• C. Benabderrahmane, P. Berteaud, N. Béchu, M.-E. Couprie, J.-M. Filhol, C. Herbeaux, C.A. Kitegi, J.L. Marlats, K. Tavakoli, M. Valléau, D. Zerbib
  SOLEIL, Gif-sur-Yvette

The production of hard X rays at SOLEIL, a 2.75 GeV, requires short period and small gap in-vacuum undulators. For shifting further the radiation toward higher energies, the peak magnetic field of the undulators can be further increased by cooling the permanent magnets at cryogenic temperature below 100 K. A R&D programme for the construction of a 2 m long 18 mm period CPMU is launched: the use of PrFeB enables to increase the peak magnetic field at a cryogenic temperature of 77 K. Praseodymium was chosen instead of Neodymium type magnets, because it prevents the appearance of the Spin Reorientation Transition. The magnetic characterisation of different permanent magnet grades at cryogenic temperatures (NdFeB and PrFeB), and the magnetic and thermal measurements on a small 4 period NdFeB cryogenic undulator are presented. The status on the progress of the CPMU conception is given. The magnetic and mechanical design, including the cooling of the girders at 77K, and the thermal budget are described. The designs of the dedicated magnetic measurement benches, which will be required to check the magnetic performance of the undulator at low temperature, are also reported.

• C.A. Kitegi, F. Briquez, M.-E. Couprie, T.K. El Ajjouri, J.-M. Filhol, K. Tavakoli, J. Vétéran
  SOLEIL, Gif-sur-Yvette

At SOLEIL, the production of high brilliant photon beams with adjustable polarization is achieved by means of Advanced Planar Polarized Light Emitter-II (APPLE-II) undulators. The HU36 is a short period high field APPLE-II type undulator with 36 mm period and 0.8 T peak field at a minimum gap of 11 mm. The HU36 circularly polarized radiation ranges from 2 keV to 5 keV, while the planar one extends up to 10 keV. High harmonic radiation (up to the 13th) is required to reach such high energy; therefore a small RMS phase error is needed. To enable closing the gap at 11 mm, the HU36 is planned to be installed in a short section where the large horizontal beta function imposes constraining tolerances on the integrated field errors. However at low period and high field, the magnet holders, commonly used at SOLEIL to maintain magnets on the girders, experience mechanical deformation due to the large magnetic forces. This results in the variation of field integrals when the shift between girders is changed. Solutions to minimize these errors are discussed and finally the HU36 magnetic performances are reviewed.

• O. Marcouillé, P. Berteaud, P. Brunelle, N. Béchu, L. Chapuis, M.-E. Couprie, J.-M. Filhol, C. Herbeaux, A. Lestrade, J.L. Marlats, A. Mary, M. Massal, M.-H. Nguyen, K. Tavakoli, M. Valléau, J. Vétéran
  SOLEIL, Gif-sur-Yvette

The production of high fluxes in the hard X-rays region is a major issue on medium energy storage rings. It requires the installation of Insertion Devices with high magnetic field and a large number of periods. The construction of a superconducting wiggler has been first envisaged but reveals to be maintenance constraining, much more complex and expensive than the permanent magnet technology. A small gap in vacuum wiggler composed of 38 periods of 50 mm has been preferred. The compact magnetic system allows to produce in a limited space a magnetic field of 2.1 T in a small gap of 5.5 mm, whereas an auxiliary counterforce system based on non-magnetic springs compensate the magnetic forces (up to 8.5 Tons) acting between magnet arrays. The gap between jaws and the mechanical deformations have been controlled and corrected. Magic fingers corrections have been also performed to reduce the integrated multipoles and to minimize the 2nd order integrals resulting from the tight width of the wiggler poles. This paper presents the design of the wiggler, the construction, and the results of the measurements after magnetic corrections.