Sokendai, Ibaraki
KEK, Ibaraki
Electron Cloud (ECLOUD) deteriorates the performance of proton and positron storage rings. Therefore it is desirable to understand the ECLOUD buildup in a given machine. The data taken by Retarded Field Analyzer (RFA) with a multi channel plate showed that the signal had the peaks coinciding with the positron bunch pattern if a high voltage of -2kV is applied to the retarded grid*. This suggests that the cloud electrons get maximum kick near the positron bunch. A computer program has been developed to study the near bunch ECLOUD density at KEKB LER (Low Energy Ring). In simulations, secondary electron emission is modeled according to the Furman and Pivi's model**. In this paper we compare the simulation results of the ECLOUD buildup with the experiments performed in KEK under different beam-optics elements.
* K. Kanazawa et al., PAC05, 1054.
** M. Furman and M. Pivi, PRST-AB, 5, 124404 (2002).
KEK, Ibaraki
SLAC, Menlo Park, California
Grooved surfaces are effective to suppress the secondary electron emission, and can be a possible technique to mitigate the electron cloud instability (ECI) in positron/proton storage rings. Various types of triangular grooved surfaces have been studied in a laboratory, and also using an intense positron beam of the KEKB B-factory. The grooves have vertex angles of 20 ~ 30 degrees, and depths of 2.5 mm. In the laboratory, the secondary electron yield (SEY) of sample pieces were measured using an electron beam in a magnetic-free condition. The maximum SEY well below 1.0 was obtained after some extent of electron bombardment for most of grooved surfaces. To test he groove efficacy in magnetic field regions of particle accelerators, insertions with several types of grooved surfaces were installed into a test chamber in a wiggler magnet of KEKB positron ring. In a dipole-like chamber wit magnetic field (0.78 T), the reduction in the electron density around the beam was observed for a grooved section when compared to the case of a flat surface with TiN coating. An R&D effort is underway to optimize and manufacture the grooved surface in accelerator beam pipes for practical use.
KEK, Ibaraki
SLAC, Menlo Park, California
In order to mitigate the electron cloud instability (ECI) in a positron ring, an electron clearing electrode with a very thin structure has been developed. The electrode has been tested with an intense positron beam of the KEKB B-factory using a test chamber. A drastic reduction in the electron density around the beam was demonstrated in a dipole magnetic field (0.78 T). The clearing electrode was then applied to the actual copper beam pipe (94 mm in diameter) with antechambers for wiggler magnets of KEKB. The feed-through was revised to improve reliability, and the length was modified to fit a real magnet. The input power into the electrode was estimated to be approximately 80 W/m. The clear reduction in the electron density was also observed by applying a voltage of +500 V to the electrode. The design of clearing electrodes has now reached a high reliability and it is suitable for accelerator applications.
CLASSE, Ithaca, New York
CERN, Geneva
Carleton University, College of Natural Sciences, Ottawa, Ontario
Purdue University, West Lafayette, Indiana
LBNL, Berkeley, California
Grove City College, Grove City, Pennsylvania
INFN/LNF, Frascati (Roma)
ASCo, Clayton, Victoria
KEK, Ibaraki
Clarkson University, Potsdam, New York
BNL, Upton, Long Island, New York
ANL, Argonne
CalPoly, San Luis Obispo, CA
Cockcroft Institute, Warrington, Cheshire
SLAC, Menlo Park, California
Fermilab, Batavia
Technion, Haifa
Loyola University, Chicago, Illinois
The Cornell Electron Storage Ring (CESR) has been reconfigured as a test accelerator (CesrTA) for a program of electron cloud (EC) research at ultra low emittance. The instrumentation in the ring has been upgraded with local diagnostics for measurement of cloud density and with improved beam diagnostics for the characterization of both the low emittance performance and the beam dynamics of high intensity bunch trains interacting with the cloud. Finally a range of EC mitigation methods have been deployed and tested. Measurements of cloud density and its impact on the beam under a range of conditions will be presented and compared with simulations. The effectiveness of a range of mitigation techniques will also be discussed.
CLASSE, Ithaca, New York
CERN, Geneva
ANL, Argonne
KEK, Ibaraki
SLAC, Menlo Park, California
Over the course of the CesrTA program, the Cornell Electron Storage Ring (CESR) has been instrumented with several retarding field analyzers (RFAs), which measure the local density and energy distribution of the electron cloud. These RFAs have been installed in drifts, dipoles, quadrupoles, and wigglers; and data have been taken in a variety of beam conditions and bunch configurations. This paper will provide an overview of these results, and give a preliminary evaluation of the efficacy of cloud mitigation techniques implemented in the instrumented vacuum chambers.
KEK, Ibaraki
KEKB is an e-/e+ collider for the study of B physics and is also used for machine studies for future machines. The peak luminosity of KEKB, which is the world-highest value, has been still increasing. This report summarizes recent progress at KEKB.
KEK, Ibaraki
OHTSUKA, Tsukuba-shi
The MO (Matsumoto-Ohtsuka) -type flange is suitable for connection flanges of beam pipes for accelerators. The flange uses a metal gasket that exactly fits the aperture of the beam pipe, and has a small beam impedance. The flange can be applied to a complicated aperture. We developed a stainless-steel MO-type flange for a copper beam pipe with antechambers. Several beam pipes were installed in the KEKB B-factory positron ring and were tested using beams. No serious problem was observed up to a beam current of 1600 mA (~10 nC/bunch and ~6 ns bunch spacing). Based on experiences in the stain-less steel case, a possibility of employing copper-alloy and aluminum-alloy MO-type flange has been experimentally studied. They can mitigate the heating problems found in the case of stainless-steel flanges, and simplify the manufacturing procedure of beam pipes made of copper or aluminum alloy. Copper-alloy (CrZrCu) flanges show a comparable vacuum sealing property to the stainless-steel one, and several beam pipes with this flange has been successfully installed in the KEKB. The R&D on aluminum-alloy (A2219 and A2024) flanges has recently started, and a promising result was obtained.
SLAC, Menlo Park, California
LBNL, Berkeley, California
CLASSE, Ithaca, New York
INFN/LNF, Frascati (Roma)
ANL, Argonne
Cockcroft Institute, Warrington, Cheshire
KEK, Ibaraki
CERN, Geneva
As part of the International Linear Collider (ILC) collaboration, we have compared the electron cloud effect for different Damping Ring designs respectively with 6.4 km and 3.2 km circumference and investigated the feasibility of a shorter damping ring with respect to the electron cloud build-up and related beam instability. These studies were carried out with beam parameters of the ILC Low Power option. A reduced damping ring circumference has been proposed for the new ILC baseline design and would allow to considerably reduce the number of components, wiggler magnets and costs. We also briefly discuss the plans for future studies including the luminosity upgrade option with shorter bunch spacing, the evaluation of mitigations and the integration of the CesrTA results into the Damping Ring design.