracy using a two‐period undulator. The transverse optics of the machine must be set-up in a way so as to ensure the beam isochronicity. Diagnostics based on optical streak cameras and RF power measurements have been designed to measure the longitudinal behaviour of the beam during the combination. This paper presents their performance and highlights recent measurements. |