DESY, Hamburg
JLAB, Newport News, Virginia
The Andrzej Soltan Institute for Nuclear Studies, Centre Swierk, Swierk/Otwock
BNL, Upton, Long Island, New York
In this contribution, we report Quantum Efficiency (QE) test results with a hybrid lead/niobium superconducting RF (SRF) photoinjector at 2K and new Pb arc deposited cathodes at 300K. The ultimate goal of our effort is to build a Nb injector with the superconducting cathode made of lead, which, as reported in the past, demonstrated superior QE compared to other metallic superconducting elements. At first, we present the test results obtained with a 1.6-cell high purity Nb cavity with the emitting lead spot in the center of the back plate. The QE test results at room temperature and the SEM surface analysis of eight Pb cathodes, deposited recently under various conditions, are discussed in the second part of this contribution.
DESY, Hamburg
JLAB, Newport News, Virginia
This paper reports about our efforts to develop a flangeable coaxial coupler for both HOM and fundamental coupling for 9-cell TESLA/ILC-type cavities. The cavities were designed in early 90‘s for pulsed operation with a low duty factor, less than 1 %. The proposed design of the coupler has been done in a way, that the magnetic flux B at the flange connection is minimized and only a field of <5 mT would be present at the accelerating field Eacc of ~ 36 MV/m (B =150 mT in the cavity). Even though we achieved reasonably high Q-values at low field, the cavity/coupler combination was limited in the cw mode to only ~ 7 MV/m, where a thermally initiated degradation occurred. We have improved the cooling conditions by initially drilling radial channels every 30 degrees, then every 15 degrees into the shorting plate. The modified prototype performed well up to 9 MV/m in cw mode. This paper reports about our experiences with the further modified coaxial coupler and about test results in cw and low duty cycle pulsed mode, similar to the TESLA/ILC operation conditions.
DESY, Hamburg
High frequency Higher Order Modes (HOM) propagating in the beam line of a superconducting linac can carry a substantial fraction of the energy deposited in accelerating structures by the beam. In this contribution, we report test results of the beam line absorber (BLA), which was designed and fabricated at DESY, and installed in the FLASH accelerator to absorb the HOM energy generated by high current beams. Two tests were carried out, in September 2008 and September 2009, during so called high current runs. The experiments confirmed the concept of the BLA design and showed remarkable agreement with computer modeling of the HOM energy absorption.
DESY, Hamburg
INFN/LASA, Segrate (MI)
The preparation phase for the European XFEL cavity production includes a number of actions. Material issues: qualification of high purity niobium vendors, verifying of large grain material as a possible option, construction of the scanning device for the niobium sheets. Mechanical fabrication issues: accommodation of the TESLA cavity design to the XFEL demands, device construction for RF measurement of components, integration of the helium tank and it's welding to the cavity into the fabrication sequence, documentation and data transfer, application of a new high resolution camera for inspection of the inside surface. Treatment and RF measurement: establishing the XFEL recipe, in particular the final surface treatment (final 40 μm EP or short 10 μm Flash BCP), and the cavity preparation strategy (vertical acceptance test with or without helium tank welded, with or without assembly of HOM antennas), construction of the cavity tuning machine. About 50 prototype cavities are produced at the industry, treated (partially in industry and partially at DESY) and RF-tested at DESY. The XFEL requirements are fulfilled with a yield of approx. 90%.
DESY, Hamburg
Fermilab, Batavia
Uni HH, Hamburg
Ultra short bunches with high peak current are required for efficient creation of high brilliance coherent light at the free electron laser FLASH. They are obtained by a two stage transverse magnetic chicane bunch compression scheme based on acceleration of the beam off the rf field crest. The deviation of the rf field's sine shape from a straight line leads to long bunch tails and reduces the peak current. This effect will be eliminated by adding the Fermilab-built third harmonic superconducting accelerating module operating at 3.9 GHz to linearize the rf field. The third harmonic module also allows for the creation of uniform intensity bunches of adjustable length that is needed for seeded operation. This paper summarizes the results from the first complete rf system test at the crymodule test bench at DESY and the first experience gained operating the system with beam in FLASH.